scholarly journals Analysis of the Temperature Distribution in a Refrigerated Truck Body Depending on the Box Loading Patterns

Foods ◽  
2021 ◽  
Vol 10 (11) ◽  
pp. 2560
Author(s):  
Junhwi So ◽  
Sungyong Joe ◽  
Seonho Hwang ◽  
Soojin Jun ◽  
Seunghyun Lee
Keyword(s):  
Temperature Distribution ◽  
Temperature Sensor ◽  
Turbulence Models ◽  
The Body ◽  
Cold Chain ◽  
Cfd Modeling ◽  
Comsol Multiphysics ◽  
Measured Temperature ◽  
Loading Patterns ◽  
Higher Temperature

The main purpose of cold chain is to keep the temperature of products constant during transportation. The internal temperature of refrigerated truck body is mainly measured with a temperature sensor installed at the hottest point on the body. Hence, the measured temperature cannot represent the overall temperature values of transported products in the body. Moreover, the airflow pattern in the refrigerated body can vary depending on the arrangement of loaded logistics, resulting temperature differences between the transported products. In this study, the airflow and temperature change in the refrigerated body depending on the loading patterns of box were analyzed using experimental and numerical analysis methods. Ten different box loading patterns were applied to the body of 0.5 ton refrigerated truck. The temperatures inside boxes were measured depending on the loading patterns. CFD modeling with two different turbulence models (k-ε and SST k-ω) was developed using COMSOL Multiphysics for predicting the temperatures inside boxes loaded with different patterns, and the predicted data were compared to the experimental data. The k-ε turbulence model showed a higher temperature error than the SST k-ω model; however, the highest temperature point inside the boxes was almost accurately predicted. The developed model derived an approximate temperature distribution in the boxes loaded in the refrigerated body.

scholarly journals Kajian Eksperimental Penggunaan Ruang Pengering Silinder Vertikal dan Horisontal Mesin Pengering Gabah Tipe Fluidzed Deep

2018 ◽  
Vol 2 (1) ◽  
pp. 53
Author(s):  
Mochammad Arvin Syarifuddin ◽  
La Ode M. Firman
Keyword(s):  
Temperature Distribution ◽  
Moisture Content ◽  
Vertical Cylinder ◽  
Vertical Position ◽  
Drying Rate ◽  
Measured Temperature ◽  
Drying Time ◽  
Grain Moisture ◽  
Higher Temperature ◽  
Drying Chamber

Abstract— This study explored experimentally the use of vertical and horisontal position of cylindrical drying chamber dryer Fluidzed Deep against temperature distribution, humidity, drying rate, decreasing grain water level, and decreasing grain mass. The method used in this research is design and experiment. This machine uses a burning furnace as a heat source,sengon/ albasia wood as fuel, flat plate type heat exchanger, cyclone to convert wet vapor to dry vapor, filter to dry vapor cleaner, cylindrical drying chamber, blower to blow air, and Jig to support all components. This experiment was carried out three times for the drying chamber in a vertical position, and three times for the drying chamber in a horisontal position. In one drying time, it takes about 270 minutes. In the drying chamber measured temperature and humidity at 12 points of measurement. The results showed that the horisontal cylinder drying chamber produced higher temperature distribution than the vertical cylinder drying chamber, but the temperature distribution was less even, the vertical cylinder dryer produced lower humidity than the horisontal cylinder drying chamber, but resulted in higher deviation than the horisontal cylinder dryer. Drying rate, decrease in grain water content, average grain decrease on average faster than horisontal cylinder. The process of reducing the grain moisture content from about 20% bb to a moisture content of dry milled grains of about 14% bb occurred for 270 minutes or about 4, 5 hours. Keyword: Experimental design; Fluized deep dryer; dryer efficiency 

Error in Temperature Measurements Due to Conduction Along the Sensor Leads

1976 ◽  
Vol 98 (3) ◽  
pp. 491-495 ◽  
Author(s):  
B. S. Singh ◽  
A. Dybbs
Keyword(s):  
Temperature Distribution ◽  
The Body ◽  
True Temperature ◽  
Measured Temperature ◽  
Internal Temperature ◽  
Sensing Element ◽  
First Approximation ◽  
Immersion Thermocouple ◽  
Thermocouple Wire ◽  
Good Agreement

When a sensor is embedded in a solid body to measure its internal temperature, any conduction to, or from, its sensing element may cause the indicated temperature to be different from the true temperature. This paper describes an analysis of the error caused by conduction when there is an arbitrary temperature distribution in thebbody along the sensor. The sensor is modeled as a cylindrical fin and the appropriate conduction equation is solved. The solution gives a correction for the error which depends on such parameters as, depth of immersion, thermocouple wire and insulation properties, contact between the sensor and the body, and temperature distribution in the body. The latter may not be known, but the measured temperature distribution can be used as a first approximation. The corrected value can then be used to obtain a better estimate of the error. The results show good agreement with experimental observations.

scholarly journals Thermal Characteristics of Breast Surface Temperature in Healthy Women

2021 ◽  
Vol 18 (3) ◽  
pp. 1097
Author(s):  
Anna Lubkowska ◽  
Monika Chudecka
Keyword(s):  
Mammary Gland ◽  
Temperature Distribution ◽  
Surface Temperature ◽  
Thermal Characteristics ◽  
The Body ◽  
Imaging Method ◽  
Infrared Thermal Imaging ◽  
Ir Camera ◽  
Entire Area ◽  
Healthy Women

Thermography is widely used in the medical field, including in the detection of breast disorders. The aim of the research was to characterize the range of breast surface temperature values, taking into account the entire area of the mammary gland and, independently, the nipple, in healthy women. An additional aim was to assess the symmetry of the breast temperature distribution (using an IR camera) and the correlation of temperatures with the content of adipose tissue. Thermograms were made for the right and left breasts, each time delineating the area of the entire breast and a separate area of the nipple, chest, and abdomen. Analyzing the intergroup differences in temperature of selected body areas (Tmean), it was shown that, in all cases, they were significantly higher in younger women. Statistical analysis showed no significant differences between breast and nipple temperatures in relation to the body sides. The highest temperatures within the mammary gland were recorded for the nipple area. The use of the high-resolution digital infrared thermal imaging method in early and screening preventive diagnoses of changes in the mammary gland requires individual interpretation of the results, taking into account the assessment of the physiological pattern of temperature distribution in both breasts.

scholarly journals Simulation of Diffusion Processes in Chemical and Thermal Processing of Machine Parts

Processes ◽  
2021 ◽  
Vol 9 (4) ◽  
pp. 698
Author(s):  
Kateryna Kostyk ◽  
Michal Hatala ◽  
Viktoriia Kostyk ◽  
Vitalii Ivanov ◽  
Ivan Pavlenko ◽  
...  
Keyword(s):  
Mathematical Modeling ◽  
Temperature Distribution ◽  
Thermal Treatment ◽  
Diffusion Processes ◽  
Nitrogen Concentration ◽  
The Body ◽  
Functional Dependencies ◽  
Technological Parameters ◽  
Gas Nitriding ◽  
Temperature State

To solve a number of technological issues, it is advisable to use mathematical modeling, which will allow us to obtain the dependences of the influence of the technological parameters of chemical and thermal treatment processes on forming the depth of the diffusion layers of steels and alloys. The paper presents mathematical modeling of diffusion processes based on the existing chemical and thermal treatment of steel parts. Mathematical modeling is considered on the example of 38Cr2MoAl steel after gas nitriding. The gas nitriding technology was carried out at different temperatures for a duration of 20, 50, and 80 h in the SSHAM-12.12/7 electric furnace. When modeling the diffusion processes of surface hardening of parts in general, providing a specifically given distribution of nitrogen concentration over the diffusion layer’s depth from the product’s surface was solved. The model of the diffusion stage is used under the following assumptions: The diffusion coefficient of the saturating element primarily depends on temperature changes; the metal surface is instantly saturated to equilibrium concentrations with the saturating atmosphere; the surface layer and the entire product are heated unevenly, that is, the product temperature is a function of time and coordinates. Having satisfied the limit, initial, and boundary conditions, the temperature distribution equations over the diffusion layer’s depth were obtained. The final determination of the temperature was solved by an iterative method. Mathematical modeling allowed us to get functional dependencies for calculating the temperature distribution over the depth of the layer and studying the influence of various factors on the body’s temperature state of the body.

scholarly journals Sensors in the Autoclave-Modelling and Implementation of the IoT Steam Sterilization Procedure Counter

Sensors ◽  
2021 ◽  
Vol 21 (2) ◽  
pp. 510
Author(s):  
Lukas Boehler ◽  
Mateusz Daniol ◽  
Ryszard Sroka ◽  
Dominik Osinski ◽  
Anton Keller
Keyword(s):  
The Body ◽  
Surgical Instruments ◽  
Sensor System ◽  
Temperature Profiles ◽  
Measured Temperature ◽  
Steam Sterilization ◽  
Automated Evaluation ◽  
Normative Requirements ◽  
Thermal Simulations ◽  
The Relationship

Surgical procedures involve major risks, as pathogens can enter the body unhindered. To prevent this, most surgical instruments and implants are sterilized. However, ensuring that this process is carried out safely and according to the normative requirements is not a trivial task. This study aims to develop a sensor system that can automatically detect successful steam sterilization on the basis of the measured temperature profiles. This can be achieved only when the relationship between the temperature on the surface of the tool and the temperature at the measurement point inside the tool is known. To find this relationship, the thermodynamic model of the system has been developed. Simulated results of thermal simulations were compared with the acquired temperature profiles to verify the correctness of the model. Simulated temperature profiles are in accordance with the measured temperature profiles, thus the developed model can be used in the process of further development of the system as well as for the development of algorithms for automated evaluation of the sterilization process. Although the developed sensor system proved that the detection of sterilization cycles can be automated, further studies that address the possibility of optimization of the system in terms of geometrical dimensions, used materials, and processing algorithms will be of significant importance for the potential commercialization of the presented solution.

scholarly journals Semidiscrete central difference method in time for determining surface temperatures

2005 ◽  
Vol 2005 (3) ◽  
pp. 393-400 ◽  
Author(s):  
Zhi Qian ◽  
Chu-Li Fu ◽  
Xiang-Tuan Xiong
Keyword(s):  
Difference Method ◽  
Heat Conduction Problem ◽  
A Priori ◽  
Inverse Heat Conduction Problem ◽  
The Body ◽  
Temperature History ◽  
Measured Temperature ◽  
Central Difference ◽  
Approximation Solution ◽  
Computational Effect

We consider an inverse heat conduction problem (IHCP) in a quarter plane. We want to know the distribution of surface temperature in a body from a measured temperature history at a fixed location inside the body. This is a severely ill-posed problem in the sense that the solution (if exists) does not depend continuously on the data. Eldén (1995) has used a difference method for solving this problem, but he did not obtain the convergence atx=0. In this paper, we gave a logarithmic stability of the approximation solution atx=0under a stronger a priori assumption‖u(0,t)‖p≤Ewithp>1/2. A numerical example shows that the computational effect of this method is satisfactory.

Rancang Bangun Pengukur Suhu Tubuh Dengan Multi Sensor Untuk Mencegah Penyebaran Covid-19

2021 ◽  
Vol 5 (3) ◽  
pp. 543-549
Author(s):  
Helmy Yudhistira Putra ◽  
Utomo Budiyanto
Keyword(s):  
Body Temperature ◽  
Temperature Measurement ◽  
Temperature Sensor ◽  
The Body ◽  
Body Temperatures ◽  
Heat Measurement ◽  
Turn On ◽  
Measurement Results ◽  
Door Lock ◽  
Body Heat

During the COVID-19 pandemic, the price of preventive equipment such as masks and hand sanitizers has increased significantly. Likewise, thermometers are experiencing an increase and scarcity, this tool is also sought after by many companies for screening employees and guests before entering the building to detect body temperatures that are suspected of being positive for COVID-19. The use of a thermometer operated by humans is very risky because dealing directly with people who could be ODP (People Under Monitoring/Suscpected ) or even positive for COVID-19, therefore we need tools for automatic body temperature screening and do not involve humans for the examination. This research uses the MLX-90614 body temperature sensor equipped with an ultrasonic support sensor to detect movement and measure the distance between the forehead and the temperature sensor so that the body heat measurement works optimally, and a 16x2 LCD to display the temperature measurement results. If the measured body temperature is more than 37.5 ° C degrees Celsius then the buzzer will turn on and the selenoid door lock will not open and will send a notification to the Telegram messaging application. The final result obtained is the formation of a prototype device for measuring body temperature automatically without the need to involve humans in measuring body temperature to control people who want to enter the building so as to reduce the risk of COVID-19 transmission

CFD Modeling of Transient Flow Phenomena in an Axial Flow VAD

2007 ◽  
Author(s):  
Alexandrina Untaroiu ◽  
Amy L. Throckmorton ◽  
Houston G. Wood ◽  
Paul E. Allaire
Keyword(s):  
Blood Flow ◽  
Transient Flow ◽  
Axial Flow ◽  
The Body ◽  
Cfd Modeling ◽  
Ventricular Assist ◽  
Pump Design ◽  
Design And Optimization ◽  
Wide Range ◽  
Cfd Analyses

A ventricular assist device (VAD) effectively relieves the workload from a native heart, which has been weakened by disease, and increases blood flow supplied to the body to maintain normal physiologic function. The device must be able to operate over a wide range of conditions. Designed to operate at a single, best-efficiency operating point, it must frequently perform at off-design conditions due to a fluctuating flow rate demanded by the human body and a time varying flow within the pump, due to the beating of the native heart. The design and optimization of a blood pump is a challenging and complex process. Pump design equations are used to estimate the initial dimensions of the pump regions. Computational fluid dynamics (CFD) analyses are then performed to optimize the blood flow path according to specific design criteria under steady flow conditions [1].

Temperature Distribution in a Cylindrical Rod Moving From a Chamber at One Temperature to a Chamber at Another Temperature

1964 ◽  
Vol 86 (2) ◽  
pp. 265-270 ◽  
Author(s):  
G. Horvay ◽  
M. Dacosta
Keyword(s):  
Heat Transfer ◽  
Temperature Distribution ◽  
Arbitrary Constant ◽  
Families Of Curves ◽  
Special Cases ◽  
Method Of Solution ◽  
Lower Chamber ◽  
Higher Temperature ◽  
Hopf Method ◽  
The Heat Transfer Coefficient

When an infinitely long cylindrical rod travels from a chamber at one temperature ϑa to a chamber (insulated from the first) at a higher temperature ϑf, then heat will leak out along the rod from the second chamber to the first, whose amount decreases as the speed of the rod increases. Using the Wiener-Hopf method of solution, we determine the temperature distribution in the rod for the case where in the second chamber the heat-transfer coefficient h+ is infinite, while in the first chamber it has an arbitrary constant value h. Families of curves illustrate the temperature distribution in the two special cases where h = ∞ (isothermal boundary conditions in lower chamber) and where h = 0 (rod is insulated in lower chamber).

Sign in / Sign up

Export Citation Format

Share Document