scholarly journals Threading Performance of Different Coatings for High Speed Steel Tapping

Coatings ◽  
2020 ◽  
Vol 10 (5) ◽  
pp. 464
Author(s):  
Alain Gil Del Val ◽  
Fernando Veiga ◽  
Octavio Pereira ◽  
Luis Norberto Lopez De Lacalle
Keyword(s):  
Tool Life ◽  
Vapor Deposition ◽  
Physical Vapor Deposition ◽  
High Speed ◽  
Cutting Speed ◽  
High Speed Steel ◽  
Tialn Coating ◽  
Tool Performance ◽  
Thread Profile ◽  
Increase Tool Life

Threading holes using tapping tools is a widely used machining operation in the industry. This manufacturing process involves a great tool immersion in the part, which involves both friction and cutting. This makes the use of coatings critical to improving tool life. Four coatings are used based on Physical vapor deposition (PVD) technology—TiN, TiCN, TiAlN and TiAlN+WC/C are compared to uncoated tool performance. The effect of various coatings on the life of M12 × 1.5 tapping tools during threading of through holes 20 mm deep, in GG25 casting plates, dry and applying cutting speed of 50 m/min. The end-of-life criterion has been established based on a cutting torque of 16 N-m. Taking the uncoated tap as a basis for comparison, it is observed that coatings based on PVD technologies increase tool life doubling in the most advantageous case with the TiAlN coating. PVD type coatings provide better protection to wear at cylindrical area of the tool, where the thread profile is finished, than uncoated taps. The teeth located in the cone-cylinder transition zone of the taps suffer the most wear regardless of the coating. However, taps coated with TiAlN+WC/C wear level values is lowest of all the coatings tested, which indicates a strong reinforcement in these teeth.

Evaluation of Tool Performance of Recycle-Type Fe3Al Based Alloy for Pure Cu

2014 ◽  
Vol 783-786 ◽  
pp. 1142-1146
Author(s):  
Takaomi Itoi ◽  
Tomoaki Sudo ◽  
Kyosuke Yoshimi
Keyword(s):  
Tool Life ◽  
High Speed ◽  
Cutting Speed ◽  
High Speed Steel ◽  
Induction Melting ◽  
Iron Aluminum ◽  
Tool Performance ◽  
Pure Cu ◽  
The Relationship

Recycle-type Fe3Al (hereinafter designated as Re-Fe3Al) based alloys reinforced by the carbides of TiC or ZrC were processed by the high frequency induction melting method using a high-carbon Cr steel sludge, Al can scraps and the transition metals of Ti or Zr. The carbides were synthesized by in-situ reaction between the transition metal and carbon in the molten iron aluminum alloy. Vickers hardness values are 309HV0.5 for Re-Fe3Al/TiC alloy, and 473HV0.5 for Re-Fe3Al/ZrC alloy, which are higher than that of P-Fe3Al (preprared from pure-Fe and-Al). The cutting performance of the Re-Fe3Al baed alloys was compared with a High-Speed-Steel (HSS) by cutting tests for pure-Cu extruded bar (C1020) using a lathe under a dry condition. Tool life limit was estimated from frank wear length after the cutting tests of C1020 by finish-machining. Tool life limit of Re-Fe3Al/TiC alloy is more than16 min; P-Fe3Al was 12 min; HSS was 8 min, Re-Fe3Al/ZrC alloy was 7 min at the cutting speed of 100m/min. Also, tool life limit of the Re-Fe3Al/TiC alloy was more than twice times as long as that of the HSS at the cutting speed of 300/min. The relationship between cutting speed and tool life limit clearly indicated that the Re-Fe3Al/TiC alloy was better than the HSS at a higher cutting speed. Therefore, it was concluded that Re-Fe3Al/TiC alloy has excellent cutting tool performance.

scholarly journals Investigation on the corrosion behavior of physical vapor deposition coated high speed steel

2015 ◽  
Vol 7 (8) ◽  
pp. 168781401559952 ◽  
Author(s):  
R Ravi Raja Malarvannan ◽  
TV Moorthy ◽  
S Sathish ◽  
P Hariharan
Keyword(s):  
Corrosion Behavior ◽  
Vapor Deposition ◽  
Physical Vapor Deposition ◽  
High Speed ◽  
High Speed Steel

Evolution of TiN Coating Surface Roughness during Physical Vapor Deposition on High Speed Steel Substrate

2014 ◽  
Vol 604 ◽  
pp. 67-70
Author(s):  
Leonid Kupchenko ◽  
Rauno Tali ◽  
Eron Adoberg ◽  
Valdek Mikli ◽  
Vitali Podgursky
Keyword(s):  
Surface Roughness ◽  
Vapor Deposition ◽  
Physical Vapor Deposition ◽  
High Speed ◽  
Steel Substrate ◽  
High Speed Steel ◽  
Growth Exponent ◽  
Force Microscopy ◽  
Tin Coatings ◽  
Atomic Force

TiN coatings with different thickness were prepared by arc ion plating (AIP) physical vapor deposition (PVD) on high speed steel (HSS) substrates. TiN coatings surface roughness was investigated by atomic force microscopy (AFM) and 3D optical profilometry and growth kinetics was described using scaling exponents β and α. The growth exponent β is 0.91-1.0 and the roughness exponent α is 0.77-0.81. Due to relatively high value of the exponent α, the surface diffusion is likely predominant smoothening mechanism of TiN growth.

MACRODROPLET REDUCTION AND GROWTH MECHANISMS IN CATHODIC ARC PHYSICAL VAPOR DEPOSITION OF TiN FILMS

2008 ◽  
Vol 15 (05) ◽  
pp. 653-659 ◽  
Author(s):  
MUBARAK ALI ◽  
ESAH HAMZAH ◽  
TAHIR ABBAS ◽  
MOHD RADZI HJ. MOHD TOFF ◽  
ISHTIAQ A. QAZI
Keyword(s):  
Vapor Deposition ◽  
Metal Ion ◽  
Physical Vapor Deposition ◽  
High Speed ◽  
Gas Flow ◽  
High Speed Steel ◽  
Hard Coatings ◽  
Growth Mechanisms ◽  
Tin Coatings ◽  
Cathodic Arc

Cathodic arc physical vapor deposition (CAPVD) a technique used for the deposition of hard coatings for tooling applications has many advantages. The main drawback of this technique is the formation of macrodroplets (MDs) during deposition resulting in films with rougher morphology. The MDs contamination and growth mechanisms was investigated in TiN coatings over high-speed steel, as a function of metal ion etching, substrate bias, and nitrogen gas flow rate; it was observed that the latter is the most important factor in controlling the size and number of the macrodroplets.

Experimental Analysis of Wear Mechanism and Tool Life in Dry Drilling of Al2024

2012 ◽  
Vol 566 ◽  
pp. 217-221 ◽  
Author(s):  
Ali Davoudinejad ◽  
Sina Alizadeh Ashrafi ◽  
Raja Ishak Raja Hamzah ◽  
Abdolkarim Niazi
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Wear Mechanisms ◽  
High Speed ◽  
Thrust Force ◽  
Cutting Speed ◽  
High Speed Steel ◽  
Dry Machining ◽  
Hole Quality ◽  
High Cutting Speed

Aluminum alloy is widely used in industry and various researches has been done on machiability of this material mainly due to its low weight and other superior properties. Dry machining is still interesting topic to reduce the cost of manufacturing and environmental contaminations. In present study dry machining of Al 2024 investigated on tool life, tool wear mechanisms, hole quality, thrust force and torque. Different types of high speed steel (HSS) tools utilized at constant feed rate of 0.04 mm/rev and cutting speeds within the range of 28 and 94 m/min. Experimental results revealed that HSCo drills, performed better than HSS drills in terms of tool life and hole quality. The main wear mechanisms which analyzed by scanning electron microscope found abrasive and adhesion wear on flank face, besides, BUE observed at chisel and cutting edges. However tool wear and BUE formation found more significant at high cutting speed. In terms of thrust force, two facet HSCo tools, recorded higher thrust force than four facet HSS drills.

Computerized Determination and Analysis of Cost and Production Rates for Machining Operations: Part 2—Milling, Drilling, Reaming, and Tapping

1969 ◽  
Vol 91 (3) ◽  
pp. 585-596 ◽  
Author(s):  
M. Field ◽  
N. Zlatin ◽  
R. Williams ◽  
M. Kronenberg
Keyword(s):  
Tool Life ◽  
High Speed ◽  
Cutting Speed ◽  
High Speed Steel ◽  
Production Rates ◽  
Optimum Cutting ◽  
The Cost ◽  
Machining Operations ◽  
Cutting Speeds ◽  
Minimum Costs

In Part 1 of this two-part paper, generalized equations for cost and production were presented for five major types of machining operations: turning, milling, drilling, reaming, and tapping. In addition, detailed cost equations were presented for the turning operation for three types of lathe tools: brazed carbide tools, throwaway tools, and solid high-speed steel tools. The present paper, Part 2, presents the detailed cost and production analysis for the remaining machining operations: milling, drilling, reaming, and tapping. Individual equations are developed within each machining category for the major types of cutters and tools involved in the operation. Examples are presented illustrating the use of these equations on specific problems. In addition, equations are developed for calculating the optimum cutting speeds and tool life corresponding to minimum costs and maximum production rates assuming that the tool life-cutting speed follows the simplified Taylor equation. The optimized equations enable one to interpolate and extrapolate the cost and production determinations. Care must be exercised to check experimentally the interpolated or extrapolated values to verify the results from the calculations.

scholarly journals Characterization of Tool Wear in High-Speed Milling of Hardened Powder Metallurgical Steels

2011 ◽  
Vol 2011 ◽  
pp. 1-13 ◽  
Author(s):  
Fritz Klocke ◽  
Kristian Arntz ◽  
Gustavo Francisco Cabral ◽  
Martin Stolorz ◽  
Marc Busch
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
High Speed ◽  
Cutting Speed ◽  
Thermal Characteristics ◽  
High Speed Steel ◽  
Vital Role ◽  
Cutting Performance ◽  
Cutting Length ◽  
Solid Carbide

In this experimental study, the cutting performance of ball-end mills in high-speed dry-hard milling of powder metallurgical steels was investigated. The cutting performance of the milling tools was mainly evaluated in terms of cutting length, tool wear, and cutting forces. Two different types of hardened steels were machined, the cold working steel HS 4-2-4 PM (K490 Microclean/66 HRC) and the high speed steel HS 6-5-3 PM (S790 Microclean/64 HRC). The milling tests were performed at effective cutting speeds of 225, 300, and 400 m/min with a four fluted solid carbide ball-end mill ( = 6, TiAlN coating). It was observed that by means of analytically optimised chipping parameters and increased cutting speed, the tool life can be drastically enhanced. Further, in machining the harder material HS 4-2-4 PM, the tool life is up to three times in regard to the less harder material HS 6-5-3 PM. Thus, it can be assumed that not only the hardness of the material to be machined plays a vital role for the high-speed dry-hard cutting performance, but also the microstructure and thermal characteristics of the investigated powder metallurgical steels in their hardened state.

Free Machining Steel: I—Tool-Life Characteristics of Resulfurized Steel

1961 ◽  
Vol 83 (2) ◽  
pp. 163-172 ◽  
Author(s):  
M. C. Shaw ◽  
N. H. Cook ◽  
P. A. Smith
Keyword(s):  
Sulfur Content ◽  
Tool Life ◽  
High Speed ◽  
Cold Work ◽  
Manganese Sulfide ◽  
Cutting Speed ◽  
High Speed Steel ◽  
Cutting Fluid ◽  
Low Sulfur Content ◽  
Hot Rolled

Tool-wear and tool-life characteristics of a series of five steels of different sulfur content are presented for different values of cutting speed, feed, cutting fluid, and cold work. While the presence of manganese sulfide in steel is generally found to extend tool life, certain combinations of speed and feed yield result that indicate the reverse effect. For the group of hot-rolled steels studied, sulfur was found to shorten tool life at certain cutting speeds when the feed was in the vicinity of 0.005 ipr. The hot-rolled steels of low sulfur content exhibit better tool life with high-speed steel tools than with carbide tools when the cutting speed is such as to give a tool life in the vicinity of 4 hr. A tracer device is described that is useful in exploring the nature and extent of the crater and built-up areas on the tool face.

The Influence of Copy Strategy on the Tool Life of Ball End Mills and Achieved Surface Roughness

2016 ◽  
Vol 686 ◽  
pp. 240-245
Author(s):  
Tomáš Vopát ◽  
Jozef Peterka ◽  
Vladimír Šimna ◽  
Ivan Buranský
Keyword(s):  
Surface Roughness ◽  
Tool Life ◽  
High Speed ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Tool Material ◽  
High Speed Steel ◽  
Depth Of Cut ◽  
Radial Depth ◽  
End Mills

The article deals with the tool life of ball nose end mills and surface roughness of steel C45 depending on up-copying and down-copying. The cemented carbide and high speed steel was used as tool material. Furthermore, the new and sharpened cutting tools were also compared. In the experiment, the cutting speed, feed rate, axial and radial depth of cut were not changed. The results show different achieved surface roughness of machined material C45 and tool life of ball nose end mills depending on the copy milling strategy for various tool materials.

Research on Cutting Performance of HSS Taps by Electric Enhanced

2012 ◽  
Vol 251 ◽  
pp. 402-405
Author(s):  
Hui Wang ◽  
Feng Zhou ◽  
Rong Di Han ◽  
Yong Hong Liu
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
High Speed ◽  
Production Efficiency ◽  
High Speed Steel ◽  
Cutting Edge ◽  
Edge Region ◽  
Edge Strength ◽  
Tool Edge ◽  
Increase Tool Life

After tool edges sharpen, there are a variety of micro-defects in the area of edge, which will accelerate tool wear and shorten tool life. In order to increase tool life and production efficiency, the area of edge strengthen was needed. In this paper, the electrolysis technology was used to enhance the cutting edge of high-speed steel(HSS) tap, the rounding of the edge region of the forming edge and surface morphology of cutting edge were investigated. And the tapping tests were carried on the Ti6Al4V. The results showed that electrolysis enhanced technology can eliminate the defects, invert a circular edge and improve the tool edge strength. The original tap was worn rapidly in the early stages of wear and the cutting force was changed big variation. The results showed that tap strengthened can reduce tool wear and improve tool life.

Sign in / Sign up

Export Citation Format

Share Document