scholarly journals Biomimicry in Bio-Manufacturing: Developments in Melt Electrospinning Writing Technology Towards Hybrid Biomanufacturing

2019 ◽  
Vol 9 (17) ◽  
pp. 3540 ◽  
Author(s):  
Ferdows Afghah ◽  
Caner Dikyol ◽  
Mine Altunbek ◽  
Bahattin Koc
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Cell Attachment ◽  
Three Dimensional ◽  
Future Perspective ◽  
Melt Electrospinning ◽  
Wide Range ◽  
Challenges And Opportunities ◽  
Potential Applications ◽  
Homogeneous Cell

Melt electrospinning writing has been emerged as a promising technique in the field of tissue engineering, with the capability of fabricating controllable and highly ordered complex three-dimensional geometries from a wide range of polymers. This three-dimensional (3D) printing method can be used to fabricate scaffolds biomimicking extracellular matrix of replaced tissue with the required mechanical properties. However, controlled and homogeneous cell attachment on melt electrospun fibers is a challenge. The combination of melt electrospinning writing with other tissue engineering approaches, called hybrid biomanufacturing, has introduced new perspectives and increased its potential applications in tissue engineering. In this review, principles and key parameters, challenges, and opportunities of melt electrospinning writing, and particularly, recent approaches and materials in this field are introduced. Subsequently, hybrid biomanufacturing strategies are presented for improved biological and mechanical properties of the manufactured porous structures. An overview of the possible hybrid setups and applications, future perspective of hybrid processes, guidelines, and opportunities in different areas of tissue/organ engineering are also highlighted.

scholarly journals Additive Manufacturing of Biopolymers for Tissue Engineering and Regenerative Medicine: An Overview, Potential Applications, Advancements, and Trends

2021 ◽  
Vol 2021 ◽  
pp. 1-20 ◽  
Author(s):  
Dhinakaran Veeman ◽  
M. Swapna Sai ◽  
P. Sureshkumar ◽  
T. Jagadeesha ◽  
L. Natrayan ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
Additive Manufacturing ◽  
3D Printing ◽  
Regenerative Medicine ◽  
Tissue Regeneration ◽  
Three Dimensional ◽  
Porous Scaffolds ◽  
Wide Range ◽  
Potential Applications ◽  
Pharmaceutical Industries

As a technique of producing fabric engineering scaffolds, three-dimensional (3D) printing has tremendous possibilities. 3D printing applications are restricted to a wide range of biomaterials in the field of regenerative medicine and tissue engineering. Due to their biocompatibility, bioactiveness, and biodegradability, biopolymers such as collagen, alginate, silk fibroin, chitosan, alginate, cellulose, and starch are used in a variety of fields, including the food, biomedical, regeneration, agriculture, packaging, and pharmaceutical industries. The benefits of producing 3D-printed scaffolds are many, including the capacity to produce complicated geometries, porosity, and multicell coculture and to take growth factors into account. In particular, the additional production of biopolymers offers new options to produce 3D structures and materials with specialised patterns and properties. In the realm of tissue engineering and regenerative medicine (TERM), important progress has been accomplished; now, several state-of-the-art techniques are used to produce porous scaffolds for organ or tissue regeneration to be suited for tissue technology. Natural biopolymeric materials are often better suited for designing and manufacturing healing equipment than temporary implants and tissue regeneration materials owing to its appropriate properties and biocompatibility. The review focuses on the additive manufacturing of biopolymers with significant changes, advancements, trends, and developments in regenerative medicine and tissue engineering with potential applications.

3D printing in tissue engineering: a state of the art review of technologies and biomaterials

2020 ◽  
Vol 26 (7) ◽  
pp. 1313-1334 ◽  
Author(s):  
Nataraj Poomathi ◽  
Sunpreet Singh ◽  
Chander Prakash ◽  
Arjun Subramanian ◽  
Rahul Sahay ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
3D Printing ◽  
Regenerative Medicine ◽  
State Of The Art ◽  
Three Dimensional ◽  
Cost Effective ◽  
Cochrane Library ◽  
Content Type ◽  
Wide Range ◽  
Potential Applications

Purpose In the past decade, three-dimensional (3D) printing has gained attention in areas such as medicine, engineering, manufacturing art and most recently in education. In biomedical, the development of a wide range of biomaterials has catalysed the considerable role of 3D printing (3DP), where it functions as synthetic frameworks in the form of scaffolds, constructs or matrices. The purpose of this paper is to present the state-of-the-art literature coverage of 3DP applications in tissue engineering (such as customized scaffoldings and organs, and regenerative medicine). Design/methodology/approach This review focusses on various 3DP techniques and biomaterials for tissue engineering (TE) applications. The literature reviewed in the manuscript has been collected from various journal search engines including Google Scholar, Research Gate, Academia, PubMed, Scopus, EMBASE, Cochrane Library and Web of Science. The keywords that have been selected for the searches were 3 D printing, tissue engineering, scaffoldings, organs, regenerative medicine, biomaterials, standards, applications and future directions. Further, the sub-classifications of the keyword, wherever possible, have been used as sectioned/sub-sectioned in the manuscript. Findings 3DP techniques have many applications in biomedical and TE (B-TE), as covered in the literature. Customized structures for B-TE applications are easy and cost-effective to manufacture through 3DP, whereas on many occasions, conventional technologies generally become incompatible. For this, this new class of manufacturing must be explored to further capabilities for many potential applications. Originality/value This review paper presents a comprehensive study of the various types of 3DP technologies in the light of their possible B-TE application as well as provides a future roadmap.

Piezoelectric Poly(3-hydroxybutyrate)-Poly(lactic acid) Three Dimensional Scaffolds for Bone Tissue Engineering

2007 ◽  
Vol 1025 ◽  
Author(s):  
Juana Mendenhall ◽  
Dapeng Li ◽  
Margaret Frey ◽  
Juan Hinestroza ◽  
Omotunde Babalola ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Lactic Acid ◽  
Surface Topography ◽  
Cell Attachment ◽  
Three Dimensional ◽  
Poly Lactic Acid ◽  
Coverage Area ◽  
Surface Initiated Polymerization ◽  
Natural Tissue

AbstractThree dimensional scaffolds (3D) are promising for future nanoscale materials and tissue engineering applications being that they have architecture and mechanical properties similar to natural tissue. In this work, poly(lactic acid) fibers were prepared via electrospinnig with average diameters of 2580 nm. Using Enzymatic Surface-Initiated polymerization (ESIP), poly(3-hydroxybutyrate) were coated on poly(lactic acid) fibers. This provides an alternative method to enzymatic surface modification of fibers. ESIP of PHB produces a granular film providing surface topography and increases mechanical properties of PLA fibers alone. When using covalent approaches, PHB granules provide surface topography of 200-500 nm with a polydisperse coverage area. Compressive modulus measurements of PLA and PHB/PLA scaffolds were 25 kPa and 73 kPa, respectively. The percent crystallinity of PLA and PHB/PLA scaffolds was 17% and 30%, respectively. This rough topography, in addition to the crystallinity of the scaffold, facilitates Soas-2 osteoblast cell attachment. We have observed attachment of the osteoblast cells along the length of the oriented PLA and PHB/PLA composite scaffolds with different morphologies, rounded and stretched, throughout a depth of 90 µm.

scholarly journals Is Dialdehyde Chitosan a Good Substance to Modify Physicochemical Properties of Biopolymeric Materials?

2021 ◽  
Vol 22 (7) ◽  
pp. 3391
Author(s):  
Sylwia Grabska-Zielińska ◽  
Alina Sionkowska ◽  
Ewa Olewnik-Kruszkowska ◽  
Katarzyna Reczyńska ◽  
Elżbieta Pamuła
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Physicochemical Properties ◽  
Silk Fibroin ◽  
Three Dimensional ◽  
Microscopy Imaging ◽  
Maximum Deformation ◽  
One Step ◽  
Chitosan Blends ◽  
Fourier Transfer Infrared Spectroscopy

The aim of this work was to compare physicochemical properties of three dimensional scaffolds based on silk fibroin, collagen and chitosan blends, cross-linked with dialdehyde starch (DAS) and dialdehyde chitosan (DAC). DAS was commercially available, while DAC was obtained by one-step synthesis. Structure and physicochemical properties of the materials were characterized using Fourier transfer infrared spectroscopy with attenuated total reflectance device (FTIR-ATR), swelling behavior and water content measurements, porosity and density observations, scanning electron microscopy imaging (SEM), mechanical properties evaluation and thermogravimetric analysis. Metabolic activity with AlamarBlue assay and live/dead fluorescence staining were performed to evaluate the cytocompatibility of the obtained materials with MG-63 osteoblast-like cells. The results showed that the properties of the scaffolds based on silk fibroin, collagen and chitosan can be modified by chemical cross-linking with DAS and DAC. It was found that DAS and DAC have different influence on the properties of biopolymeric scaffolds. Materials cross-linked with DAS were characterized by higher swelling ability (~4000% for DAS cross-linked materials; ~2500% for DAC cross-linked materials), they had lower density (Coll/CTS/30SF scaffold cross-linked with DAS: 21.8 ± 2.4 g/cm3; cross-linked with DAC: 14.6 ± 0.7 g/cm3) and lower mechanical properties (maximum deformation for DAC cross-linked scaffolds was about 69%; for DAS cross-linked scaffolds it was in the range of 12.67 ± 1.51% and 19.83 ± 1.30%) in comparison to materials cross-linked with DAC. Additionally, scaffolds cross-linked with DAS exhibited higher biocompatibility than those cross-linked with DAC. However, the obtained results showed that both types of scaffolds can provide the support required in regenerative medicine and tissue engineering. The scaffolds presented in the present work can be potentially used in bone tissue engineering to facilitate healing of small bone defects.

scholarly journals A Slot-Die Technique for the Preparation of Continuous, High-Area, Chitosan-Based Thin Films

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1566
Author(s):  
Oliver J. Pemble ◽  
Maria Bardosova ◽  
Ian M. Povey ◽  
Martyn E. Pemble
Keyword(s):  
Thin Films ◽  
Mechanical Properties ◽  
High Volume ◽  
Mechanical Anisotropy ◽  
Diverse Range ◽  
Direction Parallel ◽  
High Area ◽  
Wide Range ◽  
Slot Die ◽  
Potential Applications

Chitosan-based films have a diverse range of potential applications but are currently limited in terms of commercial use due to a lack of methods specifically designed to produce thin films in high volumes. To address this limitation directly, hydrogels prepared from chitosan, chitosan-tetraethoxy silane, also known as tetraethyl orthosilicate (TEOS) and chitosan-glutaraldehyde have been used to prepare continuous thin films using a slot-die technique which is described in detail. By way of preliminary analysis of the resulting films for comparison purposes with films made by other methods, the mechanical strength of the films produced was assessed. It was found that as expected, the hybrid films made with TEOS and glutaraldehyde both show a higher yield strength than the films made with chitosan alone. In all cases, the mechanical properties of the films were found to compare very favorably with similar measurements reported in the literature. In order to assess the possible influence of the direction in which the hydrogel passes through the slot-die on the mechanical properties of the films, testing was performed on plain chitosan samples cut in a direction parallel to the direction of travel and perpendicular to this direction. It was found that there was no evidence of any mechanical anisotropy induced by the slot die process. The examples presented here serve to illustrate how the slot-die approach may be used to create high-volume, high-area chitosan-based films cheaply and rapidly. It is suggested that an approach of the type described here may facilitate the use of chitosan-based films for a wide range of important applications.

scholarly journals An Overview on the Rheology, Mechanical Properties, Durability, 3D Printing, and Microstructural Performance of Nanomaterials in Cementitious Composites

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2950
Author(s):  
Hongwei Song ◽  
Xinle Li
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Three Dimensional ◽  
Cementitious Materials ◽  
Research Area ◽  
Cementitious Composites ◽  
Split Tensile Strength ◽  
Contour Crafting ◽  
Wide Range ◽  
Active Research

The most active research area is nanotechnology in cementitious composites, which has a wide range of applications and has achieved popularity over the last three decades. Nanoparticles (NPs) have emerged as possible materials to be used in the field of civil engineering. Previous research has concentrated on evaluating the effect of different NPs in cementitious materials to alter material characteristics. In order to provide a broad understanding of how nanomaterials (NMs) can be used, this paper critically evaluates previous research on the influence of rheology, mechanical properties, durability, 3D printing, and microstructural performance on cementitious materials. The flow properties of fresh cementitious composites can be measured using rheology and slump. Mechanical properties such as compressive, flexural, and split tensile strength reveal hardened properties. The necessary tests for determining a NM’s durability in concrete are shrinkage, pore structure and porosity, and permeability. The advent of modern 3D printing technologies is suitable for structural printing, such as contour crafting and binder jetting. Three-dimensional (3D) printing has opened up new avenues for the building and construction industry to become more digital. Regardless of the material science, a range of problems must be tackled, including developing smart cementitious composites suitable for 3D structural printing. According to the scanning electron microscopy results, the addition of NMs to cementitious materials results in a denser and improved microstructure with more hydration products. This paper provides valuable information and details about the rheology, mechanical properties, durability, 3D printing, and microstructural performance of cementitious materials with NMs and encourages further research.

scholarly journals Improved Bioactivity of 3D Printed Porous Titanium Alloy Scaffold with Chitosan/Magnesium-Calcium Silicate Composite for Orthopaedic Applications

Materials ◽  
2019 ◽  
Vol 12 (2) ◽  
pp. 203 ◽  
Author(s):  
Chun-Hao Tsai ◽  
Chih-Hung Hung ◽  
Che-Nan Kuo ◽  
Cheng-Yu Chen ◽  
Yu-Ning Peng ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Calcium Silicate ◽  
Cell Attachment ◽  
Three Dimensional ◽  
Bone Defects ◽  
Metal Alloys ◽  
Potential Candidate ◽  
Natural Bone

Recently, cases of bone defects have been increasing incrementally. Thus, repair or replacement of bone defects is gradually becoming a huge problem for orthopaedic surgeons. Three-dimensional (3D) scaffolds have since emerged as a potential candidate for bone replacement, of which titanium (Ti) alloys are one of the most promising candidates among the metal alloys due to their low cytotoxicity and mechanical properties. However, bioactivity remains a problem for metal alloys, which can be enhanced using simple immersion techniques to coat bioactive compounds onto the surface of Ti–6Al–4V scaffolds. In our study, we fabricated magnesium-calcium silicate (Mg–CS) and chitosan (CH) compounds onto Ti–6Al–4V scaffolds. Characterization of these surface-modified scaffolds involved an assessment of physicochemical properties as well as mechanical testing. Adhesion, proliferation, and growth of human Wharton’s Jelly mesenchymal stem cells (WJMSCs) were assessed in vitro. In addition, the cell attachment morphology was examined using scanning electron microscopy to assess adhesion qualities. Osteogenic and mineralization assays were conducted to assess osteogenic expression. In conclusion, the Mg–CS/CH coated Ti–6Al–4V scaffolds were able to exhibit and retain pore sizes and their original morphologies and architectures, which significantly affected subsequent hard tissue regeneration. In addition, the surface was shown to be hydrophilic after modification and showed mechanical strength comparable to natural bone. Not only were our modified scaffolds able to match the mechanical properties of natural bone, it was also found that such modifications enhanced cellular behavior such as adhesion, proliferation, and differentiation, which led to enhanced osteogenesis and mineralization downstream. In vivo results indicated that Mg–CS/CH coated Ti–6Al–4V enhances the bone regeneration and ingrowth at the critical size bone defects of rabbits. These results indicated that the proposed Mg–CS/CH coated Ti–6Al–4V scaffolds exhibited a favorable, inducive micro-environment that could serve as a promising modification for future bone tissue engineering scaffolds.

Application of Microbial Polyesters-Polyhydroxyalkanoates as Tissue Engineering Materials

2005 ◽  
Vol 288-289 ◽  
pp. 437-440 ◽  
Author(s):  
Guo Qiang Chen ◽  
Qiong Wu ◽  
Ya Wu Wang ◽  
Zhong Zheng
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Surface Treatment ◽  
Surface Properties ◽  
Three Dimensional ◽  
Material Surface ◽  
New Class ◽  
Molecular Studies ◽  
Cartilage Cells ◽  
Engineering Materials

Poly(hydroxybutyrate-co-hydroxyhexanoate) (PHBHHx) has improved mechanical properties over the existing PHA and our results have shown that PHBHHx has better biocompatibility over polyhydroxybutyrate (PHB) and polylactic acid (PLA). Surface treatment with lipases dramatically changed the material surface properties and increased the biocompatibility of the PHBHHx. PHBHHx and its PHB blends had been used to make three dimensional structures and it has been found that cartilage, osteoblast, and fibroblasts all showed strong growth on the PHBHHx scaffolds. The growth was much better compared with PLA. The molecular studies also showed that mRNA encoding cartilages were strongly expressed when cartilage cells were grown on the PHBHHx. As PHBHHx has strong mechanical properties, easily processible and biodegradable, this material can be used to develop a new class of tissue engineering materials.

Combined Effects of Scaffold Material and Mechanical Stimulation on the Formation of Tissue Engineered Constructs Using Tendon and Ligament Progenitor Cells

2013 ◽  
Author(s):  
Andrew P. Breidenbach ◽  
Nathaniel A. Dyment ◽  
Yinhui Lu ◽  
Jason T. Shearn ◽  
David W. Rowe ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tissue Engineering ◽  
Progenitor Cells ◽  
Three Dimensional ◽  
Musculoskeletal Injuries ◽  
Combined Effects ◽  
Joint Movement ◽  
Scaffold Material ◽  
Ligament Injuries ◽  
Promising Alternative

Tendon and ligament injuries account for one-third of all musculoskeletal injuries [1]. Collagen fibrils in these mechanosensitive tissues transmit forces to mobilize and stabilize joint movement. Donor tissues used to repair these tissues often lack the mechanical properties of the tissue they are replacing. One promising alternative using tissue engineering combines stem/progenitor cells in three-dimensional tissue engineered constructs (TECs).

Sign in / Sign up

Export Citation Format

Share Document