scholarly journals Design Optimization of a Dual-Bleeding Recirculation Channel to Enhance Operating Stability of a Transonic Axial Compressor

Energies ◽  
2021 ◽  
Vol 15 (1) ◽  
pp. 159
Author(s):  
Tien-Dung Vuong ◽  
Kwang-Yong Kim
Keyword(s):  
Design Optimization ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Aerodynamic Performance ◽  
Maximum Pressure ◽  
Stall Margin ◽  
Design Variables ◽  
Operating Stability ◽  
Transonic Axial Compressor

The present work performed a comprehensive investigation to find the effects of a dual-bleeding port recirculation channel on the aerodynamic performance of a single-stage transonic axial compressor, NASA Stage 37, and optimized the channel’s configuration to enhance the operating stability of the compressor. The compressor’s performance was examined using three parameters: The stall margin, adiabatic efficiency, and pressure ratio. Steady-state three-dimensional Reynolds-averaged Navier–Stokes analyses were performed to find the flow field and aerodynamic performance. The results showed that the addition of a bleeding channel increased the recirculation channel’s stabilizing effect compared to the single-bleeding channel. Three design variables were selected for optimization through a parametric study, which was carried out to examine the influences of six geometric parameters on the channel’s effectiveness. Surrogate-based design optimization was performed using the particle swarm optimization algorithm coupled with a surrogate model based on the radial basis neural network. The optimal design was found to increase the stall margin by 51.36% compared to the case without the recirculation channel with only 0.55% and 0.28% reductions in the peak adiabatic efficiency and maximum pressure ratio, respectively.

Parametric Study on Aerodynamic Performance of a Transonic Axial Compressor with a Casing Groove and Tip Injection

2013 ◽  
Vol 284-287 ◽  
pp. 872-877 ◽  
Author(s):  
Dae Woong Kim ◽  
Jin Hyuk Kim ◽  
Kwang Yong Kim
Keyword(s):  
Parametric Study ◽  
Stokes Equations ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Aerodynamic Performance ◽  
Navier Stokes ◽  
Stall Margin ◽  
Transonic Axial Compressor ◽  
Tip Injection

This paper presents a parametric study on aerodynamic performance of a transonic axial compressor combined with a casing groove and tip injection using three-dimensional Reynolds-average Navier-Stokes equations. The front and rear lengths and height of the groove are selected as the geometric parameters to investigate their effects on the stall margin and peak adiabatic efficiency. These parameters are changed with constant injection. The validation of the numerical results is performed in comparison with experimental data for the total pressure ratio and adiabatic efficiency. As the results of the parametric study, the maximum stall margin and peak adiabatic efficiency are obtained in the axial compressor having 70% groove height of the reference groove. The stall margin and peak adiabatic efficiency in other cases are also improved in comparison with the axial compressors with the smooth casing and reference groove. The results show that both the stall margin and the peak adiabatic efficiency are considerably improved by the application of the casing groove combined with tip injection in an axial compressor.

Design Optimization of Circumferential Casing Grooves for a Transonic Axial Compressor to Enhance Stall Margin

2010 ◽  
Author(s):  
Kwang-Jin Choi ◽  
Jin-Hyuk Kim ◽  
Kwang-Yong Kim
Keyword(s):  
Design Optimization ◽  
Numerical Solutions ◽  
Stokes Equations ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Latin Hypercube Sampling ◽  
Optimum Shape ◽  
Data Set ◽  
Stall Margin

This paper presents a design optimization of an axial compressor with NASA Rotor 37 and five circumferential casing grooves for enhancement of stall margin. Three-dimensional Reynolds-averaged Navier-Stokes equations with the shear stress transport turbulence model are discretized by finite volume approximations and solved on hexahedral grids for the flow analyses. The validation of the numerical results is performed in comparison with experimental data for pressure ratio and adiabatic efficiency. The Latin-hypercube sampling as design-of-experiments is used to generate the twelve design points within the design space. A stall margin parameter is considered as an objective function with two design variables defining the geometry of the circumferential casing grooves. The radial basis neural network method employed as a surrogate model for the design optimization of the circumferential casing grooves is trained on the numerical solutions by carrying out leave-one-out cross-validation for the data set. The results show that the stall margin of the optimum shape is enhanced considerably by the design optimization compared to the cases with smooth casing and the reference grooves.

AERODYNAMIC PERFORMANCE OF AN AXIAL COMPRESSOR WITH A CASING GROOVE COMBINED WITH INJECTION

2013 ◽  
Vol 37 (3) ◽  
pp. 283-292 ◽  
Author(s):  
Dae-Woong Kim ◽  
Jin-Hyuk Kim ◽  
Kwang-Yong Kim
Keyword(s):  
Turbulence Model ◽  
Parametric Study ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Aerodynamic Performance ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Stall Margin ◽  
Transonic Axial Compressor

Aerodynamic performance of a transonic axial compressor with a casing groove combined with injection has been investigated in this work. Three-dimensional Reynolds-averaged Navier–Stokes equations with k-ε turbulence model are discretized by finite volume approximations and solved on hexahedral grids for the flow analyses. For parametric study, the front and rear lengths and height of the casing groove are selected as the geometric parameters and are changed with constant injection to investigate their effects on the stall margin and peak adiabatic efficiency. As a result of the parametric study, the maximum stall margin and peak adiabatic efficiency are found to be obtained in the axial compressor having 70% height of the reference groove. The results show that the application of the casing groove combined with injection to an axial compressor is effective for the simultaneous improvement of both the stall margin and peak adiabatic efficiency of the compressor.

scholarly journals Stability Enhancement of a Single-Stage Transonic Axial Compressor Using Inclined Oblique Slots

Energies ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2346
Author(s):  
Tien-Dung Vuong ◽  
Kwang-Yong Kim
Keyword(s):  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Single Stage ◽  
Rotor Blades ◽  
Navier Stokes ◽  
Optimized Design ◽  
Stall Margin ◽  
Casing Treatment ◽  
Transonic Axial Compressor

A casing treatment using inclined oblique slots (INOS) is proposed to improve the stability of the single-stage transonic axial compressor, NASA Stage 37, during operation. The slots are installed on the casing of the rotor blades. The aerodynamic performance was estimated using three-dimensional steady Reynolds-Averaged Navier-Stokes analysis. The results showed that the slots effectively increased the stall margin of the compressor with slight reductions in the pressure ratio and adiabatic efficiency. Three geometric parameters were tested in a parametric study. A single-objective optimization to maximize the stall margin was carried out using a Genetic Algorithm coupled with a surrogate model created by a radial basis neural network. The optimized design increased the stall margin by 37.1% compared to that of the smooth casing with little impacts on the efficiency and pressure ratio.

Effects of stator splitter blades on aerodynamic performance of a single-stage transonic axial compressor

2020 ◽  
Vol 14 (4) ◽  
pp. 7369-7378
Author(s):  
Ky-Quang Pham ◽  
Xuan-Truong Le ◽  
Cong-Truong Dinh
Keyword(s):  
Stokes Equations ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Aerodynamic Performance ◽  
Numerical Results ◽  
Single Stage ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Operating Stability ◽  
Length Coverage

Splitter blades located between stator blades in a single-stage axial compressor were proposed and investigated in this work to find their effects on aerodynamic performance and operating stability. Aerodynamic performance of the compressor was evaluated using three-dimensional Reynolds-averaged Navier-Stokes equations using the k-e turbulence model with a scalable wall function. The numerical results for the typical performance parameters without stator splitter blades were validated in comparison with experimental data. The numerical results of a parametric study using four geometric parameters (chord length, coverage angle, height and position) of the stator splitter blades showed that the operational stability of the single-stage axial compressor enhances remarkably using the stator splitter blades. The splitters were effective in suppressing flow separation in the stator domain of the compressor at near-stall condition which affects considerably the aerodynamic performance of the compressor.

Numerical Investigation on the Effect of Bleed Port With Self-Recirculating Casing Treatment on the Stability of a 1.5-Stage Transonic Compressor

2019 ◽  
Author(s):  
Yiming Zhong ◽  
WuLi Chu ◽  
HaoGuang Zhang
Keyword(s):  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Stability Margin ◽  
Axial Position ◽  
Stable Operation ◽  
Stall Margin ◽  
Casing Treatment ◽  
Transonic Compressor ◽  
Compressor Efficiency

Abstract Compared to the traditional casing treatment, the self-recirculating casing treatment (SCT) can improve or not decrease the compressor efficiency while achieving the stall margin improvement. For the bleed port, the main design indicator is to reduce the flow loss caused by suction, while providing sufficient jet flow and jet pressure to the injector. In order to gain a better study of the bleed port stabilization mechanisms, the bleed configuration was parameterized with the bleed port inlet width and the bleed port axial position. Five kinds of recirculating casing treatments were applied to a 1.5-stage transonic axial compressor with the method of three-dimensional unsteady numerical simulation. Fifteen identical self-recirculating devices are uniformly mounted around the annulus. The numerical results show that the SCT can improve compressor total pressure ratio and stability, shift the stall margin towards lower mass flows. Furthermore, it has no impact on compressor efficiency. The optimal case presents that stability margin is improved by 6.7% employing 3.1% of the annulus mass flow. Expanding bleed port inlet width to an intermediate level can further enhance compressor stability, but excessive bleed port inlet width will reduce the stabilization effect. The optimal bleed port position is located in the blocked area of the low energy group at the top of the rotor. In the case of solid casing, stall inception was the tip blockage, which was mainly triggered by the interaction of the tip leakage vortex and passage shock. From radial distribution, the casing treatment predominantly affects the above 70% span. The reduction of tip reflux region by suction effect is the main reason for the extension of stable operation range. The SCT also has an obvious stability improvement in tip blockage stall, while delaying the occurrence of compressor stall.

Design Optimization of a Single-Stage Transonic Axial Compressor and Test Evaluation of Its Aerodynamic Performance

2012 ◽  
Vol 15 (6) ◽  
pp. 77-84 ◽  
Author(s):  
Tae Choon Park ◽  
Young-Seok Kang ◽  
Oh-Sik Hwang ◽  
Ji-Han Song ◽  
Byeung Jun Lim
Keyword(s):  
Design Optimization ◽  
Axial Compressor ◽  
Aerodynamic Performance ◽  
Single Stage ◽  
Test Evaluation ◽  
Transonic Axial Compressor

Effect of Trailing Edge Crenulation on the Performance and Stall Margin of a Transonic Axial Compressor

2013 ◽  
Author(s):  
S. Subbaramu ◽  
Quamber H. Nagpurwala ◽  
A. T. Sriram
Keyword(s):  
Beneficial Effect ◽  
Total Pressure ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Compressor Cascade ◽  
Trailing Edge ◽  
Stall Margin ◽  
Positive Effects ◽  
Compressor Rotor ◽  
Transonic Axial Compressor

This paper deals with the numerical investigations on the effect of trailing edge crenulation on the performance of a transonic axial compressor rotor. Crenulation is broadly considered as a series of small notches or slots at the edge of a thin object, like a plate. Incorporating such notches at the trailing edge of a compressor cascade has shown beneficial effect in terms of reduction in total pressure loss due to enhanced mixing in the wake region. These notches act as vortex generators to produce counter rotating vortices, which increase intermixing between the free stream flow and the low momentum wake fluid. Considering the positive effects of crenulation in a cascade, it was hypothesized that the same technique would work in a rotating compressor to enhance its performance and stall margin. However, the present CFD simulations on a transonic compressor rotor have given mixed results. Whereas the peak total pressure ratio in the presence of trailing edge crenulation reduced, the stall margin improved by 2.97% compared to the rotor with straight edge blades. The vortex generation at the crenulated trailing edge was not as strong as reported in case of linear compressor cascade, but it was able to influence the flow field in the rotor tip region so as to energize the low momentum end-wall flow in the aft part of the blade passage. This beneficial effect delayed flow separation and allowed the mass flow rate to be reduced to still lower levels resulting in improved stall margin. The reduction in pressure ratio with crenulation was surprising and might be due to increased mixing losses downstream of the blade.

Effect of Backward Sweep on Aerodynamic Performance of a 1.5-Stage Highly Loaded Axial Compressor

2020 ◽  
Author(s):  
Song Huang ◽  
Chuangxin Zhou ◽  
Chengwu Yang ◽  
Shengfeng Zhao ◽  
Mingyang Wang ◽  
...  
Keyword(s):  
Total Pressure ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Aerodynamic Performance ◽  
Blade Loading ◽  
Stall Margin ◽  
Axial Compressors ◽  
Design Speed ◽  
Total Pressure Ratio ◽  
Highly Loaded

Abstract As a degree of freedom in the three-dimensional blade design of axial compressors, the sweep technique significantly affects the aerodynamic performance of axial compressors. In this paper, the effects of backward sweep rotor configurations on the aerodynamic performance of a 1.5-stage highly loaded axial compressor at different rotational design speeds are studied by numerical simulation. The aim of this work is to improve understanding of the flow mechanism of backward sweep on the aerodynamic performance of a highly loaded axial compressor. A commercial CFD package is employed for flow simulations and analysis. The study found that at the design rotational speed, compared with baseline, backward sweep rotor configurations reduce the blade loading near the leading edge but slightly increases the blade loading near the trailing edge in the hub region. As the degree of backward sweep increases, the stall margin of the 1.5-stage axial compressor increase first and then decrease. Among different backward sweep rotor configurations, the 10% backward sweep rotor configuration has the highest stall margin, which is about 2.5% higher than that of baseline. This is due to the change of downstream stator incidence, which improves flow capacity near the hub region. At 80% rotational design speed, backward sweep rotor configurations improve stall margin and total pressure ratio of the compressor. It’s mainly due to the decreases of the rotor incidence near the middle span, which results in the decreases of separation on the suction surface. At 60% rotational design speed, detached shock disappears. Backward sweep rotor configurations deteriorate stall margin of the compressor, but increase total pressure ratio and adiabatic efficiency when the flow rate is lower than that at peak efficiency condition. Therefore, it’s necessary to consider the flow field structure of axial compressors at whole operating conditions in the design process and use the design freedom of sweep to improve the aerodynamic performance.

CFD Code Validation and Qualitative Study of Effects of Tip Clearance Variation on Performance of Transonic Axial Compressor Rotor

2012 ◽  
Author(s):  
Aniket R. Patkar ◽  
Srinivethan Rangasamy ◽  
Sreekanth Raghunath ◽  
Vilas Kalamkar
Keyword(s):  
Pressure Ratio ◽  
Splitting Method ◽  
Flow Characteristics ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Maximum Pressure ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Transonic Axial Compressor ◽  
Multiple Frame

The main objective of this work is the validation of Computational Fluid Dynamics (CFD) code used for analysis of transonic axial compressors. NASA Rotor 35 is used here as test case for validation. In this work, computations are performed using parallelized RANS code, to predict the transonic axial compressor rotor flow characteristics. Advection Upstream Splitting Method (AUSM) scheme has been used. A Multiple Frame of Reference approach has been used to model the rotor passage. Spalart-Allmaras turbulence model is used to model turbulence. Multiblock Structured mesh is used. Performance characteristics for the entire range of operation, from maximum mass flow rate till maximum pressure ratio, have been simulated. The results obtained are comparable with experimental data within 5–10% error. Investigations have been carried out to study the effect of varying tip clearance in NASA Rotor 35. The present work is intended to study the clearance flow trajectory as a function of varying tip clearance. The effects of shock/vortex interaction in tip clearance region are also studied. The effects of tip clearance size on the generation and evolution of the end-wall vortical structures are discussed by investigating their evolutionary trajectories. By this study, it is observed that as tip clearance reduces, clearance flow trajectory moves downstream. From this it can be concluded that if tip clearance increases, tip clearance vortices expand. This may help in casing-treatment or tip-treatment to mitigate the loss in the performance, if the tip clearance increases.

Sign in / Sign up

Export Citation Format

Share Document