scholarly journals Experimental Investigation of Moisture Sensitivity and Damage Evolution of Porous Asphalt Mixtures

Materials ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7151
Author(s):  
Xinyu Hu ◽  
Xiaowei Wang ◽  
Nanxiang Zheng ◽  
Qiang Li ◽  
Jinyue Shi
Keyword(s):  
Fatigue Life ◽  
Fatigue Test ◽  
Damage Evolution ◽  
Moisture Damage ◽  
Exponential Model ◽  
Asphalt Mixtures ◽  
Moisture Sensitivity ◽  
Porous Asphalt ◽  
Dry Conditions ◽  
Indirect Tensile

Porous asphalt (PA) mixtures are designed with a high air void (AV) (i.e., 18~22%) content allowing rainwater to infiltrate into their internal structures. Therefore, PA mixtures are more sensitive to moisture damage than traditional densely graded asphalt mixtures. However, the moisture damage evolution of PA mixtures is still unclear. The objective of this study was to investigate the moisture damage evolution and durability damage evolution of PA mixtures. The indirect tensile test (ITT), ITT fatigue test, and Cantabro loss test were used to evaluate the moisture sensitivity and durability of PA mixtures, and a staged ITT fatigue test was developed to investigate the damage evolutions under dry and wet conditions. Indirect tensile strength (ITS), fatigue life, indirect tensile resilience modulus (E), and durability decreased with the increment of moisture damage and loading cycles. The fatigue life is more sensitive to the moisture damage. The largest decrements in ITS and E were found in the first 3000 loading cycles, and PA mixtures tended to fail when the decrement exceeded 60%. Damage factors based on the ITS and E are proposed to predict the loading history of PA mixtures. The durability damage evolution and damage factors could fit an exponential model under dry conditions. Moisture had a significant influence and an acceleration function on the moisture damage evolution and durability damage evolution of PA mixtures.

Moisture Sensitivity of Bituminous Mixtures with Compound Fly Ash Modifier

2012 ◽  
Vol 509 ◽  
pp. 149-154
Author(s):  
Jun Xie ◽  
Jun Cai ◽  
Shao Peng Wu ◽  
Ling Pang
Keyword(s):  
Tensile Strength ◽  
Fatigue Life ◽  
Fly Ash ◽  
Moisture Damage ◽  
Moisture Sensitivity ◽  
Bituminous Mixtures ◽  
Primary Object ◽  
New Type ◽  
Indirect Tensile ◽  
Short Span

Bitumen pavement suffers from moisture damage mainly due to loss of durability and stability in a short span of service life. Filler is known to be capable of increasing the stiffness of bitumen binder, contributing to improvement of moisture sensitivity of bitumen mixture. In this paper a new type of filler named 'Compound Fly Ash Modifier' (CFAM) was introduced in order to enhance the bond strength between acidic aggregate with bitumen. The primary object is to determine the effect of CFAM on the moisture sensitivity of bitumen mixtures prepared by gneiss and granite respectively, which are termed acidic aggregate. Modified Lottman test and fatigue test were conducted. The results show that CFAM improves the resistance of mixes to moisture damage in the increase in indirect tensile strength and the extension of fatigue life. Finally the mechanism of modified effects for CFAM is discussed.

A Comparative Study of Anti-Stripping Additives in Porous Asphalt Mixtures

2014 ◽  
Vol 70 (7) ◽  
Author(s):  
Mohamad Yusri Aman ◽  
Zulkurnain Shahadan ◽  
Mohd Zaime Mat Noh
Keyword(s):  
Asphalt Mixtures ◽  
Cohesive Failure ◽  
Moisture Sensitivity ◽  
Asphalt Mixes ◽  
Air Voids ◽  
Porous Asphalt ◽  
Coefficient Of Permeability ◽  
Indirect Tensile ◽  
Aashto T283 ◽  
Quarry Dust

Presence of water in porous asphalt mixtures detrimentally affected the bonding between binder-aggregate interface and cohesive failure within the binder-filler mastic, making them prone to stripping which contribute to the performance and durability. This paper presents the effect of anti-stripping additives in porous asphalt mixes. In this study, the Marshall specimens were prepared using quarry dust, ordinary Portland Cement (OPC) and Pavement Modifier (PMD) as filler then mixed with 60/70 penetration grade bitumen. The specimens were measured for air voids content and coefficient of permeability and subsequently tested using indirect tensile and Cantabro tests. The moisture sensitivity of porous asphalt was determined based on the ratio of dry and conditioned specimens according to AASHTO T283. The specimens prepared with PMD showed lower air voids content, hence decrease the permeability to give a higher tensile strength and lower abrasion loss compared to specimens prepared with OPC and quarry dust. Based on the results, the PMD filler has a great potential to improve resistance to moisture damage compared to mixes with OPC and specimens prepared with quarry dust fillers.

scholarly journals Examining the Effect of Dry Resin on Moisture Sensitivity of Asphaltic Mixtures

2018 ◽  
Vol 4 (7) ◽  
pp. 1714 ◽  
Author(s):  
Morteza Ghaffari Jajin ◽  
G. Hosein Hamedi
Keyword(s):  
Free Energy ◽  
Surface Free Energy ◽  
Hydrated Lime ◽  
Moisture Damage ◽  
Asphalt Mixtures ◽  
Polymer Additive ◽  
Moisture Sensitivity ◽  
Indirect Tensile ◽  
Effect Of Moisture ◽  
Moisture Resistant

Moisture damage in asphaltic mixtures is defined by the loss of durability and resistance caused by the effect of moisture. The most common way to improve moisture damage in asphaltic mixtures is to use anti-strip additives. This study tended to use dry resin polymer additive to make a moisture-resistant asphaltic mixture. Two types of aggregate indicating different sensitivities against moisture were studied. In order to compare the effect of this material with other anti-strip additives, this study evaluated the effect of hydrated lime on reducing moisture damage and comparing its effect with dry resin polymer additive. The effect of these materials was evaluated by mechanical and thermodynamic concepts using indirect tensile ratio and surface free energy. The results indicated that dry resin polymer used in this study increased alkaline content and reduced acidic content of bituminous surface free energy, resulting in more adhesion between acidic aggregates which are more sensitive to resistance. It also improved bitumen-aggregate adhesion and reduced strip rate. Moreover, hydrated lime as an aggregate anti-strip agent and dry resin polymer as a bituminous modifier significantly increased the resistance of warm asphalt mixtures against moisture. The results of this study show that dry resin polymer can be used as an anti-strip agent instead of hydrated lime with operational problems.

scholarly journals The Effects of Nano Bentonite and Fatty Arbocel on Improving the Behavior of Warm Mixture Asphalt against Moisture Damage and Rutting

2020 ◽  
Vol 6 (5) ◽  
pp. 877-888
Author(s):  
Sepehr Saedi ◽  
Seref Oruc
Keyword(s):  
Moisture Damage ◽  
Asphalt Mixtures ◽  
Maintenance Cost ◽  
Permanent Displacement ◽  
Moisture Sensitivity ◽  
Asphalt Cement ◽  
Dynamic Creep ◽  
Indirect Tensile ◽  
Reduce Energy Consumption ◽  
Low Performance

The use of warm mix asphalt (WMA) technology has increased dramatically in recent years to protect the environment and reduce energy consumption. Despite numerous advantages, WMAs are less commonly used as a result of their lower performance in comparison to HMAs. One of the main reasons for the low performance of WMAs is their high moisture sensitivity. In recent decades, bitumen modifiers have been used to improve the performance of asphalt mixtures. One of the additives that has recently been used to modify the characteristics of bitumen, is bentonite. The grade of asphalt cement used in this study is PG 64 -22 and the Bitumen is modified with 1, 3, 5 and 7% nano bentonite. Also, 0.3% fatty Arbocel has been used for the preparation of WMA. Indirect tensile strength (ITS) test and Nicholson stripping test are used to determine moisture sensitivity and dynamic creep test and LCPC are also used to evaluate the rutting potential. The results indicate that, increasing the percentage of nano bentonite and applying 0.3% of fatty Arbocel improves the resistance of mixture against moisture damage. Also it was found that increasing the mixture hardness decreases the permanent displacement and rutting potential of WMAs. So, it is suggested that the consumption of these additives increases WMA’s lifetime and decreases its maintenance cost.

Research of Mechanical Properties of Asphalt Pavement Materials with WMA and RAP

2012 ◽  
Vol 204-208 ◽  
pp. 3934-3937 ◽  
Author(s):  
Bao Yang Yu ◽  
Yu Wang ◽  
Min Jiang Zhang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Dynamic Modulus ◽  
Asphalt Pavement ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Indirect Tensile Strength ◽  
Porous Asphalt ◽  
Compaction Energy ◽  
Indirect Tensile

The objectives of this paper are to characterize the mechanical properties of porous asphalt pavement mixtures containing RAP and a WMA additive using Super pave gyratory compactor and dynamic modulus testing. Four types of asphalt mixtures were evaluated in this study. This study evaluated compaction energy index, permeability, indirect tensile strength, and dynamic modulus for all types of porous asphalt mixtures. All of the asphalt mixtures meet the typical minimum coefficient of permeability in this study. In addition, only a slight decrease in was found when WMA additive was added to the porous asphalt mixture containing RAP. For indirect tensile strength testing, WMA containing RAP was found to have the highest tensile strength among all of the mixtures tested.

scholarly journals Investigating the Effect of Metal Nanomaterials on the Moisture Sensitivity Process of Asphalt Mixes

2020 ◽  
Author(s):  
Iraj Bargegol ◽  
Farhad Sakanlou ◽  
Mohsen Sohrabi ◽  
Gholam Hossein Hamedi
Keyword(s):  
Free Energy ◽  
Cyclic Loading ◽  
Resilient Modulus ◽  
Moisture Damage ◽  
Mechanical Tests ◽  
Destructive Effect ◽  
Moisture Sensitivity ◽  
Asphalt Mixes ◽  
Indirect Tensile ◽  
Sensitivity Indicator

One of the most common damages in asphalt mixes is the destructive effect of moisture on the binder cohesion and binder–aggregate adhesion which is called moisture damage. There are various methods to improve adhesion and reduce moisture damage in asphalt mixes. The most common of them is using an appropriate additive for binder modification. Accordingly, the current research was conducted to investigate the effect of two nanomaterials (Nano CuO, and Nano SnO2) in 2 different percentages on 2 types of aggregates (granite and limestone) and a type of base binder. In order to investigate the effect of nanomaterials, indirect tensile cyclic loading (the same as resilient modulus test) in dry and wet conditions and surface free energy (SFE) method were used. The moisture sensitivity indicator which shows stripping percentage of aggregate surface in loading cycles using SFE results and indirect tensile cyclic loading, has been considered as the moisture sensitivity indicator in this research. Results of mechanical tests used in this research show that nanomaterials have significantly increased asphalt mixes strength in comparison to control specimens. Results obtained from SFE method show that nanomaterials increase the cohesion free energy; this change causes a reduction in the possibility of failure in binder membrane. Additionally, nanoparticles have increased and reduced basic component and acidic component of SFE, respectively. This leads to improvement of their adhesion with acidic aggregates, which is sensitive to moisture damage.

scholarly journals Evaluation of Fatigue Life of CRM-Reinforced SMA and Its Relationship to Dynamic Stiffness

2014 ◽  
Vol 2014 ◽  
pp. 1-11 ◽  
Author(s):  
Nuha Salim Mashaan ◽  
Mohamed Rehan Karim ◽  
Mahrez Abdel Aziz ◽  
Mohd Rasdan Ibrahim ◽  
Herda Yati Katman ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Fatigue Test ◽  
Resilient Modulus ◽  
Dynamic Stiffness ◽  
Asphalt Mixture ◽  
Fatigue Cracking ◽  
Crumb Rubber ◽  
Fatigue Properties ◽  
Tensile Fatigue ◽  
Indirect Tensile

Fatigue cracking is an essential problem of asphalt concrete that contributes to pavement damage. Although stone matrix asphalt (SMA) has significantly provided resistance to rutting failure, its resistance to fatigue failure is yet to be fully addressed. The aim of this study is to evaluate the effect of crumb rubber modifier (CRM) on stiffness and fatigue properties of SMA mixtures at optimum binder content, using four different modification levels, namely, 6%, 8%, 10%, and 12% CRM by weight of the bitumen. The testing undertaken on the asphalt mix comprises the dynamic stiffness (indirect tensile test), dynamic creep (repeated load creep), and fatigue test (indirect tensile fatigue test) at temperature of 25°C. The indirect tensile fatigue test was conducted at three different stress levels (200, 300, and 400 kPa). Experimental results indicate that CRM-reinforced SMA mixtures exhibit significantly higher fatigue life compared to the mixtures without CRM. Further, higher correlation coefficient was obtained between the fatigue life and resilient modulus as compared to permanent strain; thus resilient modulus might be a more reliable indicator in evaluating the fatigue life of asphalt mixture.

scholarly journals Laboratory Characterization of Porous Asphalt Mixtures with Aramid Fibers

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 1935
Author(s):  
Anik Gupta ◽  
Pedro Lastra-Gonzalez ◽  
Daniel Castro-Fresno ◽  
Jorge Rodriguez-Hernandez
Keyword(s):  
Abrasion Resistance ◽  
Mechanical Performance ◽  
Functional Performance ◽  
Asphalt Mixtures ◽  
Aramid Fiber ◽  
Aramid Fibers ◽  
Porous Asphalt ◽  
Laboratory Characterization ◽  
Dry Conditions ◽  
Analysis Of Results

Recent studies have shown that fibers improve the performance of porous asphalt mixtures. In this study, the influence of four different fibers, (a) regular aramid fiber (RegAR), (b) aramid fiber with latex coating (ARLat), (c) aramid fiber with polyurethane coating (ARPoly), (d) aramid fiber of length 12 mm (AR12) was evaluated on abrasion resistance and toughness of the mixtures. The functional performance was estimated using permeability tests and the mechanical performance was evaluated using the Cantabro test and indirect tensile strength tests. The parameters such as fracture energy, post cracking energy, and toughness were obtained through stress-strain plots. Based on the analysis of results, it was concluded that the addition of ARLat fibers enhanced the abrasion resistance of the mixtures. In terms of ITS, ARPoly and RegAR have positively influenced mixtures under dry conditions. However, the mixtures with all aramid fibers were found to have adverse effects on the ITS under wet conditions and energy parameters of porous asphalt mixtures with the traditional percentages of bitumen in the mixture used in Spain (i.e., approximately 4.5%).

scholarly journals Influence of F-T Synthetic Wax on Asphalt Concrete Permanent Deformation

2013 ◽  
Vol 59 (3) ◽  
pp. 295-312
Author(s):  
M. Iwański ◽  
G. Mazurek
Keyword(s):  
Fatigue Life ◽  
Fatigue Test ◽  
Asphalt Concrete ◽  
Permanent Deformation ◽  
Positive Influence ◽  
Test Results ◽  
Fischer Tropsch ◽  
Stiffness Modulus ◽  
Tensile Fatigue ◽  
Indirect Tensile

Abstract The paper presents the results of the study of the effect of a Fischer-Tropsch (F-T) synthetic wax on the resistance to permanent deformation of the AC 11S asphalt concrete. The synthetic wax was dosed at 1.5%, 2.5% and 3.5% by weight of bitumen 35/50. The compaction temperatures were 115°C, 130°C and 145°C. The criteria adopted for measuring the resistance to permanent deformation included the following parameters: stiffness modulus at 2, 10 and 20°C, permanent deformation (RTS), fatigue life determined using the indirect tensile fatigue test (ITFT) and resistance to rutting (WTSAIR, PRDAIR). The test results confirmed the positive influence of F-T synthetic wax on enhancing the permanent deformation resistance of asphalt concrete placed at lower compaction temperatures compared to that of standard asphalt concrete compacted at 140°C.

Sign in / Sign up

Export Citation Format

Share Document