scholarly journals FEM Analysis of Textile Reinforced Composite Materials Impact Behavior

Materials ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7380
Author(s):  
Savin Dorin Ionesi ◽  
Luminita Ciobanu ◽  
Catalin Dumitras ◽  
Manuela Avadanei ◽  
Ionut Dulgheriu ◽  
...  
Keyword(s):  
Composite Materials ◽  
Impact Resistance ◽  
Fem Analysis ◽  
Impact Behavior ◽  
Time Interval ◽  
Short Time Interval ◽  
Element Analysis ◽  
Textile Reinforced Composite ◽  
And Behavior ◽  
The Impact

Composite materials reinforced with textile fabrics represent a complex subject. When explaining these materials, one must consider their mechanical behavior in general, and impact resistance in particular, as many applications are characterized by dynamic strains. Impact characteristics must be considered from the early stages of the design process in order to be controlled through structure, layer deposition and direction. Reinforcement materials are essential for the quality and behavior of composites, and textile reinforcements present a large range of advantages. It takes a good understanding of the requirements specific to an application to accurately design textile reinforcements. Currently, simulations of textile reinforcements and composites are efficient tools to forecast their behavior during both processing and use. The paper presents the steps that must be followed for modelling the impact behavior of composite materials, using finite element analysis (FEM). The FEM model built using Deform 3D software offers information concerning the behavior structure during impact. The behavior can be visualized for the structure as a whole and, for different sections, be considered significant. Furthermore, the structure’s strain can be visualized at any moment. In real impact tests, this is not possible due to the very short time interval and the impossibility to record inside the structure, as well as to record all significant stages using conventional means.

scholarly journals Evaluation and Validation of a Joint Stress Test to Induce Activity-Related Knee Joint Discomfort — a Prospective Case-Control Study

2021 ◽  
Vol 7 (1) ◽  
Author(s):  
Christiane Schön ◽  
Claudia Reule ◽  
Katharina Knaub ◽  
Antje Micka ◽  
Manfred Wilhelm ◽  
...  
Keyword(s):  
Knee Joint ◽  
Healthy Subjects ◽  
Stress Test ◽  
Osteoarthritis Of The Knee ◽  
Time Interval ◽  
Short Time Interval ◽  
Joint Stress ◽  
Joint Health ◽  
The Impact ◽  
Health Function

Abstract Background The assessment of improvement or maintenance of joint health in healthy subjects is a great challenge. The aim of the study was the evaluation of a joint stress test to assess joint discomfort in subjects with activity-related knee joint discomfort (ArJD). Results Forty-five subjects were recruited to perform the single-leg-step-down (SLSD) test (15 subjects per group). Subjects with ArJD of the knee (age 22–62 years) were compared to healthy subjects (age 24–59 years) with no knee joint discomfort during daily life sporting activity and to subjects with mild-to-moderate osteoarthritis of the knee joint (OA, Kellgren score 2–3, age 42–64 years). The subjects performed the SLSD test with two different protocols: (I) standardization for knee joint discomfort; (II) standardization for load on the knee joint. In addition, range of motion (ROM), reach test, acute pain at rest and after a single-leg squat and knee injury, and osteoarthritis outcome score (KOOS) were assessed. In OA and ArJD subjects, knee joint discomfort could be reproducibly induced in a short time interval of less than 10 min (200 steps). In healthy subjects, no pain was recorded. A clear differentiation between study groups was observed with the SLSD test (maximal step number) as well as KOOS questionnaire, ROM, and reach test. In addition, a moderate to good intra-class correlation was shown for the investigated outcomes. Conclusions These results suggest the SLSD test is a reliable tool for the assessment of knee joint health function in ArJD and OA subjects to study the improvements in their activities. Further, this model can be used as a stress model in intervention studies to study the impact of stress on knee joint health function.

IMPACT RESISTANCE PROPERTIES OF KEVLAR/GLASS FIBER HYBRID COMPOSITE LAMINATES

2015 ◽  
Vol 76 (3) ◽  
Author(s):  
Norazean Shaari ◽  
Aidah Jumahat ◽  
M. Khafiz M. Razif
Keyword(s):  
Glass Fiber ◽  
Hybrid Composite ◽  
Composite Laminates ◽  
Impact Damage ◽  
Impact Resistance ◽  
Impact Behavior ◽  
Slight Reduction ◽  
Depth Of Penetration ◽  
Damage Degree ◽  
The Impact

In this paper, the impact behavior of Kevlar/glass fiber hybrid composite laminates was investigated by performing the drop weight impact test (ASTM D7136). Composite laminates were fabricated using vacuum bagging process with an epoxy matrix reinforced with twill Kevlar woven fiber and plain glass woven fiber. Four different types of composite laminates with different ratios of Kevlar to glass fiber (0:100, 20:80, 50:50 and 100:0) were manufactured. The effect of Kevlar/glass fiber content on the impact damage behavior was studied at 43J nominal impact energy. Results indicated that hybridization of Kevlar fiber to glass fiber improved the load carrying capability, energy absorbed and damage degree of composite laminates with a slight reduction in deflection. These results were further supported through the damage pattern analysis, depth of penetration and X-ray evaluation tests. Based on literature work, studies that have been done to investigate the impact behaviour of woven Kevlar/glass fiber hybrid composite laminates are very limited. Therefore, this research concentrates on the effect of Kevlar on the impact resistance properties of woven glass fibre reinforced polymer composites.

scholarly journals Numerical modeling of the impact behavior of new particulate-loaded composite materials

2003 ◽  
Vol 61 (1-2) ◽  
pp. 151-159 ◽  
Author(s):  
A. Arias ◽  
R. Zaera ◽  
J. López-Puente ◽  
C. Navarro
Keyword(s):  
Numerical Modeling ◽  
Composite Materials ◽  
Impact Behavior ◽  
The Impact

scholarly journals Study on the Impact Resistance of Metal Flexible Net to Rock fall

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Gaosheng Wang ◽  
Yunhou Sun ◽  
Ao Zhang ◽  
Lei Zheng ◽  
Yuzheng Lv ◽  
...  
Keyword(s):  
Finite Element ◽  
Impact Force ◽  
Impact Resistance ◽  
Time History ◽  
Rock Fall ◽  
Fe Model ◽  
Element Analysis ◽  
Inclination Angles ◽  
Fall Protection ◽  
The Impact

Based on experiments and finite element analysis, the impact resistance of metal flexible net was studied, which can provide reference for the application of metal flexible net in rock fall protection. The oblique (30 degrees) impact experiment of metal flexible net was carried out, the corresponding finite element (FE) to the experiment was established, and the FE model was verified by simulation results to the experimental tests from three aspects: the deformation characteristics of metal flexible net, the time history curves of impact force on supporting ropes, and the maximum instantaneous impact force on supporting ropes. The FE models of metal flexible nets with inclination angles of 0, 15, 30, 45, 60, and 75 degrees were established, and the impact resistance of metal flexible nets with different inclination angles was analyzed. The research shows that the metal flexible net with proper inclination can bounce the impact rock fall out of the safe area and prevent rock fall falling on the metal flexible net, thus realizing the self-cleaning function. When the inclination angle of the metal flexible net is 15, 30, and 45 degrees, respectively, the bounce effect after impact is better, the remaining height is improved, the protection width is improved obviously, and the impact force is reduced. Herein, the impact force of rock fall decreases most obviously at 45 degrees inclination, and the protective performance is relatively good.

Experimental and Numerical Study of Basalt FRP Strip Strengthened RC Slabs under Impact Loads

2020 ◽  
Vol 20 (06) ◽  
pp. 2040001 ◽  
Author(s):  
Wensu Chen ◽  
Thong M. Pham ◽  
Mohamed Elchalakani ◽  
Huawei Li ◽  
Hong Hao ◽  
...  
Keyword(s):  
Failure Modes ◽  
Shear Failure ◽  
Numerical Study ◽  
Impact Resistance ◽  
Basalt Fiber ◽  
Impact Behavior ◽  
Impact Loads ◽  
Quantitative Measurements ◽  
Rc Slabs ◽  
The Impact

Basalt fiber-reinforced polymer (BFRP) has been applied for strengthening concrete structures. However, studies on reinforced concrete (RC) slabs strengthened by BFRP strips under impact loads are limited in open literature. This study investigates the efficiency of using BFRP strips with various strengthening layouts and anchoring schemes on the impact resistance of RC slabs. A total of 11 two-way square slabs were prepared and tested, including one reference specimen without strengthening and ten slabs strengthened with BFRP strips and/or anchors. The RC slabs were impacted by a drop weight with increasing height until slab failure. The observed failure modes include punching shear failure, BFRP sheet debonding and reinforcement fracture. The failure modes and the effects of using various strengthening schemes on the impact resistant capacity of RC slabs were examined. The quantitative measurements, such as impact velocity, indentation depth and diameter, were compared and discussed. In addition, numerical studies were carried out by using LS-DYNA to simulate the impact tests of RC slabs with and without BFRP strengthening. With the calibrated numerical model, the impact behavior of slabs with various dimensions and strengthening layouts under different impact intensities can be predicted with good accuracy.

scholarly journals Effect of Mold Temperature on the Impact Behavior and Morphology of Injection Molded Foams Based on Polypropylene Polyethylene–Octene Copolymer Blends

Polymers ◽  
2019 ◽  
Vol 11 (5) ◽  
pp. 894 ◽  
Author(s):  
Santiago Muñoz-Pascual ◽  
Eduardo Lopez-Gonzalez ◽  
Cristina Saiz-Arroyo ◽  
Miguel Angel Rodriguez-Perez
Keyword(s):  
Impact Resistance ◽  
Mold Temperature ◽  
Impact Behavior ◽  
Critical Parameters ◽  
Crystalline Morphology ◽  
Copolymer Blends ◽  
Opposite Trend ◽  
Izod Impact ◽  
Injection Molded ◽  
The Impact

In this work, an isotactic polypropylene (PP) and a polyethylene–octene copolymer (POE) have been blended and injection-molded, obtaining solids and foamed samples with a relative density of 0.76. Different mold temperature and injection temperature were used. The Izod impact strength was measured. For solids, higher mold temperature increased the impact resistance, whereas in foams, the opposite trend was observed. In order to understand the reasons of this behavior, the morphology of the elastomeric phase, the crystalline morphology and the cellular structure have been studied. The presence of the elastomer near the skin in the case of high mold temperature can explain the improvement produced with a high mold temperature in solids. For foams, aspects as the elastomer coarsening in the core of the sample or the presence of a thicker solid skin are the critical parameters that justify the improved behavior of the materials produced with a lower mold temperature.

The Research of the Shock Angular Displacement Sensor

2013 ◽  
Vol 427-429 ◽  
pp. 1060-1063
Author(s):  
Rong Xian Liu ◽  
Yong Fa Qin ◽  
Fan Li
Keyword(s):  
Angular Displacement ◽  
Impact Resistance ◽  
High Strength ◽  
Measurement Range ◽  
Displacement Sensor ◽  
Gravitational Acceleration ◽  
Element Analysis ◽  
Displacement Sensors ◽  
Large Measurement ◽  
The Impact

Impact resistance angular displacement sensors are widely used in motion mechanical system, which not only requires the sensor having the advantages of large measurement range, long life, also the sensor need to withstand shock and vibration. We use the finite element analysis on the key structure of the sensor and design the sensor circuit.. The sensor has the advantages of high strength shell and flexible packaging, and it can withstand the impact of the gravitational acceleration 100g on three directions.

Impact Experiment and Analysis of the Carbon Fiber Composite Plate with the Central Hole

2013 ◽  
Vol 821-822 ◽  
pp. 158-161
Author(s):  
Kuo Yi Huang ◽  
Gwo Chung Tsai
Keyword(s):  
Composite Plate ◽  
Fiber Composite ◽  
Impact Resistance ◽  
Central Hole ◽  
Carbon Fiber Composite ◽  
Element Analysis ◽  
Absorption Energy ◽  
The Finite Element Analysis ◽  
Teflon Sheet ◽  
The Impact

The composite material plate with the central hole is made by the composite prepreg. During the laying, the circle Teflon sheet is installed into the center of the composite plate. After curing, the center circle area was cut-out and the composite plate with the central hole was observed. Three different central holes are designed by the diameter of 12 mm, 14 mm, and 16 mm. The composite plate with central hole is stroke by the impact-or to measure the absorption energy, and acceleration to compare their impact resistance. The finite element analysis is also used to analyze the mechanical behavior of the plate during and after the impact. The results showed that the energy absorption capability is lower when the central hole became bigger.

Sign in / Sign up

Export Citation Format

Share Document