scholarly journals A Comparative Study of Turbulence Methods Applied to the Design of a 3D-Printed Scaffold and the Selection of the Appropriate Numerical Scheme to Simulate the Scaffold for Tissue Engineering

2021 ◽  
Vol 12 (1) ◽  
pp. 191
Author(s):  
Miguel Suffo ◽  
Cristobal J. López-Marín
Keyword(s):  
Tissue Engineering ◽  
Comparative Study ◽  
Geometric Model ◽  
Three Dimensional ◽  
Turbulence Models ◽  
Operating Regime ◽  
Elastic Behavior ◽  
Detached Eddy Simulation ◽  
3D Scaffolds ◽  
Fused Deposition

Current commercial software tools implement turbulence models on computational fluid dynamics (CFD) techniques and combine them with fluid-structural interaction (FSI) techniques. There are currently a great variety of turbulence methods that are worth investigating through a comparative study in order to delineate their behavior on scaffolds used in tissue engineering and bone regeneration. Additive manufacturing (AM) offers the opportunity to obtain three-dimensional printed scaffolds (3D scaffolds) that are designed respecting morphologies and that are typically used for the fused deposition model (FDM). These are typically made using biocompatible and biodegradable materials, such as polyetherimide (PEI), ULTEM 1010 biocompatible and polylactic acid (PLA). Starting from our own geometric model, simulations were carried out applying a series of turbulence models which have been proposed due to a variety of properties, such as permeability, speed regime, pressures, depressions and stiffness, that in turn are subject to boundary conditions based on a blood torrent. The obtained results revealed that the detached eddy simulation (DES) model shows better performance for the use of 3D scaffolds in its normal operating regime. Finally, although the results do not present relevant differences between the two materials used in the comparison, the prototypes simulated in PEI ULTEM 1010 do not allow their manufacture in FDM for the required pore size. The printed 3D scaffolds of PLA reveal an elastic behavior and a rigidity that are similar to other prototypes of ceramic composition. Prototypes made of PLA reveal unpredictable variability in pore and layer size which are very similar to cell growth itself and difficult to keep constant.

Development of three-dimensional printing filaments based on poly(lactic acid)/hydroxyapatite composites with potential for tissue engineering

2021 ◽  
pp. 002199832098856
Author(s):  
Marcela Piassi Bernardo ◽  
Bruna Cristina Rodrigues da Silva ◽  
Luiz Henrique Capparelli Mattoso
Keyword(s):  
Tissue Engineering ◽  
Lactic Acid ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Poly Lactic Acid ◽  
Scanning Calorimetry ◽  
Three Dimensional Printing ◽  
Fused Deposition ◽  
Deposition Modeling ◽  
3D Printed

Injured bone tissues can be healed with scaffolds, which could be manufactured using the fused deposition modeling (FDM) strategy. Poly(lactic acid) (PLA) is one of the most biocompatible polymers suitable for FDM, while hydroxyapatite (HA) could improve the bioactivity of scaffold due to its chemical composition. Therefore, the combination of PLA/HA can create composite filaments adequate for FDM and with high osteoconductive and osteointegration potentials. In this work, we proposed a different approache to improve the potential bioactivity of 3D printed scaffolds for bone tissue engineering by increasing the HA loading (20-30%) in the PLA composite filaments. Two routes were investigated regarding the use of solvents in the filament production. To assess the suitability of the FDM-3D printing process, and the influence of the HA content on the polymer matrix, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and scanning electron microscopy (SEM) were performed. The HA phase content of the composite filaments agreed with the initial composite proportions. The wettability of the 3D printed scaffolds was also increased. It was shown a greener route for obtaining composite filaments that generate scaffolds with properties similar to those obtained by the solvent casting, with high HA content and great potential to be used as a bone graft.

Development of Scaffold Building Units and Assembly for Tissue Engineering Using Fused Deposition Modelling

2009 ◽  
Vol 83-86 ◽  
pp. 269-274 ◽  
Author(s):  
Syed H. Masood ◽  
Kadhim Alamara
Keyword(s):  
Tissue Engineering ◽  
Pore Size ◽  
Fused Deposition Modeling ◽  
Porous Scaffold ◽  
Cell Structure ◽  
Three Dimensional ◽  
Three Dimensions ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Unit Cells

In tissue engineering (TE), a porous scaffold structure of biodegradable material is required as a template to guide the proliferation, growth and development of cells appropriately in three dimensions. The scaffold must meet design requirements of appropriate porosity, pore size and interconnected structure to allow cell proliferation and adhesion. This paper presents a methodology for design and manufacture of TE scaffolds with varying porosity by employing open structure building units and Fused Deposition Modeling (FDM) rapid prototyping technique. A computer modeling approach for constructing and assembly of three-dimensional unit cell structure is presented to provide a solution of scaffolds design that can potentially meet the diverse requirements of TE applications. A parametric set of open polyhedral unit cells is used to assist the user in designing the required micro-architecture of the scaffold with required porosity and pore size and then the Boolean operation is used to create the scaffold of a given CAD model from the designed microstructure. The procedure is verified by fabrication of physical scaffolds using the commercial FDM system.

scholarly journals Characterization of Three-Dimensional Printed Composite Scaffolds Prepared with Different Fabrication Methods

2016 ◽  
Vol 61 (2) ◽  
pp. 645-650 ◽  
Author(s):  
K. Szlązak ◽  
J. Jaroszewicz ◽  
B. Ostrowska ◽  
T. Jaroszewicz ◽  
M. Nabiałek ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
Fused Deposition Modeling ◽  
Testing Machine ◽  
Three Dimensional ◽  
Gravimetric Analysis ◽  
Solution Casting ◽  
Micro Computed Tomography ◽  
Optimal Method ◽  
Fused Deposition ◽  
Material Testing Machine

Abstract An optimal method for composites preparation as an input to rapid prototyping fabrication of scaffolds with potential application in osteochondral tissue engineering is still needed. Scaffolds in tissue engineering applications play a role of constructs providing appropriate mechanical support with defined porosity to assist regeneration of tissue. The aim of the presented study was to analyze the influence of composite fabrication methods on scaffolds mechanical properties. The evaluation was performed on polycaprolactone (PCL) with 5 wt% beta-tricalcium phosphate (TCP) scaffolds fabricated using fused deposition modeling (FDM). Three different methods of PCL-TCP composite preparation: solution casting, particles milling, extrusion and injection were used to provide material for scaffold fabrication. The obtained scaffolds were investigated by means of scanning electron microscope, x-ray micro computed tomography, thermal gravimetric analysis and static material testing machine. All of the scaffolds had the same geometry (cylinder, 4×6 mm) and fiber orientation (0/60/120°). There were some differences in the TCP distribution and formation of the ceramic agglomerates in the scaffolds. They depended on fabrication method. The use of composites prepared by solution casting method resulted in scaffolds with the best combination of compressive strength (5.7±0.2 MPa) and porosity (48.5±2.7 %), both within the range of trabecular bone.

scholarly journals Naturally Prefabricated Marine Biomaterials: Isolation and Applications of Flat Chitinous 3D Scaffolds from Ianthella labyrinthus (Demospongiae: Verongiida)

2019 ◽  
Vol 20 (20) ◽  
pp. 5105 ◽  
Author(s):  
Mario Schubert ◽  
Björn Binnewerg ◽  
Alona Voronkina ◽  
Lyubov Muzychka ◽  
Marcin Wysokowski ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
Three Dimensional ◽  
Marine Sponges ◽  
Biologically Active ◽  
3D Scaffolds ◽  
Chemical Treatments ◽  
The Family ◽  
Unique Source ◽  
Induced Pluripotent ◽  
First Time

Marine sponges remain representative of a unique source of renewable biological materials. The demosponges of the family Ianthellidae possess chitin-based skeletons with high biomimetic potential. These three-dimensional (3D) constructs can potentially be used in tissue engineering and regenerative medicine. In this study, we focus our attention, for the first time, on the marine sponge Ianthella labyrinthus Bergquist & Kelly-Borges, 1995 (Demospongiae: Verongida: Ianthellidae) as a novel potential source of naturally prestructured bandage-like 3D scaffolds which can be isolated simultaneously with biologically active bromotyrosines. Specifically, translucent and elastic flat chitinous scaffolds have been obtained after bromotyrosine extraction and chemical treatments of the sponge skeleton with alternate alkaline and acidic solutions. For the first time, cardiomyocytes differentiated from human induced pluripotent stem cells (iPSC-CMs) have been used to test the suitability of I. labyrinthus chitinous skeleton as ready-to-use scaffold for their cell culture. Results reveal a comparable attachment and growth on isolated chitin-skeleton, compared to scaffolds coated with extracellular matrix mimetic Geltrex®. Thus, the natural, unmodified I. labyrinthus cleaned sponge skeleton can be used to culture iPSC-CMs and 3D tissue engineering. In addition, I. labyrinthus chitin-based scaffolds demonstrate strong and efficient capability to absorb blood deep into the microtubes due to their excellent capillary effect. These findings are suggestive of the future development of new sponge chitin-based absorbable hemostats as alternatives to already well recognized cellulose-based fabrics.

scholarly journals Comparative Study on CFD Turbulence Models for the Flow Field in Air Cooled Radiator

Processes ◽  
2020 ◽  
Vol 8 (12) ◽  
pp. 1687
Author(s):  
Chao Yu ◽  
Xiangyao Xue ◽  
Kui Shi ◽  
Mingzhen Shao ◽  
Yang Liu
Keyword(s):  
Flow Field ◽  
Transient Flow ◽  
Three Dimensional ◽  
Turbulence Models ◽  
Compartment Model ◽  
Navier Stokes ◽  
Engine Compartment ◽  
Detached Eddy Simulation ◽  
Eddy Simulation ◽  
Relevant Calculation

This paper compares the performances of three Computational Fluid Dynamics (CFD) turbulence models, Reynolds Average Navier-Stokes (RANS), Detached Eddy Simulation (DES), and Large Eddy Simulation (LES), for simulating the flow field of a wheel loader engine compartment. The distributions of pressure fields, velocity fields, and vortex structures in a hybrid-grided engine compartment model are analyzed. The result reveals that the LES and DES can capture the detachment and breakage of the trailing edge more abundantly and meticulously than RANS. Additionally, by comparing the relevant calculation time, the feasibility of the DES model is proved to simulate the three-dimensional unsteady flow of engine compartment efficiently and accurately. This paper aims to provide a guiding idea for simulating the transient flow field in the engine compartment, which could serve as a theoretical basis for optimizing and improving the layout of the components of the engine compartment.

scholarly journals Hybrid Tissue Engineering Scaffolds by Combination of Three-Dimensional Printing and Cell Photoencapsulation

2015 ◽  
Vol 6 (2) ◽  
Author(s):  
Marica Markovic ◽  
Jasper Van Hoorick ◽  
Katja Hölzl ◽  
Maximilian Tromayer ◽  
Peter Gruber ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
Fused Deposition Modeling ◽  
Structural Parameters ◽  
Three Dimensional ◽  
Poly Lactic Acid ◽  
Tissue Engineering Scaffolds ◽  
Ecm Remodeling ◽  
Initial Cell ◽  
Fused Deposition ◽  
Hydrogel Matrix

Three-dimensional (3D) printing offers versatile possibilities for adapting the structural parameters of tissue engineering scaffolds. However, it is also essential to develop procedures allowing efficient cell seeding independent of scaffold geometry and pore size. The aim of this study was to establish a method for seeding the scaffolds using photopolymerizable cell-laden hydrogels. The latter facilitates convenient preparation, and handling of cell suspension, while distributing the hydrogel precursor throughout the pores, before it is cross-linked with light. In addition, encapsulation of living cells within hydrogels can produce constructs with high initial cell loading and intimate cell-matrix contact, similar to that of the natural extra-cellular matrix (ECM). Three dimensional scaffolds were produced from poly(lactic) acid (PLA) by means of fused deposition modeling. A solution of methacrylamide-modified gelatin (Gel-MOD) in cell culture medium containing photoinitiator Li-TPO-L was used as a hydrogel precursor. Being an enzymatically degradable derivative of natural collagen, gelatin-based matrices are biomimetic and potentially support the process of cell-induced remodeling. Preosteoblast cells MC3T3-E1 at a density of 10 × 106 cells per 1 mL were used for testing the seeding procedure and cell proliferation studies. Obtained results indicate that produced constructs support cell survival and proliferation over extended duration of our experiment. The established two-step approach for scaffold seeding with the cells is simple, rapid, and is shown to be highly reproducible. Furthermore, it enables precise control of the initial cell density, while yielding their uniform distribution throughout the scaffold. Such hybrid tissue engineering constructs merge the advantages of rigid 3D printed constructs with the soft hydrogel matrix, potentially mimicking the process of ECM remodeling.

New Insight Into the Flow Around a Wind Turbine Airfoil Section1

2005 ◽  
Vol 127 (2) ◽  
pp. 214-222 ◽  
Author(s):  
F. Bertagnolio ◽  
N. N. Sørensen ◽  
F. Rasmussen
Keyword(s):  
Wind Turbine ◽  
Numerical Models ◽  
Turbine Blades ◽  
Three Dimensional ◽  
Unsteady Aerodynamics ◽  
Turbulence Models ◽  
Navier Stokes ◽  
Detached Eddy Simulation ◽  
Pitching Airfoil ◽  
Wind Turbine Airfoil

The objective of this paper is an improved understanding of the physics of the aeroelastic motion of wind turbine blades in order to improve the numerical models used for their design. Two- and three-dimensional Navier–Stokes calculations of the flow around a wind turbine airfoil using the k−ω SST and Detached Eddy Simulation (DES) turbulence models, as well as an engineering semiempirical dynamic stall model, are conducted. The computational results are compared to the experimental results that are available for both the static airfoil and the pitching airfoil. It is shown that the Navier–Stokes simulations can reproduce the main characteristic features of the flow. The DES model seems to be able to reproduce most of the details of the unsteady aerodynamics. Aerodynamic work computations indicate that a plunging motion of the airfoil can become unstable.

scholarly journals Freeze-dried multiscale porous nanofibrous three dimensional scaffolds for bone regenerations

Bioimpacts ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 73-85 ◽  
Author(s):  
Maryam Sadat Khoramgah ◽  
Javad Ranjbari ◽  
Hojjat-Allah Abbaszadeh ◽  
Fatemeh Sadat Tabatabaei Mirakabad ◽  
Shadie Hatami ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
Bone Tissue Engineering ◽  
Bone Tissue ◽  
Freeze Drying ◽  
Three Dimensional ◽  
Cross Linking ◽  
Drying Methods ◽  
3D Scaffolds ◽  
Hierarchical Porous ◽  
Physicochemical Features

Introduction: Simulating hydrophobic-hydrophilic composite face with hierarchical porous and fibrous architectures of bone extracellular matrix (ECM) is a key aspect in bone tissue engineering. This study focused on the fabrication of new three-dimensional (3D) scaffolds containing polytetrafluoroethylene (PTFE), and polyvinyl alcohol (PVA), with and without graphene oxide (GO) nanoparticles using the chemical cross-linking and freeze-drying methods for bone tissue application. The effects of GO on physicochemical features and osteoinduction properties of the scaffolds were evaluated through an in vitro study. Methods: After synthesizing the GO nanoparticles, two types of 3D scaffolds, PTFE/PVA (PP) and PTFE/PVA/GO (PPG), were developed by cross-linking and freeze-drying methods. The physicochemical features of scaffolds were assessed and the interaction of the 3D scaffold types with human adipose mesenchymal stem cells (hADSCs) including attachment, proliferation, and differentiation to osteogenic like cells were investigated. Results: GO nanoparticles were successfully synthesized with no agglomeration. The blending of PTFE as a hydrophobic polymer with PVA polymer and GO nanoparticles (hydrophilic compartments) were successful. Two types of 3D scaffolds had nano topographical structures, good porosities, hydrophilic surfaces, thermal stabilities, good stiffness, as well as supporting the cell attachments, proliferation, and osteogenic differentiation. Notably, GO incorporating scaffolds provided a better milieu for cell behaviors. Conclusion: Novel multiscale porous nanofibrous 3D scaffolds made from PTFE/ PVA polymers with and without GO nanoparticles could be an ideal candidate for bone tissue engineering as a 3D template.

A Robust True Direct-Print Technology for Tissue Engineering

2007 ◽  
Author(s):  
B. Li ◽  
T. Dutta Roy ◽  
C. M. Smith ◽  
P. A. Clark ◽  
K. H. Church
Keyword(s):  
Tissue Engineering ◽  
Computer Aided Design ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Layer By Layer ◽  
Fused Deposition ◽  
Wide Range ◽  
Computer Aided ◽  
Liquid Material ◽  
Print Process

Numerous solid freeform fabrication (SFF) or rapid prototyping (RP) techniques have been employed in the field of tissue engineering to fabricate specially organized three-dimensional (3-D) structures such as scaffolds. Some such technologies include, but are not limited to, laminated object manufacturing (LOM), three-dimensional printing (3-DP) or ink-jet printing, selective laser sintering (SLS), and fused deposition modeling (FDM). These techniques are capable of rapidly producing highly complex 3-D scaffolds or other biomedical structures with the aid of a computer-aided design (CAD) system. However, they suffer from lack of consistency and repeatability, since most of these processes are not fully controlled and cannot reproduce the previous work with accuracy. Also, these techniques (excluding FDM) are not truly direct-print processes. Certain material removing steps are involved, which in turn increases the complexity and the cost of fabrication. The FDM process has good repeatability; however, the materials that can be used are limited due to the high temperature needed to melt the feedstock. Some researchers also reported that the scaffolds fabricated by FDM lack consistency in the z-direction. In this paper, we will present a true direct-print technology for repeatedly producing scaffolds and other biomedical structures for tissue engineering with the aid of our Computer Aided Biological (CAB) tool. Unlike other SFF techniques mentioned above, our direct-print process fabricates scaffolds or other complex 3-D structures by extruding (dispensing) a liquid material onto the substrate with a prescribed pattern generated by a CAD program. This can be a layer-by-layer 2.5 dimension build or a true 3-D build. The dispensed liquid material then polymerizes or solidifies, to form a solid structure. The flexibility in the types of materials that can be extruded ranges from polymers to living cells, encapsulated in the proper material. True 3-D structures are now possible on a wide range of substrates, including even in vivo. Some of the advantages of the process are a) researchers have full control over the patterns to be created; b) it is a true direct-print process with no material removing steps involved; c) it is highly consistent and repeatable; and d) it is highly efficient and cost-effective. This paper will first give a detailed description of the CAB tool. Then, it will present a detailed process for printing polycaprolactone (PCL) into a defined 3-D architecture, where the primary focus for these constructs is for use in tissue engineering applications. Finally, mechanical characterization results of the printed scaffolds will be included in the paper.

Adaptive Detached-Eddy Simulation of Three-Dimensional Diffusers

2016 ◽  
Vol 138 (10) ◽  
Author(s):  
Paul Durbin ◽  
Zifei Yin ◽  
Elbert Jeyapaul
Keyword(s):  
Pressure Coefficient ◽  
Three Dimensional ◽  
Side Wall ◽  
Turbulence Models ◽  
Adaptive Method ◽  
Detached Eddy Simulation ◽  
Mean Velocity ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Default Data

An adaptive method for detached-eddy simulation (DES) is tested by simulations of flow in a family of three-dimensional (3D) diffusers. The adaptive method either adjusts the model constant or defaults to a bound if the grid is too coarse. On the present grids, the adaptive method adjusts the model constant over most of the flow, without resorting to the default. Data for the diffuser family were created by wall-resolved, large-eddy simulation (LES), using the dynamic Smagorinsky model, for the purpose of testing turbulence models. The family is a parameterized set of geometries that allows one to test whether the pattern of separation is moving correctly from the top to the side wall as the parameter increases. The adaptive DES model is quite accurate in this regard. It is found to predict the mean velocity accurately, but the pressure coefficient is underpredicted. The latter is due to the onset of separation being slightly earlier in the DES than in the LES.

Sign in / Sign up

Export Citation Format

Share Document