scholarly journals Calibration Method of Accelerometer Based on Rotation Principle Using Double Turntable Centrifuge

Micromachines ◽  
2021 ◽  
Vol 13 (1) ◽  
pp. 62
Author(s):  
Xianshan Dong ◽  
Xinlong Huang ◽  
Guizhen Du ◽  
Qinwen Huang ◽  
Yixiong Huang ◽  
...  
Keyword(s):  
Calculation Method ◽  
Calibration Method ◽  
Calibration Procedure ◽  
Scale Factor ◽  
Centripetal Acceleration ◽  
Mems Accelerometer ◽  
Key Technology ◽  
Acceleration Vector ◽  
Back Calculation ◽  
Input Acceleration

For linear accelerometers, calibration with a precision centrifuge is a key technology, and the input acceleration imposed on the accelerometer should be accurately obtained in the calibration. However, there are often errors in the installation of sample that make the calibration inaccurate. To solve installation errors and obtain the input acceleration in the calibration of the accelerometer, a calibration method based on the rotation principle using a double turntable centrifuge is proposed in this work. The key operation is that the sub-turntable is rotated to make the input axis of the accelerometer perpendicular to the direction of the centripetal acceleration vector. Models of installation errors of angle and radius were built. Based on these models, the static radius and input acceleration can be obtained accurately, and the calibration of the scale factor, nonlinearity and asymmetry can be implemented. Using this method, measurements of the MEMS accelerometer with a range of ±30 g were carried out. The results show that the discrepancy of performance obtained from different installation positions was smaller than 100 ppm after calibrating the input acceleration. Moreover, the results using this method were consistent with those using the back-calculation method. These results demonstrate that the effectiveness of our proposed method was confirmed. This method can measure the static radius directly eliminating the installation errors of angle and radius, and it simplifies the accelerometer calibration procedure.

Back-Calculation Method of Subgrade Modulus Based on Traffic Speed Deflectometer

CICTP 2020 ◽  
2020 ◽  
Author(s):  
Guoshuai Zang ◽  
Haizhu Lu ◽  
Guanglai Jin ◽  
Zhixiang Zhang
Keyword(s):  
Calculation Method ◽  
Back Calculation ◽  
Subgrade Modulus ◽  
Traffic Speed

scholarly journals A Low-g MEMS Accelerometer with High Sensitivity, Low Nonlinearity and Large Dynamic Range Based on Mode-Localization of 3-DoF Weakly Coupled Resonators

Micromachines ◽  
2021 ◽  
Vol 12 (3) ◽  
pp. 310
Author(s):  
Muhammad Mubasher Saleem ◽  
Shayaan Saghir ◽  
Syed Ali Raza Bukhari ◽  
Amir Hamza ◽  
Rana Iqtidar Shakoor ◽  
...  
Keyword(s):  
Microelectromechanical Systems ◽  
Dynamic Range ◽  
Proof Mass ◽  
Amplitude Ratio ◽  
Silicon On Insulator ◽  
Coupled Resonators ◽  
Mode Localization ◽  
Mems Accelerometer ◽  
Weakly Coupled ◽  
Input Acceleration

This paper presents a new design of microelectromechanical systems (MEMS) based low-g accelerometer utilizing mode-localization effect in the three degree-of-freedom (3-DoF) weakly coupled MEMS resonators. Two sets of the 3-DoF mechanically coupled resonators are used on either side of the single proof mass and difference in the amplitude ratio of two resonator sets is considered as an output metric for the input acceleration measurement. The proof mass is electrostatically coupled to the perturbation resonators and for the sensitivity and input dynamic range tuning of MEMS accelerometer, electrostatic electrodes are used with each resonator in two sets of 3-DoF coupled resonators. The MEMS accelerometer is designed considering the foundry process constraints of silicon-on-insulator multi-user MEMS processes (SOIMUMPs). The performance of the MEMS accelerometer is analyzed through finite-element-method (FEM) based simulations. The sensitivity of the MEMS accelerometer in terms of amplitude ratio difference is obtained as 10.61/g for an input acceleration range of ±2 g with thermomechanical noise based resolution of 0.22 and nonlinearity less than 0.5%.

Multi-Position Self-Calibration Method of Inertial Navigation System

2012 ◽  
Vol 580 ◽  
pp. 146-150
Author(s):  
Ji Wei Zhang ◽  
Xiao Dong Xu ◽  
Bo Wang
Keyword(s):  
Navigation System ◽  
Horizontal Plane ◽  
Inertial Navigation System ◽  
Inertial Navigation ◽  
Calibration Method ◽  
Scale Factor ◽  
Self Calibration ◽  
Attitude Angle ◽  
On Line

In order to solve the problem that in the dual axle rotating modulation inertial navigation system the angle between the horizon roller of the system and horizontal plane can't be removed, this paper provides an on-line self calibration method based on inertial navigation system, and this method realized the on-line self calibration of the inertial navigation system by calculating bias and scale factor both of the gyroscope and accelerometer, solving the problem that in the dual axle rotating modulation inertial navigation system the angle between the horizon roller of the system and horizontal plane can't be removed, providing an calculable basis for the prediction of attitude angle and realizing on-line autonomous self-calibration.

scholarly journals Non-destructive Dielectric Measurements and Calibration for Thin Materials Using Waveguide-Coaxial Adaptors

2014 ◽  
Vol 14 (1) ◽  
pp. 16-24 ◽  
Author(s):  
K. Y. You ◽  
Z. Abbas ◽  
M. F. A. Malek ◽  
E. M. Cheng
Keyword(s):  
Calibration Method ◽  
Calibration Procedure ◽  
Reflection Coefficients ◽  
Dielectric Measurements ◽  
Finite Samples ◽  
Open Standard ◽  
Rectangular Waveguides ◽  
Standard Values ◽  
Calibration Techniques ◽  
Non Destructive

Abstract This paper focuses on the calibration of apertures for rectangular waveguides using open-short-load (OSL) standards and transmission-line (TL) approaches. The reflection coefficients that were measured using both calibration techniques were compared with the coefficients acquired using the thru-reflect-line (TRL) method. In this study, analogous relationships between the results of OSL calibration and TL calibration were identified. In the OSL calibration method, the theoretical, open-standard values are calculated from quasi-static integral models. The proposed TL calibration procedure is a simple, rapid, broadband approach, and its results were validated by using the OSL calibration method and by comparing the results with the calculated integral admittance. The quasi-static integral models were used to convert the measured reflection coefficients to relative permittivities for the infinite samples and the thin, finite samples

THE CALIBRATION OF AN ARRAY OF ACCELEROMETERS

2011 ◽  
Vol 35 (2) ◽  
pp. 251-267 ◽  
Author(s):  
Dany Dubé ◽  
Philippe Cardou
Keyword(s):  
Angular Velocity ◽  
Rigid Body ◽  
Least Squares ◽  
Calibration Method ◽  
Calibration Procedure ◽  
Rigid Bodies ◽  
New Method ◽  
Scale Factors ◽  
Array Calibration ◽  
The One

An accelerometer-array calibration method is proposed in this paper by which we estimate not only the accelerometer offsets and scale factors, but also their sensitive directions and positions on a rigid body. These latter parameters are computed from the classical equations that describe the kinematics of rigid bodies, and by measuring the accelerometer-array displacements using a magnetic sensor. Unlike calibration schemes that were reported before, the one proposed here guarantees that the estimated accelerometer-array parameters are globally optimum in the least-squares sense. The calibration procedure is tested on OCTA, a rigid body equipped with six biaxial accelerometers. It is demonstrated that the new method significantly reduces the errors when computing the angular velocity of a rigid body from the accelerometer measurements.

Convenient Calibration Procedure for Structured Light Projection System

2013 ◽  
Vol 662 ◽  
pp. 777-780
Author(s):  
Wen Guo Li ◽  
Shao Jun Duan
Keyword(s):  
Relative Position ◽  
Structured Light ◽  
Calibration Method ◽  
Calibration Procedure ◽  
Shape Measurement ◽  
Projection System ◽  
System Calibration ◽  
3D Shape ◽  
3D Shape Measurement ◽  
Projector Calibration

We present a convenient calibration method for structured light projection system. The proposed clibration approach can realize 3D shape measurement without projector calibration, without system calibration, without precise linear z stage to be used, the relative position between camera and projector can be arbitrary, and the only involved device is a plane board. Experiment results validated that the accuracy of the proposed approach.

Sign in / Sign up

Export Citation Format

Share Document