scholarly journals Investigation of Structural, Morphological, Resistivity of Novel Electrical Insulator: Industrial Wastes

2021 ◽  
pp. 51-58
Author(s):  
Panigrahi M.K
Keyword(s):  
Room Temperature ◽  
Thermo Gravimetric Analysis ◽  
Dielectric Behavior ◽  
Industrial Wastes ◽  
Uniaxial Pressure ◽  
Diffraction Field ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
Electrical Insulator ◽  
China Clay

In the present study, the effect of china clays on the sintering, strength and dielectric behavior of electrical ceramic fly ash/china clay (FA/CC) composite insulator is investigated. The different composition of samples containing different china clay (CC) contents of 10, 20, 30, 40, and 50 % are prepared using the uniaxial pressure technique applying 10 MPa pressure. At 1200 °C, for the composition having 40 wt% china clays, the maximum resistivity is calculated and is 39.5 × 107 Ωm. The composite is highly competence with china clays-based insulators. Further, the prepared composite is also analysed using different characterization technique such as x-ray diffraction, field emission scanning electron microscopy with energy dispersive analysis, fourier transformation infra-red spectroscopy, dielctric, and thermo gravimetric analysis. Frequency dielectric value of the composite is estimated at room temperature in the frequency range of 1-500 kHz at room temperature. According to the resistivity and dielectric properties, the composite has enormous potential for the electrical insulator application.

scholarly journals Rapid four-component synthesis of dihydropyrano[2,3-c]pyrazoles using nano-eggshell/Ti(IV) as a highly compatible natural based catalyst

BMC Chemistry ◽  
2021 ◽  
Vol 15 (1) ◽  
Author(s):  
Arefeh Dehghani Tafti ◽  
Bi Bi Fatemeh Mirjalili ◽  
Abdolhamid Bamoniri ◽  
Naeimeh Salehi
Keyword(s):  
Thermo Gravimetric Analysis ◽  
Reaction Times ◽  
Diffraction Field ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Solvent Free Conditions ◽  
High Yields ◽  
Work Up

AbstractNano-eggshell/Ti(IV) as a novel naturally based catalyst was prepared, characterized and applied for the synthesis of dihydropyrano[2,3-c]pyrazole derivatives. The characterization of nano-eggshell/Ti(IV) was performed using Fourier Transform Infrared spectroscopy, X-ray Diffraction, Field Emission Scanning Electron Microscopy, Energy-Dispersive X-ray Spectroscopy, and Thermo Gravimetric Analysis. Dihydropyrano[2,3-c]pyrazoles were synthesized in the presence of nano-eggshell/Ti(IV) via a four component reaction of aldehydes, ethyl acetoacetate, malononitrile and hydrazine hydrate at room temperature under solvent free conditions. The principal affairs of this procedure are mild condition, short reaction times, easy work-up, high yields, reusability of the catalyst and the absence of toxic organic solvents.

In-situ stabilization of silver nanoparticles in polymer hydrogels for enhanced catalytic reduction of macro and micro pollutants

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Luqman Ali Shah ◽  
Rida Javed ◽  
Mohammad Siddiq ◽  
Iram BiBi ◽  
Ishrat Jamil ◽  
...  
Keyword(s):  
Catalytic Reduction ◽  
Thermo Gravimetric Analysis ◽  
Activation Parameters ◽  
Reduction Reaction ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
In Situ Stabilization ◽  
Hybrid Hydrogels ◽  
Kinetics Of

AbstractThe in-situ stabilization of Ag nanoparticles is carried out by the use of reducing agent and synthesized three different types of hydrogen (anionic, cationic, and neutral) template. The morphology, constitution and thermal stability of the synthesized pure and Ag-entrapped hybrid hydrogels were efficiently confirmed using scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD) and thermo gravimetric analysis (TGA). The prepared hybrid hydrogels were used in the decolorization of methylene blue (MB) and azo dyes congo red (CR), methyl Orange (MO), and reduction of 4-nitrophenol (4-NP) and nitrobenzene (NB) by an electron donor NaBH4. The kinetics of the reduction reaction was also assessed to determine the activation parameters. The hybrid hydrogen catalysts were recovered by filtration and used continuously up to six times with 98% conversion of pollutants without substantial loss in catalytic activity. It was observed that these types of hydrogel systems can be used for the conversion of pollutants from waste water into useful products.

scholarly journals Novel Preparation of Noncovalent Modified GO Using RAFT Polymerization to Reinforce the Performance of Waterborne Epoxy Coatings

Coatings ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 348 ◽  
Author(s):  
Baolei Liu ◽  
Mingqian Wang ◽  
Ying Liang ◽  
Zhicheng Zhang ◽  
Guohong Ren ◽  
...  
Keyword(s):  
Raft Polymerization ◽  
Salt Spray ◽  
Thermo Gravimetric Analysis ◽  
Analytical Techniques ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
Block Polymer ◽  
Reversible Addition ◽  
Waterborne Epoxy ◽  
And Performance

This work launches the first-ever report on the fabrication of waterborne epoxy-graphene oxide (GO) coatings (WEGC) using a block polymer as a dispersant of GO, wherein the block polymer was synthesized via reversible addition-fragmentation chain transfer (RAFT) polymerization of acrylic acid and oligo(ethylene glycol) methyl ether methacrylate A number of analytical techniques, such as Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), X-ray diffraction (XRD), thermo gravimetric analysis (TGA), and salt spray tests, were utilized to explore the morphology and performance of the WEGC. It was confirmed that POEGMA950-b-PAA attached to the GO nanosheets, increasing the integral space of the sheets. Modified GO (MGO) layers were well-dispersed in the epoxy matrix through the formation of a GO-dispersant-epoxy ternary molecular structure. Furthermore, the presence of MGO substantially influenced the thermal properties, mechanical properties, and anticorrosion performance of the WEGC. TGA, salt spray tests, and pull-off testsshowed that 0.5 wt.% MGO content achieved the greatest improvement in the evaluated properties.

scholarly journals Enhanced Photocatalytic Activity of Cu2O Cabbage/RGO Nanocomposites under Visible Light Irradiation

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1712
Author(s):  
Appusamy Muthukrishnaraj ◽  
Salma Ahmed Al-Zahrani ◽  
Ahmed Al Otaibi ◽  
Semmedu Selvaraj Kalaivani ◽  
Ayyar Manikandan ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Thermo Gravimetric Analysis ◽  
Visible Region ◽  
Catalytic Performance ◽  
Precipitation Method ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Dye Pollutants ◽  
Transmission Electron

Towards the utilization of Cu2O nanomaterial for the degradation of industrial dye pollutants such as methylene blue and methyl orange, the graphene-incorporated Cu2O nanocomposites (GCC) were developed via a precipitation method. Using Hummers method, the grapheme oxide (GO) was initially synthesized. The varying weight percentages (1–4 wt %) of GO was incorporated along with the precipitation of Cu2O catalyst. Various characterization techniques such as Fourier-transform infra-red (FT-IR), X-ray diffraction (XRD), UV–visible diffused reflectance (UV-DRS), Raman spectroscopy, thermo gravimetric analysis (TGA), energy-dispersive X-ray analysis (EDX), and electro chemical impedance (EIS) were followed for characterization. The cabbage-like morphology of the developed Cu2O and its composites were ascertained from field-emission scanning electron microscopy (FESEM) and high-resolution transmission electron microscopy (HR-TEM). In addition, the growth mechanism was also proposed. The results infer that 2 wt % GO-incorporated Cu2O composites shows the highest value of degradation efficiency (97.9% and 96.1%) for MB and MO at 160 and 220 min, respectively. Further, its catalytic performance over visible region (red shift) was also enhanced to an appreciable extent, when compared with that of other samples.

Growth mechanism and characterization of ZnO nano-tubes synthesized using the hydrothermal-etching method

2009 ◽  
Vol 63 (6) ◽  
Author(s):  
Yan Li ◽  
Chuan-Sheng Liu ◽  
Yun-Ling Zou
Keyword(s):  
Room Temperature ◽  
Morphological Analysis ◽  
Diffraction Field ◽  
X Ray Diffraction ◽  
X Ray ◽  
Room Temperature Photoluminescence ◽  
Etching Method ◽  
Nano Rods ◽  
Two Stages

AbstractZnO nano-tubes (ZNTs) have been successfully synthesized via a simple hydrothermal-etching method, and characterized by X-ray diffraction, field emission scanning electron microscopy and room temperature photoluminescence measurement. The as-synthesized ZNTs have a diameter of 500 nm, wall thickness of 20–30 nm, and length of 5 µm. Intensity of the plane (0002) diffraction peak, compared with that of plane (10$$ \bar 1 $$0) of ZNTs, is obviously lower than that of ZnO nano-rods. This phenomenon can be caused by the smaller cross section of plane (0002) of the nano-tubes compared with that of other morphologies. On basis of the morphological analysis, the formation process of nano-tubes can be proposed in two stages: hydrothermal growth and reaction etching process.

Effect of Synthesis Temperature on Particles Size and Morphology of Zirconium Oxide Nanoparticle

2017 ◽  
Vol 50 ◽  
pp. 18-31 ◽  
Author(s):  
Rudzani Sigwadi ◽  
Simon Dhlamini ◽  
Touhami Mokrani ◽  
Patrick Nonjola
Keyword(s):  
Electron Microscopy ◽  
Particle Size ◽  
Zirconium Oxide ◽  
Thermo Gravimetric Analysis ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Crystallite Sizes ◽  
Ft Ir

The paper presents the synthesis and investigation of zirconium oxide (ZrO2) nanoparticles that were synthesised by precipitation method with the effects of the temperatures of reaction on the particles size, morphology, crystallite sizes and stability at high temperature. The reaction temperature effect on the particle size, morphology, crystallite sizes and stabilized a higher temperature (tetragonal and cubic) phases was studied. Thermal decomposition, band structure and functional groups were analyzed by Brunauer-Emmett-Teller (BET), Scanning Electron Microscopy (SEM), Transmission electron microscopy (TEM), X-ray diffraction (XRD), Thermo-gravimetric analysis (TGA) and Fourier transform infrared (FT-IR). The crystal structure was determined using X-ray diffraction. The morphology and the particle size were studied using (SEM) and (TEM). The shaped particles were confirmed through the SEM analysis. The transmission electron microscopic analysis confirmed the formation of the nanoparticles with the particle size. The FT-IR spectra showed the strong presence of ZrO2 nanoparticles.

Influence of Curing Temperature on Metakaolin-Based Geopolymers

2014 ◽  
Vol 775-776 ◽  
pp. 210-215
Author(s):  
Danúbia Lisbôa da Costa ◽  
Romualdo Rodrigues Menezes ◽  
Gelmires Araújo Neves ◽  
Sandro Marden Torres
Keyword(s):  
Room Temperature ◽  
Industrial Wastes ◽  
Curing Temperature ◽  
Inorganic Polymers ◽  
Flexural Test ◽  
X Ray Diffraction ◽  
Curing Conditions ◽  
X Ray ◽  
Natural Minerals ◽  
Application Potential

Geopolymers, also known as inorganic polymers, are aluminosilicates with cementing characteristics that have great application potential. They are produced by the alkaline activation of aluminosilicates precursors such as industrial wastes, calcined clays, natural minerals, among others and have their properties intimately associated to characteristics of the precursor materials and curing conditions. In this sense, this study aims to evaluate the mechanical behavior of geopolymers obtained from metakaolin according to the curing temperature. The geopolymerization was reached by the mixture of metakaolin with NaOH and the curing of the specimens was held at room temperature, 60°C and 100°C. The specimens were characterized by X-ray diffraction, mercury intrusion porosimetry, and SEM. The mechanical strength was determined by flexural test. The results show that the process of geopolymerization suffers a direct influence of the curing temperature used.

Investigations on Cu2+-substituted Ni–Zn ferrite nanoparticles

2016 ◽  
Vol 30 (32n33) ◽  
pp. 1650347
Author(s):  
Amarjeet ◽  
Vinod Kumar
Keyword(s):  
Spinel Phase ◽  
Thermo Gravimetric Analysis ◽  
Peak Position ◽  
Precipitation Method ◽  
Gravimetric Analysis ◽  
Frequency Range ◽  
X Ray Diffraction ◽  
Absorption Bands ◽  
X Ray ◽  
Zn Ferrite

[Formula: see text] ([Formula: see text] = 0.1, 0.3 and 0.5) nanoparticles were prepared by chemical co-precipitation method. The developed nanoparticles were characterized for structural properties by powder X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) techniques. Peak position in the X-ray diffraction pattern confirmed the single spinel phase of the developed particles. Infrared (IR) spectroscopy in mid-IR range showed the presence of characteristic absorption bands corresponding to octahedral and tetrahedral bonds in the spinel structure of prepared samples. Thermo-gravimetric analysis (TGA) measurements showed a considerable weight loss in the developed samples above 700[Formula: see text]C. Frequency dependence of the electrical properties of the developed material pellets was studied in the frequency range of 1 kHz–5 MHz. Temperature dependence of the dielectric constant of [Formula: see text] was studied at different temperatures, i.e. at 425, 450 and 475 K, in the frequency range of 1 kHz–5 MHz. It was found that the electrical conductivity decreases with increasing Cu[Formula: see text] ion content while it increases with the increase in temperature.

Comparing the Physico-Chemical Characteristics of Formulated and Marketed Yashada Bhasma

2021 ◽  
pp. 6392-6398
Author(s):  
Nitu Bhatnagar ◽  
Avani Pareek
Keyword(s):  
Inductively Coupled Plasma ◽  
Thermo Gravimetric Analysis ◽  
Human Consumption ◽  
Chemical Characteristics ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Inductively Coupled ◽  
Physico Chemical ◽  
The Difference

The present study is aimed to observe the difference in the Physico-Chemical characteristics of the marketed and formulated bhasma samples through X-Ray Diffraction analysis (XRD), Dynamic Light Scattering (DLS), Zeta potential, Thermo-Gravimetric analysis (TGA), Scanning Electron Microscopy (SEM) and Energy Dispersive X-Ray analysis (EDAX), apart from organoleptic methods. Inductively Coupled Plasma Mass Spectroscopy (ICPMS) analysis was also done to observe the presence of trace and heavy metals so that the safety of all these samples could be ensured. XRD shows variation in oxide nature of zinc as well crystallite size in all bhasma samples. DLS and SEM results show difference in particle size of marketed bhasma samples as compared to formulated Yashada bhasma. EDAX and ICPMS also confirm the alteration in elemental composition of all these bhasma samples. Thus, it can be concluded that these ayurvedic medicines should be prepared strictly using the formulation methods as mentioned in the Ayurvedic texts. This will help the prepared products to adopt the inherent quality of the ancient system of medicine, which shall be useful and devoid of any side effects for human consumption.

scholarly journals Synthesis of calcium-phosphate and chitosan bioceramics for bone regeneration

2001 ◽  
Vol 73 (4) ◽  
pp. 525-532 ◽  
Author(s):  
MELLATIE R. FINISIE ◽  
ATCHE JOSUÉ ◽  
VALFREDO T. FÁVERE ◽  
MAURO C. M. LARANJEIRA
Keyword(s):  
Bone Regeneration ◽  
Solid Phase ◽  
Thermo Gravimetric Analysis ◽  
Analytical Techniques ◽  
Bone Substitutes ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Beneficial Effects ◽  
Fourier Transformed Infrared Spectroscopy

Bioceramic composites were obtained from chitosan and hydroxyapatite pastes synthesized at physiological temperature according to two different syntheses approaches. Usual analytical techniques (X-ray diffraction analysis, Fourier transformed infrared spectroscopy, Thermo gravimetric analysis, Scanning electron microscopy, X-ray dispersive energy analysis and Porosimetry) were employed to characterize the resulting material. The aim of this investigation was to study the bioceramic properties of the pastes with non-decaying behavior from chitosan-hydroxyapatite composites. Chitosan, which also forms a water-insoluble gel in the presence of calcium ions, and has been reported to have pharmacologically beneficial effects on osteoconductivity, was added to the solid phase of the hydroxyapatite powder. The properties exhibited by the chitosan-hydroxyapatite composites were characteristic of bioceramics applied as bone substitutes. Hydroxyapatite contents ranging from 85 to 98% (w/w) resulted in suitable bioceramic composites for bone regeneration, since they showed a non-decaying behavior, good mechanical properties and suitable pore sizes.

Sign in / Sign up

Export Citation Format

Share Document