scholarly journals A Ru/RuO2-Doped TiO2 Nanotubes as pH Sensors for Biomedical Applications: The Effect of the Amount and Oxidation of Deposited Ru on the Electrochemical Response

Materials ◽  
2021 ◽  
Vol 14 (24) ◽  
pp. 7912
Author(s):  
Nikola Macháčková ◽  
Jitřenka Jírů ◽  
Vojtěch Hybášek ◽  
Jaroslav Fojt
Keyword(s):  
Electrochemical Impedance ◽  
Ph Sensor ◽  
Base Material ◽  
Open Circuit ◽  
Impedance Method ◽  
Ph Change ◽  
Corrosion Properties ◽  
Cyclic Polarization ◽  
Potentiostatic Mode ◽  
Electrochemical Response

In the field of orthopedic or dental implants, titanium and its alloys are most commonly used because of their excellent mechanical and corrosion properties and good biocompatibility. After implantation into the patient’s body, there is a high risk of developing bacterial inflammation, which negatively affects the surrounding tissues and the implant itself. Early detection of inflammation could be done with a pH sensor. In this work, pH-sensitive systems based on TiO2-Ru and TiO2-RuO2 combinations were fabricated and investigated. As a base material, Ti-6Al-4V alloy nanostructured by anodic oxidation was used. Ruthenium was successfully deposited on nanotubular TiO2 using cyclic polarization, galvanostatic and potentiostatic mode. Potentiostatic mode proved to be the most suitable. The selected samples were oxidized by cyclic polarization to form a TiO2-RuO2 system. The success of the oxidation was confirmed by XPS analysis. The electrochemical response of the systems to pH change was measured in saline solution using different techniques. The measurement of open circuit potential showed that unoxidized samples (TiO2-Ru) exhibited sub-Nernstian behavior (39.2 and 35.8 mV/pH). The oxidized sample (TiO2-RuO2) containing the highest amount of Ru exhibited super-Nernstian behavior (67.3 mV/pH). The Mott–Schottky analysis proved to be the best method. The use of the electrochemical impedance method can also be considered, provided that greater stability of the samples is achieved.

scholarly journals Sacrificial Dissolution of Zinc Electroplated and Cold Galvanized Coated Steel in Saline and Soil Environments: A Comparison

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 744
Author(s):  
Ameeq Farooq ◽  
Umer Masood Chaudry ◽  
Ahsan Saleem ◽  
Kashif Mairaj Deen ◽  
Kotiba Hamad ◽  
...  
Keyword(s):  
Corrosion Rate ◽  
Electrochemical Impedance ◽  
Saline Soil ◽  
Steel Substrate ◽  
Salt Spray ◽  
Steel Structures ◽  
Open Circuit ◽  
Cyclic Polarization ◽  
Transfer Resistance ◽  
Soil Solutions

To protect steel structures, zinc coatings are mostly used as a sacrificial barrier. This research aims to estimate the dissolution tendency of the electroplated and zinc-rich cold galvanized (ZRCG) coatings of a controlled thickness (35 ± 1 μm) applied via brush and dip coating methods on the mild steel. To assess the corrosion behavior of these coated samples in 3.5% NaCl and 10% NaCl containing soil solutions, open circuit potential (OCP), cyclic polarization (CP), and electrochemical impedance spectroscopy (EIS) tests were performed. The more negative OCP and appreciably large corrosion rate of the electroplated and ZRCG coated samples in 3.5% NaCl solution highlighted the preferential dissolution of Zn coatings. However, in saline soil solution, the relatively positive OCP (>−850 mV vs. Cu/CuSO4) and lower corrosion rate of the electroplated and ZRCG coatings compared to the uncoated steel sample indicated their incapacity to protect the steel substrate. The CP scans of the zinc electroplated samples showed a positive hysteresis loop after 24 h of exposure in 3.5% NaCl and saline soil solutions attributing to the localized dissolution of the coating. Similarly, the appreciable decrease in the charge transfer resistance of the electroplated samples after 24 h of exposure corresponded to their accelerated dissolution. Compared to the localized dissolution of the electroplated and brush-coated samples, the dip-coated ZRCG samples exhibited uniform dissolution during the extended exposure (500 h) salt spray test.

Application of Electrochemical Techniques to Characterization of the Corrosion Behaviors of GW63 Alloys

2007 ◽  
Vol 546-549 ◽  
pp. 571-574
Author(s):  
Xing Wu Guo ◽  
Jian Wei Chang ◽  
Shang Ming He ◽  
Peng Huai Fu ◽  
Wen Jiang Ding
Keyword(s):  
Electrochemical Impedance ◽  
Electrochemical Techniques ◽  
Open Circuit ◽  
Cyclic Polarization ◽  
Time Curve ◽  
Completely Monotonic ◽  
Treatment Conditions ◽  
Impedance Variation ◽  
Corrosion Behaviors

The corrosion behavior of GW63 (Mg-6wt.%Gd-3wt.%Y-0.4wt.%Zr) alloys in 5% NaCl aqueous solution has been investigated by PARSTAT 2273 instrument. The Open Circuit Potential (ECORR) vs. time curve, cyclic polarization (Pitting Scans) curve and Electrochemical Impedance Spectroscopy (EIS) was measured for the GW63 alloys in as-cast and T6 heat treatment conditions. The EIS results indicated that the tendency of impedance variation for as-cast condition was monotonic decreasing, however, the tendency of variation for T6 condition was not completely monotonic but the total tendency was decreasing. The values of impedance of GW63 alloy at 0.1 Hz are about 103 ohm-cm2 for as-cast and T6 condition.

Corrosion Behavior of Ti-7 Wt.% Mn Alloy in Artificial Saliva

2020 ◽  
Vol 835 ◽  
pp. 288-296 ◽  
Author(s):  
Adel Attia ◽  
Lobna A. Khorshed ◽  
Lamiaa Z. Mohamed ◽  
Mohammed A. Gepreel
Keyword(s):  
Electrochemical Impedance ◽  
Artificial Saliva ◽  
Annealed Sample ◽  
Open Circuit ◽  
Corrosion Properties ◽  
X Ray ◽  
Specific Strength ◽  
Corrosion Resistance Property ◽  
Cold Rolled ◽  
Dental Applications

Ti-Mn alloy has a high specific strength, excellent cold workability and good biocompatibility. A cold rolled Ti-7 wt.% Mn was compared to annealed sample at 900°C for 10 min and the corrosion resistance property was tested in artificial saliva solution (AS). The Ti-7 wt.% Mn alloys (cold rolled and annealed) were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Energy dispersive X-ray analysis (EDX) and compared to pure Ti. Simultaneously, the alloys tested in the AS solution for up to 28 days mainly by following the open-circuit potential (OCP), electrochemical impedance spectroscopy (EIS), SEM and EDX. Annealed Ti-7wt.% Mn showed good corrosion properties similar to that of pure Ti, hence the new Ti-7wt.%Mn alloy have higher specific strength than pure Ti, yet showed same corrosion properties which favor implanted dental applications.

Evaluation of Ni0.5Zn0.5Fe2O4 nanoparticles as anti-corrosion pigment in organic coatings for carbon steel

2017 ◽  
Vol 64 (6) ◽  
pp. 644-653 ◽  
Author(s):  
A.U. Chaudhry ◽  
Vikas Mittal ◽  
M.I. Hashmi ◽  
Brajendra Mishra
Keyword(s):  
Carbon Steel ◽  
Electrochemical Impedance ◽  
Electrochemical Techniques ◽  
Open Circuit ◽  
Corrosion Layer ◽  
Organic Coatings ◽  
Metallic Oxide ◽  
Corrosion Properties ◽  
Content Type ◽  
Wide Range

Purpose Inorganic oxide addition can be synergistically beneficial in organic coatings if it can impart anti-corrosion properties and also act as an additive to enhance physical and/or chemical properties. The aim of this study was to evaluate the anti-corrosion benefits of nano nickel zinc ferrite (NZF) in the polymer film. Design/methodology/approach The time-dependent anti-corrosion ability of NZF (0.12-1.0 per cent w/w NZF/binder), applied on API 5L X-80 carbon steel, was characterized by electrochemical techniques such as open circuit potential, electrochemical impedance spectroscopy, linear polarization resistance and potentiodynamic. Characterization of corrosion layer was done by removing coatings after 216 h of immersion in 3.5 per cent w/v NaCl. Optical microscopy, field emission scanning electron microscopy and X-ray diffraction techniques were used to characterize the corroded surface. Findings Corrosion measurements confirm the electrochemical activity by metallic cations on the steel surface during corrosion process which results in improvement of anti-corrosion properties of steel. Moreover, surface techniques show compact corrosion layer coatings and presence of different metallic oxide phases for nanocomposite coatings. Originality/value The suggested protection mechanism was explained by the leaching and precipitation of metallic ion on the corroded surface which in turn slowed down the corrosion activity. Furthermore, improvement in barrier properties of rubber-based coatings was confirmed by the enhanced pore resistance. This work indicates that along with a wide range of applications of NZF, anti-corrosion properties can be taken as an addition.

scholarly journals Effect of Iron Content on Corrosion Properties of Pure Titanium as Grain Refiner

Materials ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7193
Author(s):  
Bosung Seo ◽  
Hyeon-Tae Im ◽  
Ki-Beom Park ◽  
Kwangsuk Park ◽  
Hyung-Ki Park
Keyword(s):  
Corrosion Resistance ◽  
Open Circuit Potential ◽  
Electrochemical Impedance ◽  
Pure Titanium ◽  
Open Circuit ◽  
Tio2 Layer ◽  
Grain Refiner ◽  
Corrosion Properties ◽  
Acid Environment ◽  
Titanium Cathode

Microstructures and corrosion properties of pure titanium were characterized when iron was used as a grain refiner. The added Fe element acted as a strong grain refiner for pure titanium by forming β Ti phase at grain boundaries, and 0.15 wt% Fe was revealed to be a sufficient amount to make the grain size of pure titanium below 20 μm, which was the requirement for the desired titanium cathode. However, corrosion resistance was decreased with the Fe amount added. From the open circuit potential (OCP) results, it was obvious that the TiO2 stability against the reducing acid environment was deteriorated with the Fe amount, which seemed to be the main reason for the decreased corrosion resistance. Electrochemical impedance spectroscopy (EIS) results showed that both the decrease in the compact oxide film’s resistance (Rb) and the appearance of the outer porous film occurred as a result of the dissolution of the TiO2 layer, whose phenomena became more apparent as more Fe was added.

Effects of pH and Elevated Glucose Levels on the Electrochemical Behavior of Dental Implants

2014 ◽  
Vol 40 (2) ◽  
pp. 153-159 ◽  
Author(s):  
Evsen Tamam ◽  
Ilser Turkyilmaz
Keyword(s):  
Dental Implants ◽  
Electrochemical Impedance ◽  
Electrochemical Corrosion ◽  
Physiological Solution ◽  
Titanium Implants ◽  
Corrosion Properties ◽  
Cyclic Polarization ◽  
High Blood Glucose ◽  
Glucose Levels ◽  
Corrosion Rates

Implant failure is more likely to occur in persons with medically compromising systemic conditions, such as diabetes related to high blood glucose levels and inflammatory diseases related to pH levels lower than those in healthy people. The aim of this study was to investigate the effects of lower pH level and simulated- hyperglycemia on implant corrosion as these effects are critical to biocompatibility and osseointegration. The electrochemical corrosion properties of titanium implants were studied in four different solutions: Ringer's physiological solution at pH = 7.0 and pH = 5.5 and Ringer's physiological solution containing 15 mM dextrose at pH = 7 and pH = 5.5. Corrosion behaviors of dental implants were determined by cyclic polarization test and electrochemical impedance spectroscopy. Surface alterations were studied using a scanning electron microscope. All test electrolytes led to apparent differences in corrosion behavior of the implants. The implants under conditions of test exhibited statistically significant increases in Icorr from 0.2372 to 1.007 μAcm−2, corrosion rates from 1.904 to 8.085 mpy, and a decrease in polarization resistances from 304 to 74 Ω. Implants in dextrose-containing solutions were more prone to corrosion than those in Ringer's solutions alone. Increasing the acidity also yielded greater corrosion rates for the dextrose-containing solutions and the solutions without dextrose.

scholarly journals The Corrosion Properties of S355J2 Steel Welded Joint in Chlorides Environment

2018 ◽  
Vol 47 (4) ◽  
pp. 342-347
Author(s):  
Kamil Borko ◽  
Branislav Hadzima ◽  
Filip Pastorek
Keyword(s):  
Corrosion Resistance ◽  
Weld Metal ◽  
Welded Joint ◽  
Electrochemical Impedance ◽  
Base Material ◽  
Electrochemical Characteristics ◽  
Corrosion Properties ◽  
Electrochemical Tests ◽  
Different Types ◽  
Submerged Arc

Nowadays are steels the most used structural material for creation of constructions in different types of industry for lot of applications but suffer from unsatisfactory corrosion resistance in the presence of aggressive chlorides. Steel S355J2 represents common type steel for constructions. Very important property of S355J2 steel is weldability. S355J2 steel was welded by submerged arc welding (SAW) method. Corrosion resistance of welded joint was evaluated by electrochemical methods - linear polarization (LP) and electrochemical impedance spectroscopy (EIS). Results from electrochemical tests are general electrochemical characteristics - ECorr, iCorr, vCorr and RP. Environments for testing were solutions with different concentration of chlorides (0.01M, 0.1M and 1M NaCl solution). Difference of corrosion resistance between base material and weld metal is app. 14.5 %. This difference is preserved in all concentrations of tested environments. The highest corrosion resistance was reached by base material in 0.01M NaCl and the lowest corrosion resistance was reached by weld metal in 1M NaCl.

scholarly journals Influence of Abrasive Load on Wettability and Corrosion Inhibition of a Commercial Superhydrophobic Coating

Coatings ◽  
2020 ◽  
Vol 10 (9) ◽  
pp. 887
Author(s):  
Arjun Manoj ◽  
Rahul Ramachandran ◽  
Pradeep L. Menezes
Keyword(s):  
Contact Angle ◽  
Corrosion Inhibition ◽  
Mechanical Stability ◽  
Electrochemical Impedance ◽  
Contact Angle Hysteresis ◽  
Open Circuit ◽  
Superhydrophobic Coating ◽  
Corrosion Properties ◽  
Wetting Properties ◽  
Before And After

The poor mechanical stability of hydrophobic and superhydrophobic surfaces and coatings severely hinder their commercial and industrial applicability. In addition to being expensive and time-consuming to manufacture, the ability of these coatings to maintain their non-wetting properties after mechanical abrasion and wear is currently not well-understood. In this work, the influence of increasing abrasive loads on the roughness, wettability, and corrosion inhibition properties of a commercial superhydrophobic coating was studied. It was shown that the wetting and corrosion properties of the superhydrophobic coating was affected by the abrasive load. Increasing abrasive loads were applied using a tribometer and the electrochemical response was studied using open circuit potential, potentiodynamic polarization, and electrochemical impedance spectroscopy. The wetting and roughness behavior of the coating before and after the application of the abrasive load was characterized using contact angle, contact angle hysteresis, and optical profilometry. The protective properties of the superhydrophobic coating was observed to deteriorate as the abrasive load increased. Similarly, after a specific abrasive load, the coating transitioned from the Cassie-Baxter state of wetting into that of the Wenzel state.

scholarly journals Synthesis and Characterization of Polyaniline-Based Polymer Nanocomposites as Anti-Corrosion Coatings

Coatings ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 653
Author(s):  
Francisco R. Rangel-Olivares ◽  
Elsa M. Arce-Estrada ◽  
Román Cabrera-Sierra
Keyword(s):  
Polymer Nanocomposites ◽  
Electrochemical Impedance ◽  
Oxidative Polymerization ◽  
Open Circuit ◽  
Degree Of Crystallinity ◽  
X Ray Diffraction ◽  
Corrosion Properties ◽  
X Ray ◽  
Hydrochloric Acid Medium ◽  
Ft Ir

Polymer nanocomposites of polyaniline (PANI)-based metal oxides (SiO2, CeO2, and TiO2A) were synthesized by in situ chemical oxidative polymerization by rapid mixing in a hydrochloric acid medium to evaluate and compare their performance as anti-corrosion coatings on commercial 1018 steel in a 3.5% NaCl medium. The anti-corrosion coatings were developed by dispersing synthesized nanocomposites on an alkydalic resin (AR) for their subsequent electrochemical characterization. X-ray diffraction (XRD) analyses show that PANI has a certain degree of crystallinity in its structure. The incorporation of metal oxide (MO) nanoparticles (NPs) into the polymer matrix was confirmed by scanning electron microscopy and energy-dispersive X-ray spectroscopy (SEM-EDS) analyses, while the interaction of nanoparticles with PANI was proven by Fourier transform infrared (FT-IR) and ultraviolet-visible (UV-vis). Thermogravimetric analysis (TGA) reveals that nanoparticles infer greater resistance to the thermal decomposition of PANI. Finally, the use of open circuit potential (OCP) study, Tafel curves, and electrochemical impedance spectroscopy (EIS) showed that coatings made with TiO2A NPs exhibit the best anti-corrosion properties as compared to those synthesized with SiO2 and CeO2 NPs.

scholarly journals Galvanic Corrosion Study between Tensile-Stressed and Non-Stressed Carbon Steels in Simulated Concrete Pore Solution

Metals ◽  
2022 ◽  
Vol 12 (1) ◽  
pp. 98
Author(s):  
Zheng Dong ◽  
Chuanqing Fu ◽  
Amir Poursaee
Keyword(s):  
Charge Transfer ◽  
Tensile Stress ◽  
Electrochemical Impedance ◽  
Pore Solution ◽  
Charge Transfer Resistance ◽  
Open Circuit ◽  
Carbon Steels ◽  
Cyclic Polarization ◽  
Transfer Resistance ◽  
Low Frequencies

The present study investigated the galvanic effect between tensile-stressed and non-stressed carbon steels, in addition to the influence of the tensile stress on the passivation and corrosion behavior of steel in a simulated concrete pore solution. Three different levels of tensile stress, ranging from elastic to plastic stress on the surface, were applied by adjusting the displacement of C-shape carbon steel rings. Different electrochemical measurements including the open circuit potential (OCP), the electrochemical impedance spectroscopy (EIS), the zero-resistance ammetry (ZRA), and the cyclic polarization were performed. Based on the results of EIS, the tensile stress degraded the resistance of the oxide film in moderate frequencies while enhancing the charge transfer resistance in low frequencies during passivation. As corrosion propagated, the stressed steel yielded a similar charge transfer resistance to or an even lower charge transfer resistance than the non-stressed steel, especially in the case of plastic tensile stress. The galvanic effect between the tensile-stressed and non-stressed steels increased the chloride threshold value of the tensile-stressed steel, although the susceptibility to pitting corrosion was exhibited after being corroded.

Sign in / Sign up

Export Citation Format

Share Document