scholarly journals Analysis of Measured Parameters in Relation to the Amount of Fibre in Lightweight Red Ceramic Waste Aggregate Concrete

Mathematics ◽  
2022 ◽  
Vol 10 (2) ◽  
pp. 229
Author(s):  
Marie Horňáková ◽  
Petr Lehner
Keyword(s):  
Modulus Of Elasticity ◽  
Test Methods ◽  
Fibre Reinforcement ◽  
Ceramic Waste ◽  
Destructive Test ◽  
Correlation And Regression Analysis ◽  
Regression Curves ◽  
Static Modulus ◽  
Static Modulus Of Elasticity ◽  
Non Destructive

The present study provides a correlation and regression analysis of lightweight waste aggregate concretes with varying degrees of fibre reinforcement. The concrete mix contains pre-soaked red ceramic waste aggregate, expanded clay coarse aggregate and Portland cement. Copper-coated crimped steel fibre was used as the reinforcement. The experimental results included properties measured by destructive test methods—compressive strength, splitting tensile strength, static modulus of elasticity, the limit of proportionality, shear strength; and by non-destructive test methods—dynamic modulus of elasticity and surface electrical resistivity. These properties were analysed to study the relevancy and significance between non-destructive and destructive methods of measurement in the case of different amounts of fibre. The results show differences in the degree of fit to the linear and quadratic regression curves for pairs of destructive and non-destructive test results. As expected, the linear relationship can be applied in a few cases, but the quadratic curve must be used for a few pairs. Another observation is that it is not possible to neglect the amount of fibre in the correlation analyses of the measured properties.

Experimental Analysis of the Development of Compressive Strength, Modulus of Elasticity and Acoustic Emission Parameters of Alkali-Activated Composites

2018 ◽  
Vol 760 ◽  
pp. 266-271
Author(s):  
Dalibor Kocáb ◽  
Libor Topolář ◽  
Vlastimil Bílek Jr. ◽  
Barbara Kucharczyková ◽  
Michaela Hoduláková ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Acoustic Emission ◽  
Modulus Of Elasticity ◽  
Stress Test ◽  
Ultrasonic Pulse ◽  
Static Modulus ◽  
Activated Slag ◽  
Static Modulus Of Elasticity ◽  
Non Destructive ◽  
Alkali Activated

This paper describes an experiment focused on monitoring the development of the modulus of elasticity and the compressive strength of composites that are based on alkali‑activated slag (AAS) during the first 28 days of ageing. The test specimens were tested at the age of 3 and 28 days using two non-destructive methods (ultrasonic pulse and resonance methods) to determine the value of the dynamic modulus of elasticity. Subsequently, the same specimens were used to determine the static modulus of elasticity using compressive stress test, during which the behaviour of the composite was monitored by equipment for recording the acoustic emission in the material. The result of the experiment is the evaluation of the behaviour of the AAS composite in regard to the development of its modulus of elasticity and compressive strength, as well as in regard to the acoustic emission method during loading.

scholarly journals Prediction of the Static Modulus of Elasticity Using Four non Destructive Testing

2014 ◽  
Vol 13 (1) ◽  
pp. 33-40 ◽  
Author(s):  
Hugo Luis Chávez-García ◽  
Elia Mercedes Alonso-Guzmán ◽  
Wilfrido Martínez-Molina ◽  
Mario Graff ◽  
J. C Arteaga-Arcos
Keyword(s):  
Modulus Of Elasticity ◽  
Non Destructive Testing ◽  
Destructive Testing ◽  
Static Modulus ◽  
Static Modulus Of Elasticity ◽  
Non Destructive

scholarly journals Concrete Compressive Strength by Means of Ultrasonic Pulse Velocity and Moduli of Elasticity

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 7018
Author(s):  
Bogdan Bolborea ◽  
Cornelia Baera ◽  
Sorin Dan ◽  
Aurelian Gruin ◽  
Dumitru-Doru Burduhos-Nergis ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Modulus Of Elasticity ◽  
Pulse Velocity ◽  
High Rate ◽  
Dry Density ◽  
Concrete Compressive Strength ◽  
Static Modulus ◽  
Static Modulus Of Elasticity ◽  
Non Destructive ◽  
Moduli Of Elasticity

Developing non-destructive methods (NDT) that can deliver faster and more accurate results is an objective pursued by many researchers. The purpose of this paper is to present a new approach in predicting the concrete compressive strength through means of ultrasonic testing for non-destructive determination of the dynamic and static modulus of elasticity. For this study, the dynamic Poisson’s coefficient was assigned values provided by technical literature. Using ultra-sonic pulse velocity (UPV) the apparent density and the dynamic modulus of elasticity were determined. The viability of the theoretical approach proposed by Salman, used for the air-dry density determination (predicted density), was experimentally confirmed (measured density). The calculated accuracy of the Salman method ranged between 98 and 99% for all the four groups of specimens used in the study. Furthermore, the static modulus of elasticity was deducted through a linear relationship between the two moduli of elasticity. Finally, the concrete compressive strength was mathematically determined by using the previously mentioned parameters. The accuracy of the proposed method for concrete compressive strength assessment ranged between 92 and 94%. The precision was established with respect to the destructive testing of concrete cores. For this research, the experimental part was performed on concrete cores extracted from different elements of different structures and divided into four distinct groups. The high rate of accuracy in predicting the concrete compressive strength, provided by this study, exceeds 90% with respect to the reference, and makes this method suitable for further investigations related to both the optimization of the procedure and = the domain of applicability (in terms of structural aspects and concrete mix design, environmental conditions, etc.).

Determining elastic properties of sedimentary strata in terms of limestone samples by laser ultrasonics

2020 ◽  
pp. 125-134
Author(s):  
I. A. Shibaev ◽  
V. A. Vinnikov ◽  
G. D. Stepanov
Keyword(s):  
Physical And Mechanical Properties ◽  
Laser Ultrasonics ◽  
Compression Tests ◽  
S Waves ◽  
Static Modulus ◽  
Enhance Efficiency ◽  
Static Modulus Of Elasticity ◽  
Static Elastic Moduli ◽  
Non Destructive ◽  
Moduli Of Elasticity

Geological engineering often uses geomechanical modeling aimed to enhance efficiency of mining or performance of structures. One of the input parameters for such models are the static elastic moduli of rocks. This article presents the studies into the physical and mechanical properties of rocks-limestone of non-metamorphic diagenesis. The precision measurements of Pand S-waves are carried out to an accuracy of 0.2% by laser ultrasonics. The static moduli of elasticity and the deformation characteristics of rocks are determined in the uniaxial compression tests by the standards of GOST 21153.2-84 and GOST 28985-91, respectively. The correlation dependence is found between the static and dynamic elasticity moduli in limestone samples. The found correlation allows drawing the conclusion that the static modulus of elasticity can be estimated in non-destructive tests, which largely simplifies preliminary diagnostics of samples in case of limited number of test core.

Nondestructive Evaluation of Red Oak and White Oak Species

2020 ◽  
Vol 70 (3) ◽  
pp. 370-377
Author(s):  
Cristian Grecca Turkot ◽  
Roy Daniel Seale ◽  
Edward D. Entsminger ◽  
Frederico José Nistal França ◽  
Rubin Shmulsky
Keyword(s):  
Modulus Of Elasticity ◽  
Longitudinal Vibration ◽  
Mechanical Tests ◽  
Modulus Of Rupture ◽  
Red Oak ◽  
Quercus Alba ◽  
White Oak ◽  
Static Modulus ◽  
Static Modulus Of Elasticity ◽  
The Relationship

Abstract The objective of this article is to evaluate the relationship between the dynamic modulus of elasticity (MOEd), which was obtained with acoustic-based nondestructive testing (NDT) methods, and static bending properties of two domestic hardwood oak species. The mechanical properties were conducted using static modulus of elasticity (MOE) and modulus of rupture (MOR) in radial and tangential directions. Mechanical tests were performed according to ASTM D143 on small clear, defect-free specimens from the two tree species: red oak (Quercus rubra) and white oak (Quercus alba). The MOEd was determined by two NDT methods and three longitudinal vibration methods based on the fast Fourier transform. The destructive strength values obtained in this study were within the expected range for these species. The MOE was best predicted by NDT methods for both species but also had a strong capability to predict MOR.

scholarly journals Influence of Hybrid Fibers on Toughness Behavior of High Strength Flowing Concrete

2011 ◽  
Vol 57 (3) ◽  
pp. 249-260 ◽  
Author(s):  
Eethar Thanon Dawood ◽  
Mahyuddin Ramli
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Hybrid Composite ◽  
High Strength ◽  
Steel Fibers ◽  
Hybrid Fibers ◽  
Static Modulus ◽  
Static Modulus Of Elasticity ◽  
Strength And Toughness

Abstract This study investigates the use of steel fibers and hybrid composite with a total fibers content of 2% on the high strength flowing concrete and determines the density, compressive strength, static modulus of elasticity, flexural strength and toughness indices for the mixes. The results show that the inclusion of more than 0.5% of palm fibers in hybrid fibers mixes reduces the compressive strength. The hybrid fibers can be considered as a promising concept and the replacement of a portion of steel fibers with palm fibers can significantly reduce the density, enhance the flexural strength and toughness. The results also indicates that the use of hybrid fibers (1.5 steel fibers + 0.5% palm fibers) in specimens increases significantly the toughness indices and thus the use of hybrid fibers combinations in reinforced concrete would enhance their flexural toughness & rigidity and enhance their overall performances

Sign in / Sign up

Export Citation Format

Share Document