scholarly journals Influences of Air-Voids on the Performance of 3D Printing Cementitious Materials

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4438
Author(s):  
Yujun Che ◽  
Shengwen Tang ◽  
Huashan Yang ◽  
Weiwei Li ◽  
Mengyuan Shi
Keyword(s):  
3D Printing ◽  
Mechanical Performance ◽  
Cementitious Materials ◽  
Strength Analysis ◽  
Void Content ◽  
Air Voids ◽  
Void Structure ◽  
3D Printed ◽  
Air Void ◽  
Air Void Content

This paper focuses on inspecting the influences of anti-foaming agent (AFA) on the performance of 3D printing cementitious materials (3DPC). The mini-slump, spreading diameter, yield stress, and strength of 3DPC were evaluated. Additionally, the air-void content, air-void morphology, and air-void size distribution of mortar with and without 0.05% AFA were assessed through image analysis. The mechanical performance and air-void structure of 3D printed samples were also investigated and compared to that of conventionally mould cast samples. Test results show that an optimal AFA content enables 3DPC to achieve favorable workability and mechanical performance. The addition of AFA exhibits lower air-void content in 3DPC than that of the sample without the AFA addition. This reduction in air-void content is further strengthened by the results of strength analysis. Electron microscope analysis shows that the use of AFA results in the suppressed formation of large air-voids during the process of fresh 3DPC. Moreover, the air-void morphology substantially influenced the mechanical performance of hardened 3DPC.

scholarly journals A GPR-Based Pavement Density Profiler: Operating Principles and Applications

2021 ◽  
Vol 13 (13) ◽  
pp. 2613
Author(s):  
Nectaria Diamanti ◽  
A. Peter Annan ◽  
Steven R. Jackson ◽  
Dylan Klazinga
Keyword(s):  
Asphalt Pavement ◽  
Wave Impedance ◽  
Asphalt Mixtures ◽  
Void Content ◽  
Air Voids ◽  
New Instrument ◽  
Pavement Engineering ◽  
And Performance ◽  
Air Void ◽  
Air Void Content

Density is one of the most important parameters in the construction of asphalt mixtures and pavement engineering. When a mixture is properly designed and compacted, it will contain enough air voids to prevent plastic deformation but will have low enough air void content to prevent water ingress and moisture damage. By mapping asphalt pavement density, areas with air void content outside of the acceptable range can be identified to predict its future life and performance. We describe a new instrument, the pavement density profiler (PDP) that has evolved from many years of making measurements of asphalt pavement properties. This instrument measures the electromagnetic (EM) wave impedance to infer the asphalt pavement density (or air void content) locally and over profiles.

Use of Mechanistic Models to Investigate Fatigue Performance of Asphalt Mixtures

2015 ◽  
Vol 2507 (1) ◽  
pp. 108-119 ◽  
Author(s):  
Jong-Sub Lee ◽  
Nelson Gibson ◽  
Y. Richard Kim
Keyword(s):  
Damage Model ◽  
Asphalt Mixtures ◽  
Fatigue Performance ◽  
Void Content ◽  
Continuum Damage ◽  
Direct Tension ◽  
Air Voids ◽  
Viscoelastic Continuum Damage ◽  
Air Void ◽  
Air Void Content

Effects of design air void contents, design voids in mineral aggregate (VMA), and in-place air voids on the fatigue performance of asphalt mixtures were investigated with mechanistic analyses based on the viscoelastic continuum damage (VECD) analyses and the mechanistic–empirical pavement analysis using the AASHTOWare Pavement ME Design program. The VECD analyses included the simplified viscoelastic continuum damage model at the material level and two structural models: ( a) layered viscoelastic analysis and ( b) layered viscoelastic pavement analysis for critical distresses. The mix design of a 2013 accelerated loading facility test lane was selected to develop the volumetric mix designs with the design air voids of 3%, 4%, and 5%, design VMAs of 13%, 14%, and 15%, and in-place air void contents of 5%, 7%, and 9% with the Bailey method. Dynamic modulus and direct tension cyclic fatigue tests were performed in accordance with the AASHTO TP 107 procedure. The test results showed that the linear viscoelastic property was affected by the design VMA, design air void content, and in-place air void content in order of sensitivity. Also, the damage states at failure determined from the damage characteristic curves and the mechanistic fatigue predictions had consistent trends as observed for the design VMA, in-place air void, and design air void content in rank of sensitivity. Finally, the design VMA, in-place air void, and design air void parameters were found to be sensitive in the mechanistic analyses, whereas the parameter that was most sensitive in the pavement mechanistic–empirical analysis was the in-place air void content.

scholarly journals Influences by Air Voids on the Low-Temperature Cracking Property of Dense-Graded Asphalt Concrete Based on Micromechanical Modeling

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Tao Ma ◽  
Yao Zhang ◽  
Hao Wang ◽  
Xiaoming Huang ◽  
Yongli Zhao
Keyword(s):  
Low Temperature ◽  
Asphalt Concrete ◽  
Three Dimensions ◽  
Micromechanical Modeling ◽  
Void Content ◽  
Cracking Behavior ◽  
Air Voids ◽  
Low Temperature Cracking ◽  
Air Void ◽  
Air Void Content

This study characterized the impacts of air voids on the low-temperature cracking behavior of dense-graded asphalt concrete. Virtual low-temperature bending beam test for dense-graded asphalt concrete was built and executed by discrete element method and PFC3D (particle flow code in three dimensions). Virtual tests were applied to analyze the impacts by content, distribution, and size of air voids on the low-temperature properties of dense-graded asphalt concrete. The results revealed that higher air void content results in worse low-temperature property of dense-graded asphalt concrete, especially when the air void content exceeds the designed air content; even with the same designed air void content, different distributing condition of air voids within asphalt concrete leads to different low-temperature properties of asphalt concrete, especially when the air void content in the central-lower part of testing sample varies. Bigger size of single air void which tends to form interconnected air voids within asphalt concrete has more harmful impacts on the low-temperature properties of asphalt concrete. Thus, to achieve satisfied low-temperature properties of dense-graded asphalt concrete, it is critical to ensure the designed air void content, improve the distribution of air voids, and reduce the interconnected air voids for dense-graded asphalt concrete.

scholarly journals Asphalt Layer Density and Air Voids Content: GPR and Laboratory Testing Data Reliance

2020 ◽  
Vol 15 (3) ◽  
pp. 93-110
Author(s):  
Andrius Baltrušaitis ◽  
Audrius Vaitkus ◽  
Juris Smirnovs
Keyword(s):  
Asphalt Pavement ◽  
Relative Dielectric Permittivity ◽  
Void Content ◽  
Air Voids ◽  
The Road ◽  
Layer Density ◽  
Road Pavement ◽  
Ground Penetrating ◽  
Air Void ◽  
Air Void Content

The assurance of asphalt pavement layer compaction, expressed by ratio between field and laboratory bulk density and air voids content, is one of the main criteria of the durability of asphalt road pavement. Destructive measures should be applied and cores should be taken from the asphalt pavement seeking to determine the representative compaction level of the constructed asphalt layers. New methods are constantly being sought for fast, non-destructive and accurate asphalt layer density and air void determination on road. Ground Penetrating Radar (GPR) can allow determining the qualitative characteristics of asphalt pavement across the entire length of the road without causing damage to the road structure. Relative dielectric permittivity, usually called dielectric value or constant, is the leading property used in GPR applications on road pavement surveys. This article presents GPR measurement results from asphalt base and binder layers of four test sections. GPR measurements were conducted immediately after the end of asphalt layer compaction process. Test points on each layer were selected and density, air void content were determined by drilling cores and testing them in the laboratory. To estimate asphalt layer density and air void content, GPR data were analysed using different existing mathematical models. To justify the reliability of the data measured by GPR, results were checked by comparing them with the results measured directly on cores taken from the asphalt pavement layers.

Effects of Water Saturation Level on Resistance of Compacted Hot-Mix Asphalt Samples to Moisture-Induced Damage

2000 ◽  
Vol 1723 (1) ◽  
pp. 97-106 ◽  
Author(s):  
Bouzid Choubane ◽  
Gale C. Page ◽  
James A. Musselman
Keyword(s):  
Water Saturation ◽  
Potential Interaction ◽  
Void Content ◽  
Test Results ◽  
Moisture Susceptibility ◽  
Air Voids ◽  
Florida Department ◽  
Stripping Potential ◽  
Air Void ◽  
Air Void Content

The Florida Department of Transportation (FDOT) initiated monitoring of its first Superpave section on I-75 in Columbia County for stripping potential using AASHTO T 283, which specifies that all conditioned test samples be saturated to between 55 and 80 percent based on 7 ± 1 percent air voids. A fairly large saturation range is allowed because it was thought that mixtures may have different percentages of permeable air voids. However, the potential interaction between air void content and the level of saturation has not been fully investigated. It is also not clear whether test results from samples saturated to 55 percent are comparable with those of the same mixture saturated to 80 percent for a similar air void content. Therefore, although FDOT adopted AASHTO T 283, it also initiated a parallel study on the effects of different degrees of saturation on moisture damage. Findings are reported of both the ongoing monitoring of the I-75 project for potential stripping and the investigation of the effects of different levels of saturation on moisture susceptibility test results as determined using AASHTO T 283.

scholarly journals Moisture Susceptibility of Warm Mix Asphalt (WMA) with an Organic Wax Additive Based on X-Ray Computed Tomography (CT) Technology

2019 ◽  
Vol 2019 ◽  
pp. 1-12 ◽  
Author(s):  
Jie Ji ◽  
Hui Yao ◽  
Zhikai Yuan ◽  
Zhi Suo ◽  
Ying Xu ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Moisture Content ◽  
Void Content ◽  
Moisture Susceptibility ◽  
Air Voids ◽  
X Ray ◽  
X Ray Computed ◽  
Indirect Tensile ◽  
Air Void ◽  
Air Void Content

The warm mix asphalt was fabricated with different moisture contents (0%, 1%, 2%, and 3%) of limestone aggregates using the Superpave gyratory compactor. The moisture susceptibility of asphalt mixtures with an organic wax additive RH was studied. The samples were compacted and tested using the modified Lottman test AASHTO T283, and the X-ray computed tomography technology was used to capture the internal structure images before and after the freeze-thaw cycles. The test results show that the air voids were distributed in the size range of 0–5 mm3 and 5–10 mm3. The number of air voids decreased with the increase of air void size and increased after freeze-thaw cycles. The air void content can be influenced by the residual moisture in aggregates. The higher the moisture content of aggregates is, the larger the air void content is. So, the air void content is likely to be sensitive to moisture damage. The increase ratio of the air void and moisture content of aggregates had good correlation with the indirect tensile strength and tensile strength ratio of the samples. The indirect tensile strength and tensile strength ratio of the samples decreased linearly, and the samples were sensitive to the moisture damage with the increases of increase ratio of the air void/moisture content in aggregates.

scholarly journals Study of High-Temperature Properties of Asphalt Mixtures Used for Bridge Pavement with Concrete Deck

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4238
Author(s):  
Piotr Pokorski ◽  
Piotr Radziszewski ◽  
Michał Sarnowski
Keyword(s):  
Permanent Deformation ◽  
Asphalt Mixture ◽  
Binder Content ◽  
Void Content ◽  
Concrete Bridge ◽  
Asphalt Mixes ◽  
Protective Layers ◽  
Concrete Bridge Decks ◽  
Air Void ◽  
Air Void Content

The paper presents the issue of resistance to permanent deformations of bridge pavements placed upon concrete bridge decks. In Europe, bridge asphalt pavement usually consists of a wearing course and a protective layer, which are placed over the insulation (waterproofing). Protective layers of bridge pavement are commonly constructed using low air void content asphalt mixes as this provides the suitable tightness of such layers. Due to increased binder content, asphalt mixes for bridge pavement may have reduced resistance to permanent deformations. The article presents test results of resistance to permanent deformations of asphalt mixes for the protective layers. In order to determine the composition of mixtures with low air void content and resistance to permanent deformation, an experimental design was applied using a new concept of asphalt mix composition. Twenty-seven different asphalt mixture compositions were analyzed. The mixtures varied in terms of binder content, sand content and grit ratio. Resistance to permanent deformation was tested using the laboratory uniaxial cyclic compression method (dynamic load creep). On the basis of experimental results and statistical analysis, the functions of asphalt mixture permanent deformation resistance were established. This enabled a determination of suitable mixture compositions for protective layers for concrete bridge decks.

Impact of Specimen Configuration and Characteristics on Illinois Flexibility Index

2018 ◽  
Vol 2672 (28) ◽  
pp. 383-393 ◽  
Author(s):  
Jose Rivera-Perez ◽  
Hasan Ozer ◽  
Imad L. Al-Qadi
Keyword(s):  
Correction Factor ◽  
Loading Rate ◽  
Void Content ◽  
Displacement Curve ◽  
Specimen Thickness ◽  
Index Test ◽  
Notch Length ◽  
Air Void ◽  
Flexibility Index ◽  
Air Void Content

The Illinois Department of Transportation adopted the Illinois Flexibility Index Test (I-FIT) to evaluate the cracking vulnerability of asphalt concrete (AC) mixtures that was often shown to increase with the addition of recycled materials such as reclaimed asphalt pavement and recycled asphalt shingles. The test consists of a semi-circular AC sample that has a notch, loaded along the symmetric axis. Fracture energy (FE), post-peak slope, and the flexibility index (FI) are computed from the load displacement curve. These results can be influenced by specimen geometry and test parameters such as loading rate, AC voids content, and so forth. Therefore, this study investigated the effect of notch length, specimen thickness, loading rate, and AC air void content on the I-FIT results. It was found that an increase in the specimen thickness or loading rate resulted in a steeper post-peak slope without affecting the FE. As a result, the FI decreased. An increase in the notch length or AC air void content resulted in a flatter post-peak slope, thus, increasing the FI. From the results, it was concluded that existing correction factors to address the variations caused by specimen thickness and air void content are appropriate. A correction factor to address notch length variations is proposed. A unique correction factor for loading rate could not be developed because of the varying rate dependency of each AC mixture.

Enhanced Model for Continuous Dielectric-Based Asphalt Compaction Evaluation

2018 ◽  
Vol 2672 (26) ◽  
pp. 144-154 ◽  
Author(s):  
Kyle Hoegh ◽  
Shongtao Dai ◽  
Trevor Steiner ◽  
Lev Khazanovich
Keyword(s):  
Dielectric Constants ◽  
Void Content ◽  
Calibration Data ◽  
Stable Model ◽  
Asphalt Overlay ◽  
Longitudinal Joint ◽  
Asphalt Mix ◽  
Pavement Construction ◽  
Air Void ◽  
Air Void Content

The compaction of asphalt concrete significantly affects long-term pavement performance. Although coring provides a relatively accurate way of assessing in-place density at specific locations, the coverage of the assessment is limited, especially at longitudinal joint locations. This can be particularly problematic because it is difficult to identify problematic locations that are likely to fail prematurely using current compaction assessment methods. Ground penetrating radar (GPR) provides an attractive nondestructive testing alternative for evaluation of compaction quality, especially with recent significant improvements in the GPR technology for this specific application. However, assessment of the air void content of the asphalt mix from the GPR-measured dielectric constant of the surface requires conversion of dielectric variation to air void content variation, which is the subject of this paper. An alternative to the commonly used model is proposed, leading to more justifiable predictions for low values of dielectric constants. The proposed model was used to interpret data from a 7-mi long asphalt overlay construction project. The results of the interpretation as compared with the results obtained with the conventional model show an improvement on the stability of the prediction at low air void contents, especially when core calibration data are limited and uncertainty is considered. These results are promising in the direction of reducing field cores necessary to have a stable model providing continuous compaction assessment of new asphalt pavement construction.

Sign in / Sign up

Export Citation Format

Share Document