scholarly journals Strength Tests and Numerical Simulations of Loess Modified by Desulfurization Ash and Fly Ash

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 512
Author(s):  
Zhi Cheng ◽  
Xinrong Cheng ◽  
Yuchao Xie ◽  
Zhe Ma ◽  
Yuhao Liu
Keyword(s):  
Shear Strength ◽  
Fly Ash ◽  
Power Plants ◽  
Utilization Rate ◽  
Direct Shear ◽  
Test Results ◽  
Mass Ratio ◽  
Direct Shear Tests ◽  
Strength Tests ◽  
Actual Test

Desulfurization ash and fly ash are solid wastes discharged from boilers of power plants. Their utilization rate is low, especially desulfurization ash, most of which is stored. In order to realize their resource utilization, they are used to modify loess in this paper. Nine group compaction tests and 32 group direct shear tests are done in order to explore the influence law of desulfurization ash and fly ash on the strength of the loess. Meanwhile, FLAC3D software is used to numerically simulate the direct shear test, and the simulation results and the test results are compared and analyzed. The results show that, with the increase of desulfurization ash’s amount, the shear strength of the modified loess increases first and then decreases. The loess modified by the fly ash has the same law with that of the desulfurization ash. The best mass ratio of modified loess is 80:20. When the mass ratio is 80:20, the shear strength of loess modified by the desulfurization ash is 12.74% higher than that of the pure loess on average and the shear strength of loess modified by fly ash is 3.59% higher than that of the pure loess on average. The effect of the desulfurization ash on modifying the loess is better than that of the fly ash. When the mass ratio is 80:20, the shear strength of loess modified by the desulfurization ash is 9.15% higher than that of the fly ash on average. Comparing the results of the simulation calculation with the actual test results, the increase rate of the shear stress of the FLAC3D simulation is larger than that of the actual test, and the simulated shear strength is about 8.21% higher than the test shear strength.

scholarly journals Mechanical Properties and Micro Mechanism of Nano-Clay-Modified Soil Cement Reinforced by Recycled Sand

2021 ◽  
Vol 13 (14) ◽  
pp. 7758
Author(s):  
Biao Qian ◽  
Wenjie Yu ◽  
Beifeng Lv ◽  
Haibo Kang ◽  
Longxin Shu ◽  
...  
Keyword(s):  
Shear Strength ◽  
Void Ratio ◽  
Soil Mass ◽  
Direct Shear ◽  
Test Results ◽  
The Sustainable Development ◽  
Direct Shear Tests ◽  
Soil Cement ◽  
Nano Clay ◽  
New Material

To observe the effect of recycled sand and nano-clay on the improvement of the early strength of soil-cement (7d), 0%, 10%, 15% and 20% recycled sand were added. While maintaining a fixed moisture content of 30%, the ratios of each material are specified in terms of soil mass percentage. The shear strength of CSR (recycled sand blended soil-cement) was investigated by direct shear test and four groups of specimens (CSR-1, CSR-2, CSR-3 and CSR-4) were obtained. In addition, 8% nano-clay was added to four CSR groups to obtain the four groups of CSRN-1, CSRN-2, CSRN-3 and CSRN-4 (soil-cement mixed with recycled sand and nano-clay), which were also subjected to direct shear tests. A detailed analysis of the modification mechanism of soil-cement by recycled sand and nano-clay was carried out in combination with scanning electron microscopy (SEM) and IPP (ImagePro-Plus) software. The test results showed that: (1) CSR-3 has the highest shear strength due to the “concrete-like” effect of the incorporation of recycled sand. With the addition of 8% nano-clay, the overall shear strength of the cement was improved, with CSRN-2 having the best shear strength, thanks to the filling effect of the nano-clay and its high volcanic ash content. (2) When recycled sand and nano-clay were added to soil-cement, the improvement in shear strength was manifested in a more reasonable macroscopic internal structure distribution of soil-cement. (3) SEM test results showed that the shear strength was negatively correlated with the void ratio of its microstructure. The smaller the void ratio, the greater the shear strength. This shows that the use of reclaimed sand can improve the sustainable development of the environment, and at the same time, the new material of nano-clay has potential application value.

scholarly journals Comparison of Mechanical Properties of Fiber-Reinforced Sand under Triaxial Compression and Direct Shear

2015 ◽  
Vol 7 (1) ◽  
Author(s):  
Reza Noorzad ◽  
Seyed Taher Ghoreyshi Zarinkolaei
Keyword(s):  
Shear Strength ◽  
Axial Strain ◽  
Triaxial Compression ◽  
Polypropylene Fiber ◽  
Triaxial Tests ◽  
Direct Shear ◽  
Test Results ◽  
Peak Reduction ◽  
Shear Tests ◽  
Direct Shear Tests

AbstractThis research investigates the behavior of sand reinforced with polypropylene fiber. To do this, 40 direct shear tests and 40 triaxial tests were performed on the coastal beaches of Babolsar, a city in the North of Iran. The effect of parameters such as fiber content, length of fiber and normal or confining pressure on the behavior of Babolsar sand have been studied. In this study, four various fiber contents (0, 0.25, 0.5 and 1 percent), three different lengths of fiber (6, 12 and 18 mm) and four normal or confining pressures (50, 100, 200 and 400 kPa) have been employed. The test results show that fiber inclusion has a significant effect on the behavior of sand. In both direct shear and triaxial tests, the addition of fibers improved shear strength parameters (C, '), increased peak shear strength and axial strain at failure, and also limited the amount of post-peak reduction in shear resistance. The comparison of the test results revealed that due to better fiber orientation toward the direction of principal tensile strain in triaxial test as compared to direct shear tests, the fiber efficiency and its effect on soil behavior is much more significant in triaxial specimens.

Mechanical Properties of Fly Ash-Slag-Dredged Silt System Stimulated by Alkali

2013 ◽  
Vol 807-809 ◽  
pp. 1140-1146 ◽  
Author(s):  
Yi Xuan Chen ◽  
Xiu Li Sun ◽  
Zhi Hua Li
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Fly Ash ◽  
Construction Materials ◽  
Xrd Analysis ◽  
Test Results ◽  
X Ray Diffraction ◽  
Shear Tests ◽  
X Ray ◽  
Direct Shear Tests

The objective of this work is to investigate the stimulation effect of the addition of alkali on the fly ash and slag for stabilizing dredged silt. Based on the test results, a viable alternative for the final disposal of dredged silt as subgrade construction materials were proposed. For this purpose, several mixtures of dredged silt-fly ash-slag and alkali were prepared and stabilized/solidified. In this system, fly ash and slag were used as hardening agents (solidified materials) of dredged silt and alkali was used as activator of fly ash and slag. The shear strength of the mixture was tested by several direct shear tests. Furthermore, X-Ray Diffraction (XRD) analysis was used to determine the hydration products of the system. The specimens were tested in order to determine the shear strength changes versus hydration time and the alkali content. It is indicated that mechanical properties of solidified silt are improved significantly by addition of fly ash and slag stimulated by alkali.

scholarly journals Shear strength behaviour of sand-bentonite mixtures with pumice additivite under high temperature

2020 ◽  
Vol 205 ◽  
pp. 04004
Author(s):  
Esra Güneri ◽  
Yeliz Yükselen Aksoy
Keyword(s):  
Shear Strength ◽  
High Temperature ◽  
Room Temperature ◽  
Engineering Properties ◽  
Direct Shear ◽  
Test Results ◽  
Soil Behavior ◽  
Shear Tests ◽  
Volume Deformation ◽  
Direct Shear Tests

Depending on increase in the number and type of energy geostructures, studies on the change in soil behavior against heat increase becomes more important. The engineering properties such as permeability, volume deformation of surrounding soils around energy structures mustn’t alter in the presence of heat and thermal cycles. Pumice is a material used in many fields especially for thermal insulation. For that reason, pumice can be used for increasing the resistance of soils in the presence of heat. In this study, the shear strength behavior of sand-bentonite mixtures was investigated with pumice additive under high temperature. In the experiments, 10% and 20% pumice were added to 10% and 20% sand-bentonite mixtures and compaction, direct shear tests were conducted. The direct shear tests were performed both room temperature and under 80°C. The results have shown that the pumice additive increased the shear strength of sand-bentonite mixtures under high temperature when compared the test results under room temperature.

Influence of Density on the Hydraulic and Mechanical Properties of Sands

2014 ◽  
Vol 580-583 ◽  
pp. 659-664
Author(s):  
Osvaldo de Freitas Neto ◽  
Olavo Francisco dos Santos Jr. ◽  
Ricardo Nascimento Flores Severo
Keyword(s):  
Shear Strength ◽  
Hydraulic Conductivity ◽  
Triaxial Compression ◽  
Friction Angle ◽  
Coarse Fraction ◽  
Direct Shear ◽  
Direct Shear Tests ◽  
Strength Tests ◽  
Constant Head ◽  
Direct Shear Testing

This article aims at assessing the influence of relative density on the hydraulic conductivity and shear strength of two sands, denominated S01 and S02, derived from different regions and formation processes. S01 is wind-blown and S2 alluvial. The results of characterization and hydraulic conductivity in constant head tests were presented for both samples. The results of direct shear tests with sand S01 prepared with 5 different void ratios were also presented, for a vertical stress of 100kPa. The S02 sample was prepared with 4 different void ratios and these underwent direct shear testing with vertical stresses of 25kPa and 150kPa. This sample was prepared with the maximum and minimum void ratio and submitted to strength tests at CD triaxial compression with confining stresses of 50kPa, 100kPa and 200kPa. Results showed that even with different grain sizes, and under different density conditions, there were no significant variations in the permeability of the materials. With respect to shear strength, sand S01 obtained higher angle of friction values than sand S02, even though the latter had a higher percent coarse fraction. Sand S02 was relatively similar in terms of friction angle values obtained in direct shear and triaxial compression strength tests.

scholarly journals Analisis Kestabilan Lereng Berdasarkan Kekuatan Geser Massa Batuan Terhadap Perubahan Kandungan Air Pada Tambang Batubara Di Area Blok Menyango

PROMINE ◽  
2019 ◽  
Vol 7 (2) ◽  
pp. 71-77
Author(s):  
Novandri Kusuma Wardana
Keyword(s):  
Shear Strength ◽  
Natural Condition ◽  
Shear Failure ◽  
Friction Angle ◽  
Direct Shear ◽  
Test Results ◽  
Shear Tests ◽  
Direct Shear Tests ◽  
Wet Condition ◽  
The Impact

Mining activities is commonly to work with the problem of stability of rock mass, then befordesaining mine’s slope should know rock shear strength parameters, such as cohesion (c) andinternal friction angle value ( . Beside those parameters, also needed to know the impact ofwater content to the rocks. The water content will effect rock’s shear strength, proof by the rockcondition which is ductile when it is dry and soft when it is wet. Based on test results was doneusing sandstone with laboratory scale of direct shear test were analyzed using mohr – coulomband patton criteria (1966). It is known that the cohesion (c) of sandstone decreased from 510,35kPa at natural condition down to 133,75 kPa at wet condition. The internal friction angle ( ) alsodecreased from 54,56° at natural condition down to 48,45° at wet condition. The reduction of theshear strength is caused by fragments and clay minerals characteristics which are so reactiveand very easy to absorb water so that the cohesion of the sandstone reduce the active normalstress so that working the shear stress required to cause the shear failure becomeweaker. From the results, it is also known that the shear surface roughness had a lot ofinfluence on the shear strength the normal stresses applied on the direct shear tests werevery low under 20% of UCS.

scholarly journals The Mechanical Properties of Fly-Ash-Stabilized Sands

Geosciences ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 132 ◽  
Author(s):  
Minson Simatupang ◽  
Lukas Kano Mangalla ◽  
Romy Suryaningrat Edwin ◽  
Adris Ade Putra ◽  
Muhammad Thahir Azikin ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Fly Ash ◽  
Sample Preparation ◽  
Degree Of Saturation ◽  
Direct Shear ◽  
Curing Time ◽  
Grain Sizes ◽  
Strength Tests ◽  
Strength And Stiffness

The stabilization of soil through the addition of fly ash has been shown to be an effective alternative for improving the strength and stiffness of soil through the resulting chemical reactions. The chemical reaction that occurs dissociates the lime (CaO) in the fly ash, and the establishment of cementitious and pozzolanic gels (consisting of calcium silicate hydrate (CSH) gel and calcium aluminate hydrate (CAH) gel) binds the soil particles and increases the strength and stiffness of the soil. Investigations into the mechanical properties of sands stabilized with fly ash (fly-ash-stabilized sands) were conducted through a series of unconfined compressive strength (UCS) and direct shear strength tests for various fly ash percentages, curing times, grain sizes, degrees of saturation during sample preparation, and content of fines. It was found that the mechanical properties—UCS and direct shear strength (DSS)—of fly-ash-stabilized sands increased with both increasing fly ash content in the specimen and curing time, but decreased with increasing grain size, degree of saturation during sample preparation, and content of fines. The results indicated that fly-ash-stabilized sands required more than a month to attain their optimum performance with regard to binding sand particles.

scholarly journals Direct Shear Test on Coarse Gap-Graded Fill: Plate Opening Size and Its Effect on Measured Shear Strength

2020 ◽  
Vol 2020 ◽  
pp. 1-13 ◽  
Author(s):  
H. Cai ◽  
R. Wei ◽  
J. Z. Xiao ◽  
Z. W. Wang ◽  
J. Yan ◽  
...  
Keyword(s):  
Shear Strength ◽  
Large Scale ◽  
Fine Particles ◽  
Triaxial Compression ◽  
Direct Shear ◽  
Test Results ◽  
Compression Tests ◽  
Construction Sites ◽  
Direct Shear Tests ◽  
Soil Mixtures

In this paper, three different rock-soil mixtures were reconstituted in laboratory, which were designed to mimic the proportions of coarse and fine particles in the high fill used at the airport construction sites. The shear strength of the reconstituted mixtures was determined by both large-scale direct shear tests (DSTs) with different plate opening sizes and triaxial compression tests. By comparing the test results, the most appropriate plate opening size for DSTs on coarse gap-graded rock-soil mixtures is discussed. The test results indicate that the opening size has a significant effect on the measured shear strength of gap-graded rock-soil mixtures. For DSTs under the same normal stress, the peak strength decreases with increasing plate opening size. For the gap-graded mixture with a small proportion of coarse particles, a plate opening size of one-third to one-quarter of the maximum particle size (dmax) is suitable. With a higher coarse particle content, the opening size should be increased appropriately. If the percentage of gravels (5.0 mm < d < 20.0 mm) is more than 47%, a plate opening size of slightly greater or less than one-half dmax is more appropriate.

Sign in / Sign up

Export Citation Format

Share Document