scholarly journals Device Modeling and Design of Inverted Solar Cell Based on Comparative Experimental Analysis between Effect of Organic and Inorganic Hole Transport Layer on Morphology and Photo-Physical Property of Perovskite Thin Film

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2191
Author(s):  
Xiaolan Wang ◽  
Xiaoping Zou ◽  
Jialin Zhu ◽  
Chunqian Zhang ◽  
Jin Cheng ◽  
...  
Keyword(s):  
Light Absorption ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Open Circuit ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer ◽  
Functional Layer ◽  
Perovskite Layer ◽  
The Impact

It is crucial to find a good material as a hole transport layer (HTL) to improve the performance of perovskite solar cells (PSCs), devices with an inverted structure. Polyethylene dioxythiophene-poly (styrene sulfonate) (PEDOT:PSS) and inorganic nickel oxide (NiOx) have become hotspots in the study of hole transport materials in PSCs on account of their excellent properties. In our research, NiOx and PEDOT: PSS, two kinds of hole transport materials, were prepared and compared to study the impact of the bottom layer on the light absorption and morphology of perovskite layer. By the way, some experimental parameters are simulated by wx Analysis of Microelectronic and Photonic Structures (wxAMPS). In addition, thin interfacial layers with deep capture levels and high capture cross sections were inserted to simulate the degradation of the interface between light absorption layer and PEDOT:PSS. This work realizes the combination of experiment and simulation. Exploring the mechanism of the influence of functional layer parameters plays a vital part in the performance of devices by establishing the system design. It can be found that the perovskite film growing on NiOx has a stronger light absorption capacity, which makes the best open-circuit voltage of 0.98 V, short-circuit current density of 24.55 mA/cm2, and power conversion efficiency of 20.01%.

scholarly journals Facile NiOx Sol-Gel Synthesis Depending on Chain Length of Various Solvents without Catalyst for Efficient Hole Charge Transfer in Perovskite Solar Cells

Polymers ◽  
2018 ◽  
Vol 10 (11) ◽  
pp. 1227 ◽  
Author(s):  
Byung Kim ◽  
Woongsik Jang ◽  
Dong Wang
Keyword(s):  
Solar Cells ◽  
Chain Length ◽  
Short Circuit ◽  
Sol Gel ◽  
Perovskite Solar Cells ◽  
Open Circuit ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer ◽  
Perovskite Layer

Nickel oxide (NiOx)–based perovskite solar cells (PSCs) have recently gained considerable interest, and exhibit above 20% photovoltaic efficiency. However, the reported syntheses of NiOx sol-gel used toxic chemicals for the catalysts during synthesis, which resulted in a high-temperature annealing requirement to remove the organic catalysts (ligands). Herein, we report a facile “NiOx sol-gel depending on the chain length of various solvents” method that eschews toxic catalysts, to confirm the effect of different types of organic solvents on NiOx synthesis. The optimized conditions of the method resulted in better morphology and an increase in the crystallinity of the perovskite layer. Furthermore, the use of the optimized organic solvent improved the absorbance of the photoactive layer in the PSC device. To compare the electrical properties, a PSC was prepared with a p-i-n structure, and the optimized divalent alcohol-based NiOx as the hole transport layer. This improved the charge transport compared with that for the typical 1,2-ethanediol (ethylene glycol) used in earlier studies. Finally, the optimized solvent-based NiOx enhanced device performance by increasing the short-circuit current density (Jsc), open-circuit voltage (Voc), and fill factor (FF), compared with those of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate)–based devices.

Optical Simulation and Investigation of the Effect of Hysteresis on the Perovskite Solar Cells

NANO ◽  
2019 ◽  
Vol 14 (10) ◽  
pp. 1950127 ◽  
Author(s):  
Farhad Jahantigh ◽  
S. M. Bagher Ghorashi
Keyword(s):  
Grain Size ◽  
Solar Cells ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer

Perovskite solar cells have recently been considered to be an auspicious candidate for the advancement of future photovoltaic research. A power conversion efficiency (PCE) as high as 22% has been reported to be reached, which can be obtained through an inexpensive and high-throughput solution process. Modeling and simulation of these cells can provide deep insights into their fundamental mechanism of performance. In this paper, two different perovskite solar cells are designed by using COMSOL Multiphysics to optimize the thickness of each layer and the overall thickness of the cell. Electric potential, electron and hole concentrations, generation rate, open-circuit voltage, short-circuit current and the output power were calculated. Finally, PCEs of 20.7% and 26.1% were predicted. Afterwards, according to the simulation results, the role of the hole transport layer (HTL) was investigated and the optimum thickness of the perovskite was measured to be 200[Formula: see text]nm for both cells. Therefore, the spin coating settings are selected so that a coating with this thickness for cell 1 is deposited. In order to compare the performance of HTM layer, solar cells with a Spiro-OMeTAD HTM and without the HTM layer in their structure were fabricated. According to the obtained photovoltaic properties, the solar cell made with Spiro-OMeTAD has a more favorable open-circuit voltage ([Formula: see text]), short-circuit current density ([Formula: see text]), fill factor (FF) and PCE compared to the cell without the HTM layer. Also, hysteresis depends strongly on the perovskite grain size, because large average grain size will lead to an increase in the grain’s contact surface area and a decrease in the density of grain boundaries. Finally, according to the results, it was concluded that, in the presence of a hole transport layer, ion transfer was better and ion accumulation was less intense, and therefore, the hysteresis decreases.

scholarly journals Analysis of the role of hole transport layer materials to the performance of perovskite solar cell

2018 ◽  
Vol 67 ◽  
pp. 01021 ◽  
Author(s):  
Istighfari Dzikri ◽  
Michael Hariadi ◽  
Retno Wigajatri Purnamaningsih ◽  
Nji Raden Poespawati
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Perovskite Solar Cell ◽  
Open Circuit ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer

Research in solar cells is needed to maximize Indonesia’s vast solar potential that can reach up to 207.898 MW with an average radiation of 4.8 kWh/m2/day. Organometallic perovskite solar cells (PSCs) have gained immense attention due to their rapid increase in efficiency and compatibility with low-cost fabrication methods. Understanding the role of hole transport layer is very important to obtain highly efficient PSCs. In this work, we studied the effect of Hole Transport Layer (HTL) to the performance of perovskite solar cell. The devices with HTL exhibit substantial increase in power conversion efficiency, open circuit voltage and short circuit current compared to the device without HTL. The best performing device is PSC with CuSCN as HTL layer, namely Voc of 0.24, Isc of 1.79 mA, 0.27 FF and efficiency of 0.09%.

scholarly journals Thermal oxidation of sputtered nickel nano-film as hole transport layer for high performance perovskite solar cells

2019 ◽  
Vol 30 (22) ◽  
pp. 19792-19803 ◽  
Author(s):  
Mustafa Aboulsaad ◽  
Ayman El Tahan ◽  
Moataz Soliman ◽  
Said El-Sheikh ◽  
Shaker Ebrahim
Keyword(s):  
Nickel Oxide ◽  
Carrier Concentration ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Open Circuit ◽  
Hole Transport ◽  
Transport Layer ◽  
Oxidation Temperature ◽  
Hole Transport Layer ◽  
Performance Measurements

Abstract The effect of rapid oxidation temperature on the sputtered nickel (Ni) films to act as a hole transport layer (HTL) for perovskite solar cell (PSCs) was investigated. A nano-sputtered Ni film with a thickness about 100 nm was oxidized at a range of different oxidation temperatures between 350 and 650 °C to work as HTL in an inverted p–i–n configuration. DC Hall measurement in van der Pauw configuration and photoluminescence spectroscopy were used to measure the charge’s mobility and extraction of nickel oxide (NiO) films. The behaviour of the carrier concentration measurements of NiO layers at different oxidation temperatures showed that the Ni layer oxidized at 450 °C had the highest carrier concentration among the other samples. The performance measurements of the fabricated PSCs showed that the nickel oxide hole-transporting layer which has been oxidized at the optimum oxidation temperature of 450 °C has the highest power conversion efficiency (PCE) of 12.05%. Moreover, the characteristic parameters of the optimum cell such as the open-circuit voltage (VOC), short-circuit current density (JSC) and fill factor (FF) were 0.92 V, 19.80 mA/cm2 and 0.331, respectively.

scholarly journals Investigation of the S-Shaped Current–Voltage Curve in High Open-Circuit Voltage Ruddlesden–Popper Perovskite Solar Cells

2021 ◽  
Vol 9 ◽  
Author(s):  
Hong Zhong ◽  
Renlai Zhou ◽  
Xiaoqing Wu ◽  
Xiaoyun Lin ◽  
Ya Wang ◽  
...  
Keyword(s):  
Solar Cells ◽  
Open Circuit Voltage ◽  
Phase Distribution ◽  
Perovskite Solar Cells ◽  
Open Circuit ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer ◽  
Perovskite Layer ◽  
Current Voltage

We report our investigation on the S-shaped current–voltage characteristics in a hot-casting–processed (BA)2 (MA)3Pb4I13 Ruddlesden–Popper (RP) perovskite solar cell. The two-dimensional perovskite solar cells are fabricated with NiOx as the hole transport layer (HTL), which leads to significantly high open-circuit voltage (Voc). The champion device shows a Voc of 1.21 V and a short current density (Jsc) of 17.14 mA/cm2, leading to an overall power conversion efficiency (PCE) of 13.7%. Although the PCE is much higher than the control device fabricated on PEDOT:PSS, a significant S-shaped current–voltage behavior is observed in these NiOx-based devices. It is found that the S-shaped current–voltage behavior is related to the lower dimensional phase distribution and crystallinity at the bottom interface of the RP perovskite layer, and the S-shaped distortion is less severe after the device ageing test.

scholarly journals Fabrication and Characterization of an Efficient Inverted Perovskite Solar Cells with POSS Passivating Hole Transport Layer

Nanomaterials ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 974
Author(s):  
Bo-Tau Liu ◽  
Hong-Ru Lin ◽  
Rong-Ho Lee ◽  
Nima E. Gorji ◽  
Jung-Chuan Chou
Keyword(s):  
Solar Cells ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Open Circuit ◽  
Hole Transport ◽  
Passivation Layer ◽  
Transport Layer ◽  
Hybrid Nanoparticles ◽  
Hole Transport Layer ◽  
Cage Structure

Polyhedral oligomeric silsesquioxane (POSS), featuring a hollow-cage or semi-cage structure is a new type of organic–inorganic hybrid nanoparticles. POSS combines the advantages of inorganic components and organic components with a great potential for optoelectronic applications such as in emerging perovskite solar cells. When POSS is well dispersed in the polymer matrix, it can effectively improve the thermal, mechanical, magnetic, acoustic, and surface properties of the polymer. In this study, POSS was spin-coated as an ultra-thin passivation layer over the hole transporting layer of nickel-oxide (NOx) in the structure of a perovskite solar cell. The POSS incorporation led to a more hydrophobic and smoother surface for further perovskite deposition, resulting in the increase in the grain size of perovskite. An appropriate POSS passivation layer could effectively reduce the recombination of the electron and hole at grain boundaries and increase the short-circuit current from 18.0 to 20.5 mA·cm−2. Moreover, the open-circuit voltage of the cell could slightly increase over 1 V.

scholarly journals CuI/Spiro-OMeTAD Double-Layer Hole Transport Layer to Improve Photovoltaic Performance of Perovskite Solar Cells

Coatings ◽  
2021 ◽  
Vol 11 (8) ◽  
pp. 978
Author(s):  
Chaoqun Lu ◽  
Weijia Zhang ◽  
Zhaoyi Jiang ◽  
Yulong Zhang ◽  
Cong Ni
Keyword(s):  
Solar Cells ◽  
Double Layer ◽  
Photovoltaic Performance ◽  
Perovskite Solar Cells ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer ◽  
Photoelectric Conversion Efficiency ◽  
Photoelectric Conversion ◽  
Perovskite Layer

The hole transport layer (HTL) is one of the main factors affecting the efficiency and stability of perovskite solar cells (PSCs). However, obtaining HTLs with the desired properties through current preparation techniques remains a challenge. In the present study, we propose a new method which can be used to achieve a double-layer HTL, by inserting a CuI layer between the perovskite layer and Spiro-OMeTAD layer via a solution spin coating process. The CuI layer deposited on the surface of the perovskite film directly covers the rough perovskite surface, covering the surface defects of the perovskite, while a layer of CuI film avoids the defects caused by Spiro-OMetad pinholes. The double-layer HTLs improve roughness and reduce charge recombination of the Spiro-OMeTAD layer, thereby resulting in superior hole extraction capabilities and faster hole mobility. The CuI/Spiro-OMeTAD double-layer HTLs-based devices were prepared in N2 gloveboxes and obtained an optimized PCE (photoelectric conversion efficiency) of 17.44%. Furthermore, their stability was improved due to the barrier effect of the inorganic CuI layer on the entry of air and moisture into the perovskite layer. The results demonstrate that another deposited CuI film is a promising method for realizing high-performance and air-stable PSCs.

scholarly journals The Performance Improvement of Using Hole Transport Layer with Lithium and Cobalt for Inverted Planar Perovskite Solar Cell

Coatings ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 354
Author(s):  
Shaoxi Wang ◽  
He Guan ◽  
Yue Yin ◽  
Chunfu Zhang
Keyword(s):  
Solar Cells ◽  
Short Circuit ◽  
Perovskite Solar Cells ◽  
Hole Mobility ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer ◽  
Planar Heterojunction

With the continuous development of solar cells, the perovskite solar cells (PSCs), whose hole transport layer plays a vital part in collection of photogenerated carriers, have been studied by many researchers. Interface transport layers are important for efficiency and stability enhancement. In this paper, we demonstrated that lithium (Li) and cobalt (Co) codoped in the novel inorganic hole transport layer named NiOx, which were deposited onto ITO substrates via solution methods at room temperature, can greatly enhance performance based on inverted structures of planar heterojunction PSCs. Compared to the pristine NiOx films, doping a certain amount of Li and Co can increase optical transparency, work function, electrical conductivity and hole mobility of NiOx film. Furthermore, experimental results certified that coating CH3NH3PbIxCl3−x perovskite films on Li and Co- NiOx electrode interlayer film can improve chemical stability and absorbing ability of sunlight than the pristine NiOx. Consequently, the power conversion efficiency (PCE) of PSCs has a great improvement from 14.1% to 18.7% when codoped with 10% Li and 5% Co in NiOx. Moreover, the short-circuit current density (Jsc) was increased from 20.09 mA/cm2 to 21.7 mA/cm2 and the fill factor (FF) was enhanced from 0.70 to 0.75 for the PSCs. The experiment results demonstrated that the Li and Co codoped NiOx can be a effective dopant to improve the performance of the PSCs.

scholarly journals Charge extraction via graded doping of hole transport layers gives highly luminescent and stable metal halide perovskite devices

2019 ◽  
Vol 5 (2) ◽  
pp. eaav2012 ◽  
Author(s):  
Mojtaba Abdi-Jalebi ◽  
M. Ibrahim Dar ◽  
Satyaprasad P. Senanayak ◽  
Aditya Sadhanala ◽  
Zahra Andaji-Garmaroudi ◽  
...  
Keyword(s):  
Perovskite Solar Cells ◽  
Hole Transport ◽  
Transport Layer ◽  
Continuous Illumination ◽  
Hole Transport Layer ◽  
Perovskite Layer ◽  
Metal Halide Perovskite ◽  
Hole Transport Layers ◽  
Interfacial Defects ◽  
Extended Power

One source of instability in perovskite solar cells (PSCs) is interfacial defects, particularly those that exist between the perovskite and the hole transport layer (HTL). We demonstrate that thermally evaporated dopant-free tetracene (120 nm) on top of the perovskite layer, capped with a lithium-doped Spiro-OMeTAD layer (200 nm) and top gold electrode, offers an excellent hole-extracting stack with minimal interfacial defect levels. For a perovskite layer interfaced between these graded HTLs and a mesoporous TiO2 electron-extracting layer, its photoluminescence yield reaches 15% compared to 5% for the perovskite layer interfaced between TiO2 and Spiro-OMeTAD alone. For PSCs with graded HTL structure, we demonstrate efficiency of up to 21.6% and an extended power output of over 550 hours of continuous illumination at AM1.5G, retaining more than 90% of the initial performance and thus validating our approach. Our findings represent a breakthrough in the construction of stable PSCs with minimized nonradiative losses.

scholarly journals Efficient Solution Processed CH3NH3PbI3 Perovskite Solar Cells with PolyTPD Hole Transport Layer

2019 ◽  
Vol 74 (8) ◽  
pp. 665-672 ◽  
Author(s):  
Julian Höcker ◽  
David Kiermasch ◽  
Philipp Rieder ◽  
Kristofer Tvingstedt ◽  
Andreas Baumann ◽  
...  
Keyword(s):  
Solar Cells ◽  
Surface Coverage ◽  
Energy Levels ◽  
Perovskite Solar Cells ◽  
Hole Transport ◽  
Transport Layer ◽  
Hole Transport Layer ◽  
Perovskite Layer ◽  
Solvent Engineering ◽  
Highest Occupied Molecular Orbital

AbstractThe organic and hydrophobic polymer poly[N, N′-bis(4-butilphenyl)-N, N′-bis(phenyl)-benzidine] (polyTPD) represents a promising hole transport layer (HTL) for perovskite photovoltaics due to its suitable energy levels, whereby its highest occupied molecular orbital level matches well with the valence band level of methylammonium lead triiodide (CH3NH3PbI3, MAPbI3) perovskite. However, processing a perovskite layer from the solution on the surface of this organic material, is found to be difficult due to the surface properties of the latter. In this study, we evaluate efficient p-i-n type MAPbI3 perovskite solar cells employing differently processed polyTPD layers. We found that the surface coverage of the MAPbI3 perovskite layer strongly depends on the preparation method of the underlying polyTPD layer. By varying the solvents for the polyTPD precursor, its concentration, and by applying an optimised two-step perovskite deposition technique we increased both the surface coverage of the perovskite layer as well as the power conversion efficiency (PCE) of the corresponding solar cell devices. Our simple solvent-engineering approach demonstrates that no further interface modifications are needed for a successful preparation of efficient planar photovoltaic devices with PCEs in the range of 15 %–16 %.

Sign in / Sign up

Export Citation Format

Share Document