scholarly journals Hamiltonian Modeling and Structure Modified Control of Diesel Engine

Energies ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 2011
Author(s):  
Jing Qian ◽  
Yakun Guo ◽  
Yidong Zou ◽  
Shige Yu

A diesel engine is a typical dynamic system. In this paper, a dynamics method is proposed to establish the Hamiltonian model of the diesel engine, which solves the main difficulty of constructing a Hamiltonian function under the multi-field coupling condition. Furthermore, the control method of Hamiltonian model structure modification is introduced to study the control of a diesel engine. By means of the principle of energy-shaping and Hamiltonian model structure modification theories, the modified energy function is constructed, which is proved to be a quasi-Lyapunov function of the closed-loop system. Finally, the control laws are derived, and the simulations are carried out. The study reveals the dynamic mechanism of diesel engine operation and control and provides a new way to research the modeling and control of a diesel engine system.

2016 ◽  
Vol 4 (2) ◽  
pp. 1-16
Author(s):  
Ahmed S. Khusheef

 A quadrotor is a four-rotor aircraft capable of vertical take-off and landing, hovering, forward flight, and having great maneuverability. Its platform can be made in a small size make it convenient for indoor applications as well as for outdoor uses. In model there are four input forces that are essentially the thrust provided by each propeller attached to each motor with a fixed angle. The quadrotor is basically considered an unstable system because of the aerodynamic effects; consequently, a close-loop control system is required to achieve stability and autonomy. Such system must enable the quadrotor to reach the desired attitude as fast as possible without any steady state error. In this paper, an optimal controller is designed based on a Proportional Integral Derivative (PID) control method to obtain stability in flying the quadrotor. The dynamic model of this vehicle will be also explained by using Euler-Newton method. The mechanical design was performed along with the design of the controlling algorithm. Matlab Simulink was used to test and analyze the performance of the proposed control strategy. The experimental results on the quadrotor demonstrated the effectiveness of the methodology used.


Robotica ◽  
2005 ◽  
Vol 24 (2) ◽  
pp. 229-237 ◽  
Author(s):  
Jae H. Chung ◽  
Changhoon Kim

This paper discusses the modeling and control of a robotic manipulator with a new deburring tool, which integrates two pneumatic actuators to take advantage of a double cutting action. A coordination control method is developed by decomposing the robotic deburring system into two subsystems; the arm and the deburring tool. A decentralized control approach is pursued, in which suitable controllers were designed for the two subsystems in the coordination scheme. In simulation, three different tool configurations are considered: rigid, single pneumatic and integrated pneumatic tools. A comparative study is performed to investigate the deburring performance of the deburring arm with the different tools. Simulation results show that the developed robotic deburring system significantly improves the accuracy of the deburring operation.


2020 ◽  
Vol 7 (1) ◽  
pp. 10-18
Author(s):  
Songcen Wang ◽  
Xiaokang Wu ◽  
Ying Yang ◽  
Cong Zhu ◽  
Zhen Wu ◽  
...  

AbstractAiming at the influence of coupling coefficient variation on the output voltage of a high-power LCC-S topology inductively coupled power transfer (ICPT) system, a synchronous three-phase triple-parallel Buck converter is used as the voltage adjustment unit. The control method for the three-phase current sharing of synchronous three-phase triple-parallel Buck converter and the constant voltage output ICPT system under the coupling coefficient variation is studied. Firstly, the hybrid model consisting of the circuit averaging model of the three-phase triple-parallel Buck converter and the generalized state-space average model for the LCC-S type ICPT system is established. Then, the control methods for three-phase current sharing of the synchronous three-phase triple-parallel Buck converter and constant voltage output of ICPT system are studied to achieve the multi-objective integrated control of the system. Finally, a 3.3 kW wireless charging system platform is built, the experimental results have verified the effectiveness of the proposed modeling and control method, and demonstrated the stability of the ICPT system.


Robotica ◽  
1998 ◽  
Vol 16 (6) ◽  
pp. 607-613 ◽  
Author(s):  
J. H. Chung ◽  
S. A. Velinsky

This paper concerns the modeling and control of a mobile manipulator which consists of a robotic arm mounted upon a mobile platform. The equations of motion are derived using the Lagrange-d'Alembert formulation for the nonholonomic model of the mobile manipulator. The dynamic model which considers slip of the platform's tires is developed using the Newton-Euler method and incorporates Dugoff's tire friction model. Then, the tracking problem is investigated by using a well known nonlinear control method for the nonholonomic model. The adverse effect of the wheel slip on the tracking of commanded motion is discussed in the simulation. For the dynamic model, a variable structure control approach is employed to minimize the harmful effect of the wheel slip on the tracking performance. The simulation results demonstrate the effectiveness of the proposed control algorithm.


Author(s):  
Takuya Nomoto ◽  
Daisuke Hunakoshi ◽  
Toru Watanabe ◽  
Kazuto Seto

This paper presents a new modeling method and a control system design procedure for a flexible rotor with many elastic modes using active magnetic bearings. The purpose of our research is to let the rotor rotate passing over the 1st and the 2nd critical speeds caused by flexible modes. To achieve this, it is necessary to control motion and vibration of the flexible rotor simultaneously. The new modeling method named as Extended Reduced Order Physical Model is presented to express its motion and vibration uniformly. By using transfer function of flexible rotor-Active Magnetic Bearings system, we designed a Local Jerk Feedback Control system and conducted stability discrimination with root locus. In order to evaluate this modeling and control method, levitation experimentation is conducted.


2012 ◽  
Vol 212-213 ◽  
pp. 1043-1047
Author(s):  
Tian Mao Xu ◽  
Li Xiang Zhang ◽  
Yun Zeng ◽  
Jing Qian

In this paper, nonlinear turbine model and hydraulic system which is one penstock one machine dynamic differential equation with elastic water column are combined. Hamiltonian function of hydraulic turbine is constructed. By applying Hamiltonian orthogonal decomposition realization and dissipation realization method, generalized Hamiltonian model of hydraulic turbine is built. Connected with generator third-order Hamiltonian model of single machine infinite bus system, generalized Hamiltonian model of hydraulic generator unit is established. This paper provides certain theory basis for research operation and control dynamics mechanism of hydraulic generator unit in generalized Hamiltonian system framework.


2010 ◽  
Vol 97-101 ◽  
pp. 3682-3685
Author(s):  
Hai Wei Wang ◽  
Geng Liu ◽  
Dang Dang Zheng

According to the simulation requirement for complex mechanical system, building flow modeling and control mechanism is the main content of development for the collaborative simulation platform. Based on research and analysis to WFCP-Net technique, we present multi-layer distributed flow. Management flow and simulation flow are defined, and a suit of entity class model and a kind of flow control mechanism are designed. Finally, the method is verified by the platform developed.


Sign in / Sign up

Export Citation Format

Share Document