scholarly journals High-Sensitivity Biosensor Based on Glass Resonance PhC Cavities for Detection of Blood Component and Glucose Concentration in Human Urine

Coatings ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 1555
Author(s):  
Abduladheem Turki Jalil ◽  
Shameen Ashfaq ◽  
Dmitry Olegovich Bokov ◽  
Amer M. Alanazi ◽  
Kadda Hachem ◽  
...  
Keyword(s):  
Human Urine ◽  
Glucose Concentration ◽  
Free Spectral Range ◽  
High Sensitivity ◽  
Optical Biosensor ◽  
Optical Signal ◽  
Blood Component ◽  
Detection Accuracy ◽  
Worst Case ◽  
Detection Range

In this work, a novel structure of an all-optical biosensor based on glass resonance cavities with high detection accuracy and sensitivity in two-dimensional photon crystal is designed and simulated. The free spectral range in which the structure performs well is about FSR = 630 nm. This sensor measures the concentration of glucose in human urine. Analyses to determine the glucose concentration in urine for a normal range (0~15 mg/dL) and urine despite glucose concentrations of 0.625, 1.25, 2.5, 5 and 10 g/dL in the wavelength range 1.326404~1.326426 μm have been conducted. The detection range is RIU = 0.2 × 10−7. The average bandwidth of the output resonance wavelengths is 0.34 nm in the lowest case. In the worst case, the percentage of optical signal power transmission is 77% with an amplitude of 1.303241 and, in the best case, 100% with an amplitude of 1.326404. The overall dimensions of the biosensor are 102.6 µm2 and the sensitivity is equal to S = 1360.02 nm/RIU and the important parameter of the Figure of Merit (FOM) for the proposed biosensor structure is equal to FOM = 1320.23 RIU−1.

scholarly journals Ratiometric Fluorescent Biosensors for Glucose and Lactate Using an Oxygen-Sensing Membrane

Biosensors ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 208
Author(s):  
Hong Dinh Duong ◽  
Jong Il Rhee
Keyword(s):  
Limit Of Detection ◽  
Oxygen Sensing ◽  
High Sensitivity ◽  
Glucose Sensing ◽  
Oxidation Reactions ◽  
Lactate Oxidase ◽  
Lactate Oxidation ◽  
Detection Range ◽  
Quenching Effect ◽  
Sensing Membrane

In this study, ratiometric fluorescent glucose and lactate biosensors were developed using a ratiometric fluorescent oxygen-sensing membrane immobilized with glucose oxidase (GOD) or lactate oxidase (LOX). Herein, the ratiometric fluorescent oxygen-sensing membrane was fabricated with the ratio of two emission wavelengths of platinum meso-tetra (pentafluorophenyl) porphyrin (PtP) doped in polystyrene particles and coumarin 6 (C6) captured into silica particles. The operation mechanism of the sensing membranes was based on (i) the fluorescence quenching effect of the PtP dye by oxygen molecules, and (ii) the consumption of oxygen levels in the glucose or lactate oxidation reactions under the catalysis of GOD or LOX. The ratiometric fluorescent glucose-sensing membrane showed high sensitivity to glucose in the range of 0.1–2 mM, with a limit of detection (LOD) of 0.031 mM, whereas the ratiometric fluorescent lactate-sensing membrane showed the linear detection range of 0.1–0.8 mM, with an LOD of 0.06 mM. These sensing membranes also showed good selectivity, fast reversibility, and stability over long-term use. They were applied to detect glucose and lactate in artificial human serum, and they provided reliable measurement results.

A rapid and accurate method for screening T-2 toxin in food and feed using competitive AlphaLISA

2021 ◽  
Vol 368 (6) ◽  
Author(s):  
Liwen Zhang ◽  
Qingyu Lv ◽  
Yuling Zheng ◽  
Xuan Chen ◽  
Decong Kong ◽  
...  
Keyword(s):  
High Sensitivity ◽  
Accurate Method ◽  
Detection Methods ◽  
Cereal Crops ◽  
Detection Range ◽  
Highly Sensitive ◽  
Food And Feed ◽  
Good Repeatability ◽  
Feed Samples ◽  
Better Than

ABSTRACT T-2 is a common mycotoxin contaminating cereal crops. Chronic consumption of food contaminated with T-2 toxin can lead to death, so simple and accurate detection methods in food and feed are necessary. In this paper, we establish a highly sensitive and accurate method for detecting T-2 toxin using AlphaLISA. The system consists of acceptor beads labeled with T-2-bovine serum albumin (BSA), streptavidin-labeled donor beads and biotinylated T-2 antibodies. T-2 in the sample matrix competes with T-2-BSA for antibodies. Adding biotinylated antibodies to the test well followed by T-2 and T-2-BSA acceptor beads yielded a detection range of 0.03–500 ng/mL. The half-maximal inhibitory concentration was 2.28 ng/mL and the coefficient of variation was <10%. In addition, this method had no cross-reaction with other related mycotoxins. This optimized method for extracting T-2 from food and feed samples achieved a recovery rate of approximately 90% in T-2 concentrations as low as 1 ng/mL, better than the performance of a commercial ELISA kit. This competitive AlphaLISA method offers high sensitivity, good specificity, good repeatability and simple operation for detecting T-2 toxin in food and feed.

Development of an Optical Fiber Sensor with a D-shaped Fiber Bragg Grating Integrated in a Loop-mirror Optical Fiber Laser as a High Sensitivity Refractometer

2021 ◽  
Vol 32 ◽  
Author(s):  
Binh Pham Thanh ◽  
Thuy Van Nguyen ◽  
Van Hoi Pham ◽  
Huy Bui ◽  
Thi Hong Cam Hoang ◽  
...  
Keyword(s):  
Refractive Index ◽  
Optical Fiber ◽  
Fiber Laser ◽  
Fiber Bragg Grating ◽  
Limit Of Detection ◽  
Optical Fiber Sensor ◽  
High Sensitivity ◽  
Optical Signal ◽  
Bragg Grating ◽  
Loop Mirror

In this paper, we report a new type of refractometer based on a D-shaped fiber Bragg grating (FBG) integrated in a loop-mirror optical fiber laser. This proposed sensor is used in wavelength interrogation method, in which the D-shaped FBG is applied as a refractive index (RI) sensing probe and a mirror to select mode of laser. The D-shaped FBG is prepared by the removal of a portion of the fiber cladding covering the FBG by means of side-polishing technique. The D-shaped FBG sensing probe integrated in a loop-mirror optical fiber laser with saturated pump technique, the characteristics of sensing signals have been improved to obtain stable intensity, narrower bandwidth and higher optical signal-to-noise ratio compare to normal reflection configuration. The limit of detection (LOD) of this sensor can be achieved to 2.95 x 10-4 RIU in the refractive index (RI) range of 1.42-1.44. Accordingly, we believe that the proposed refractometer has a huge potential for applications in biochemical-sensing technique.

Glucose concentration determination based on silica sol–gel encapsulated glucose oxidase optical biosensor arrays

Talanta ◽  
2010 ◽  
Vol 83 (1) ◽  
pp. 61-65 ◽  
Author(s):  
Gang Chang ◽  
Yoshiro Tatsu ◽  
Tatsushi Goto ◽  
Hiromasa Imaishi ◽  
Kenichi Morigaki
Keyword(s):  
Glucose Oxidase ◽  
Glucose Concentration ◽  
Sol Gel ◽  
Optical Biosensor ◽  
Silica Sol ◽  
Biosensor Arrays ◽  
Concentration Determination

Specific Detection of Staphylococcus Enterotoxin B in Milk Using Piezoresistive Cantilever Aptasensor

2015 ◽  
Vol 645-646 ◽  
pp. 1298-1302
Author(s):  
Rui Zhao ◽  
Yong Zheng Wen ◽  
Wei Ma ◽  
Jian Cheng Yang ◽  
Xiao Mei Yu
Keyword(s):  
High Sensitivity ◽  
Rapid Response ◽  
Experimental Results ◽  
Quick Response ◽  
Specific Detection ◽  
Detection Range ◽  
Coated Surface ◽  
Enterotoxin B ◽  
Food Commodities ◽  
Staphylococcus Enterotoxin B

In this paper, an aptasensor with high sensitivity and rapid response was developed for the detection of staphylococcus enterotoxin B (SEB) by using thiol-modified piezoresistive cantilever. Thiol-modified aptamers, acting as the functionalized sensing elements, were immobilized on the nanogold-coated surface of the sensing cantilever as agents for detecting SEB. By using the functionalized aptasensors, different concentrations of SEB were detected with a wide detection range of 6-100 ng/mL and a quick response in milk. The experimental results indicated that the cantilever-based aptasensors had sufficient sensitivity for the detection of SEB in real food commodities and might provide an economical platform for on-site detections of different toxicants with the advantages of portability, high sensitivity, and rapid response.

scholarly journals Portable smartphone-integrated paper sensors for fluorescence detection of As(III) in groundwater

2020 ◽  
Vol 7 (12) ◽  
pp. 201500
Author(s):  
Sha Liu ◽  
Yong Li ◽  
Chao Yang ◽  
Liqiang Lu ◽  
Yulun Nie ◽  
...  
Keyword(s):  
Environmental Problem ◽  
Visual Detection ◽  
High Sensitivity ◽  
Integration System ◽  
Detection Range ◽  
Sensitivity And Selectivity ◽  
Toxic Metalloid ◽  
Interfering Ions ◽  
Cu Nanoclusters

Arsenic contamination in groundwater is a supreme environmental problem, and levels of this toxic metalloid must be strictly monitored by a portable, sensitive and selective analytical device. Herein, a new system of smartphone-integrated paper sensors with Cu nanoclusters was established for the effective detection of As(III) in groundwater. For the integration system, the fluorescence emissive peak of Cu nanoclusters at 600 nm decreased gradually with increasing As(III) addition. Meanwhile, the fluorescence colour also changed from orange to colourless, and the detection limit was determined as 2.93 nM (0.22 ppb) in a wide detection range. The interfering ions also cannot influence the detection selectivity of As(III). Furthermore, the portable paper sensors based on Cu nanoclusters were fabricated for visual detection of As(III) in groundwater. The quantitative determination of As(III) in natural groundwater has also been accomplished with the aid of a common smartphone. Our work has provided a portable and on-site detection technique toward As(III) in groundwater with high sensitivity and selectivity.

scholarly journals Wearable Pressure Sensors Based on Carbonized Graphene Coated Waste Paper Aerogel

2021 ◽  
Author(s):  
Ang Li ◽  
Ce Cui ◽  
Weijie Wang ◽  
Yue Zhang ◽  
Jianyu Zhai ◽  
...  
Keyword(s):  
3D Structure ◽  
Pressure Sensors ◽  
High Sensitivity ◽  
Waste Paper ◽  
Low Density ◽  
Detection Range ◽  
Simple Strategy ◽  
Simple Filtration ◽  
Piezoresistive Pressure Sensors ◽  
Main Component

Abstract Graphene is complexed with cellulose fibers to construct 3D aerogels, which is generally considered to be an environmentally friendly and simple strategy to achieve wide sensing, high sensitivity and low detection of wearable piezoresistive pressure sensors. Here, graphene is incorporated into waste paper fibers with cellulose as the main component to prepare graphene coated waste paper aerogel (GWA) using a simple “filtration-oven drying” method under atmospheric pressure. The GWA was further annealed to obtain the carbonized graphene coated waste paper aerogel (C-GWA) to achieve low density and excellent resilience. The result shows that the C-GWA has a rough outer surface due to the 3D structure formed by interpenetrated fibers and the carbon skeleton with wrinkles. The sensor based on GCA shows low density (25mg/cm3), a wide detection range of 0-132 kPa, an ultra-low detection limit of 2.5 Pa (a green bean, ≈ 53.4 mg), and a high sensitivity of 31.6 kPa− 1. In addition, the sensor based on C-GWA with the excellent performance can be used to detect human motions including the pulse of the human body, cheek blowing and bending of human joints. The result indicates that the sensor based on C-GWA shows great potential for wearable electronic products.

scholarly journals A dual electro-optical biosensor based on Chlamydomonas reinhardtii immobilised on paper-based nanomodified screen-printed electrodes for herbicide monitoring

2021 ◽  
Author(s):  
Amina Antonacci ◽  
Raouia Attaallah ◽  
Fabiana Arduini ◽  
Aziz Amine ◽  
Maria Teresa Giardi ◽  
...  
Keyword(s):  
Chlamydomonas Reinhardtii ◽  
High Sensitivity ◽  
Optical Biosensor ◽  
Whole Cells ◽  
Screen Printed Electrodes ◽  
And Storage ◽  
High Repeatability ◽  
High Sensitivity Detection ◽  
Screen Printed

Abstract The indiscriminate use of herbicides in agriculture contributes to soil and water pollution, with important endangering consequences on the ecosystems. Among the available analytical systems, algal biosensors have demonstrated to be valid tools thanks to their high sensitivity, cost-effectiveness, and eco-design. Herein, we report the development of a dual electro-optical biosensor for herbicide monitoring, based on Chlamydomonas reinhardtii whole cells immobilised on paper-based screen-printed electrodes modified with carbon black nanomaterials. To this aim, a systematic study was performed for the selection and characterisation of a collection among 28 different genetic variants of the alga with difference response behaviour towards diverse herbicide classes. Thus, CC125 strain was exploited as case study for the study of the analytical parameters. The biosensor was tested in standard solutions and real samples, providing high sensitivity (detection limit in the pico/nanomolar), high repeatability (RSD of 5% with n = 100), long lasting working (10 h) and storage stability (3 weeks), any interference in the presence of heavy metals and insecticides, and low matrix effect in drinking water and moderate effect in surface one.

Sign in / Sign up

Export Citation Format

Share Document