scholarly journals Humidification–Dehumidification (HDH) Desalination and Other Volume Reduction Techniques for Produced Water Treatment

Water ◽  
2021 ◽  
Vol 14 (1) ◽  
pp. 60
Author(s):  
Majeda Khraisheh ◽  
Mehreen Inamdar ◽  
Fares AlMomani ◽  
Samer Adham
Keyword(s):  
Water Treatment ◽  
Produced Water ◽  
Volume Reduction ◽  
Power Cycles ◽  
Freeze Concentration ◽  
Reduction Techniques ◽  
Large Bulk ◽  
Present Solution ◽  
Novel Method ◽  
Desalination Technology

Volume reduction has been suggested as a novel method to tackle the various challenges associated with produced water. The present solution offers an economical and environmentally friendly solution to treat a large bulk of produced water that may overwhelm conventional water treatment methods. The current study provides a review of the various volume reduction technologies including freeze concentration, reverse osmosis, and humidification and dehumidification desalination systems. Focus is concentrated on the general HDH technologies in addition to its integration with refrigeration cycles for conditioned air production, and the power cycles for power generation. The GOR, freshwater yield, and efficiencies of the integrated HDH systems were reviewed. Lastly, innovation in the HDH desalination technology is discussed with emphasis on its incorporation with the MVC process.

Progressive Freeze Concentration for Volume Reduction of Produced Water and Biodiesel Wastewater

2019 ◽  
Vol 42 (9) ◽  
pp. 1764-1770 ◽  
Author(s):  
Shafirah Samsuri ◽  
Nor Aman Nor Rizan ◽  
Siew Hzien Hung ◽  
Nurul Aini Amran ◽  
Nonni Soraya Sambudi
Keyword(s):  
Produced Water ◽  
Volume Reduction ◽  
Freeze Concentration ◽  
Biodiesel Wastewater

Application of three different water treatment technologies to shale gas produced water

2016 ◽  
Vol 20 (2) ◽  
pp. 104-110 ◽  
Author(s):  
Eunyoung Jang ◽  
Seongpil Jeong ◽  
Eunhyea Chung
Keyword(s):  
Water Treatment ◽  
Shale Gas ◽  
Produced Water ◽  
Treatment Technologies

Mass Transfer in Tubular Ceramic Membranes for Polluted Water Treatment - Numerical Simulation

2018 ◽  
Vol 20 ◽  
pp. 16-33 ◽  
Author(s):  
J. Saraiva de Souza ◽  
S. José dos Santos Filho ◽  
Severino Rodrigues de Farias Neto ◽  
A.G. Barbosa de Lima ◽  
H.A. Luma Fernandes Magalhães
Keyword(s):  
Mass Transfer ◽  
Water Treatment ◽  
Produced Water ◽  
Ceramic Membrane ◽  
Porous Ceramic ◽  
Ceramic Membranes ◽  
Numerical Results ◽  
Polluted Water ◽  
Separation Processes ◽  
Water Separation

Innovative technologies are needed to attend the increasingly strict requirements for produced water treatment, since most of the separation processes are limited to particles larger than 10 μm. Separation processes using ceramic membranes are attracting great interest from academic and industrial community. Nevertheless, few studies, especially numerical, regarding the inorganic membrane’s application for the polluted water separation have been reported. In the present work, therefore, a study of fluid-flow dynamics for a laminar regime in porous tubes (tubular porous ceramic membrane) has been performed. The mass, momentum and mass transport conservation equations were solved with the aid of a structured mesh using ANSYS CFX commercial package. The velocity of local permeation was determined using the resistance in series model. The specific resistance of the polarized layer was obtained by Carman-Kozeny equation. The numerical results were evaluated and compared with the results available in the literature, where by a good agreement with each other was found. The numerical results, obtained by the proposed shell and tubular membrane separation module, indicate that there is facilitation of mass transfer and hence a reduction in the thickness of the polarized boundary layer occurs.

scholarly journals Hydrophylicity Enhancement of Modified Cellulose Acetate Membrane to Improve the Membrane Performance in Produced Water Treatment

2018 ◽  
Vol 156 ◽  
pp. 08003 ◽  
Author(s):  
Tutuk Djoko Kusworo ◽  
Danny Soetrisnanto ◽  
Cynthia Santoso ◽  
Tyas Dwi Payanti ◽  
Dani Puji Utomo
Keyword(s):  
Water Treatment ◽  
Produced Water ◽  
Uv Light ◽  
Light Exposure ◽  
Membrane Surface ◽  
Asymmetric Structure ◽  
Dense Layer ◽  
Cellulose Acetate Membrane ◽  
Permeate Flux ◽  
Produced Water Treatment

Produced water is a wastewater generated from petroleum industry with high concentration of pollutants such as Total Dissolved Solid, Organic content, and Oil and grease. Membrane technology has been currently applied for produced water treatment due to its efficiency, compact, mild and clean process. The main problem of produced water using membrane is fouling on the membrane surface which causes on low permeate productivity. This paper is majority focused on the improvement of anti-fouling performance through several modifications to increase CA membrane hydrophilicity. The membrane was prepared by formulating the dope solution consists of 18 wt-% CA polymer, acetone, and PEG additive (3 wt-%, 5 wt-%, and 7 wt-%). The membranes are casted using NIPS method and being irradiated under UV light exposure. The SEM images show that parepared membrane has asymmetric structure consist of dense layer, intermediete layer, and finger-like support layer. The filtration test shows that PEG addition increase the membrane hydrophilicity and the permeate flux increases. UV light exposure on the membrane improves the membrane stability and hydrophilicity. The imrpovement of membrane anti-fouling performance is essential to achieve the higher productivity without lowering its pollutants rejection.

Cost-Efficient De-Bottlenecking of Produced Water Treatment Systems through the Application of a Single Technology, Eliminating the Need for Hydrocyclones and Degassing Drums

2021 ◽  
Author(s):  
Steinar Asdahl ◽  
Johann Jansen van Rensburg ◽  
Martin Einarson Waag ◽  
Rune Glenna Nilssen
Keyword(s):  
Water Treatment ◽  
Produced Water ◽  
Separation Efficiency ◽  
Water System ◽  
Treatment Technology ◽  
Two Stage ◽  
Water Separation ◽  
Design Capacity ◽  
New Process ◽  
Produced Water Treatment

Abstract Traditionally, produced water from production separators is handled by multiple steps and different technologies in order to meet the required quality for either discharge or reinjection of the water. The development of the latest Compact Flotation Unit (CFU) technology has unlocked the potential for savings on cost, complexity, footprint and weight for the produced water treatment system. The developed CFU technology has proven applicable through field testing as a single treatment technology for reducing Oil-in-Water (OiW) content directly from tie-in at separator and still meet stringent requirements for outlet OiW quality. Field tests were conducted with inlet OiW concentration ranging from 200-2000 ppm, achieving results in the range 2.5 to 21 ppm only with a two-stage latest generation CFU. Compared to a traditional produced water system setup consisting of de-oiling hydrocyclones and a horizontal degassing vessel, the savings in footprint and operational weight is estimated to 54 % and 53 % respectively utilizing a two-stage CFU for a system with a design capacity of 76.000 BWPD. Furthermore, the development of the latest generation CFU technology has enabled the retrofit concept, incorporating the developed CFU internals into existing gravity separation based produced water vessels, converting them to more efficient flotation vessels with increased capacity. For brownfield and debottlenecking applications, operators are challenged by increasing water cut from maturing wells, and as a result exceeding the facilities design capacity for produced water treatment. This challenge is often further reinforced by increasingly stricter environmental legislation for OiW content for discharge or re-injection. The retrofit concept will offer a highly cost-, footprint- and weight-efficient solutions to these challenges utilizing existing vessels. Benefits of the retrofit concept: Bring proven and unique performance of the technology to other produced water separation vessels helping the operators improve the separation efficiency and increase throughput while meeting discharge requirementsShort execution time compared to installation of new process equipmentLow cost compared to installation of new process equipmentUtilization of existing equipment saves valuable footprint.

Sign in / Sign up

Export Citation Format

Share Document