scholarly journals Effect of Silver Diamine Fluoride Pretreatment on Shear Bond Strength of Resin Modified Glass Ionomer Cement to Primary Dentin

2021 ◽  
Vol 9 (D) ◽  
pp. 243-247
Author(s):  
Maiada Mohammad Ahmad Sa’ada ◽  
Nagwa Mohammed Ali Khattab ◽  
Maha Ishaq Amer
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Testing Machine ◽  
Glass Ionomer Cement ◽  
In Vitro Study ◽  
Study Groups ◽  
Control Group ◽  
Glass Ionomer ◽  
Silver Diamine Fluoride

AIM: The aim of the study was to evaluate effect of silver diamine fluoride (SDF) on the shear bond strength (SBS) of glass ionomer restoration to primary dentine. MATERIALS AND METHODS: Twenty extracted primary molars with no restorations or developmental anomalies were only chosen for the study. Twenty dentine slices with 2 mm thickness were prepared and then randomly allocated into two groups (n = 10 per group). For Group 1 (experimental): Dentine surfaces were treated with 38% *SDF solution (Elevate oral care, USA) for 3 min using micro-brush, followed by a 30 s rinse with water and Group 2 (Control): Dentine surfaces were treated with distilled water for 3 min then rinsed for 30 s. The cavity conditioner was applied to flat dentin of both groups for 10 s then washed and dried gently with compressed air. All the specimens were restored with *RMGIC (Riva Light Cure, SDI, Australia). SBS was determined using a Universal Testing machine and Failure mode was evaluated using stereomicroscope. Data were collected and statistically analyzed. Independent t test was used to assess differences in SBS between study groups and mode of failure was analyzed using Fisher’s exact test. Level of significance was set at p ≤ 0.05. IBM SPSS statistical software (version 26) was used to analyze the data. RESULTS: The experimental group had significantly higher mean of shear bond (11.92 ± 3.35) strength than the control group (6.99 ± 2.98) (p = 0.003). CONCLUSIONS: Primary dentin pre-treatment with 38% SDF increases the shear bond strength between RMGIC and primary dentin according to the results of this in vitro study.

Comparative evaluation of shear bond strength of composite to dentin in presence of different dental liners: An in-vitro study

2021 ◽  
Author(s):  
Ladan Ranjbar Omrani ◽  
Saba Tohidkhah ◽  
Elham Ahmadi ◽  
Mahdi Abbasi ◽  
Reza Morvaridi Farimani
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Resin Composite ◽  
Testing Machine ◽  
Glass Ionomer Cement ◽  
In Vitro Study ◽  
Control Group ◽  
The One ◽  
Post Hoc

Abstract Background: The aim of the current study was to evaluate and compare the influence of Dycal, Lime-lite, Theracal LC, Biodentine, Resin-modified glass ionomer cement (RMGIC), and Activa Bioactive as the pulp capping material on the shear bond strength of resin composite to dentin.Methods: A total of 70 extracted caries-free molars were randomly assigned to seven groups. Six test groups were covered with various protective liners: Dycal (GD), Theracal LC (GT), lime-lite (GL), Activa Bioactive (GA), Biodentine (GB), RMGIC (GR). The control group (GC)received no liner pretreatment. Each sample was bonded to resin composite using the total-etch tetric N bond adhesive. The samples were then tested for shear bond strength using the universal testing machine at a cross-head speed of 1 mm/min until bond failure occurred. The data were analyzed using the one-way ANOVA test followed by the Tamhane post-hoc test for pairwise comparisons of the groupsResults: Independent of the type of the applied liner, all groups exhibited inferior SBS to dentine compared to the control group. GT and GR showed significantly higher shear bond strength than GB and GD, which showed the lowest shear bond strength. GL and GA also had significantly lower SBS results than GT. The mode of fracture was predominantly cohesive in GD, GB, and GT and adhesive in GA.Conclusion: This present study concludes that the bond strength of resin-composite to dentine can be affected differently using various types of liners.

Comparative Evaluation of Shear Bond Strength of Composite to Dentin in Presence of Calcium Releasing Liners: An In-Vitro Study

2021 ◽  
Author(s):  
Saba Tohidkhah ◽  
Elham Ahmadi ◽  
Mahdi Abbasi ◽  
Reza Morvaridi Farimani ◽  
Ladan Ranjbar Omrani
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Resin Composite ◽  
Testing Machine ◽  
Glass Ionomer Cement ◽  
In Vitro Study ◽  
Control Group ◽  
The One ◽  
Post Hoc

Abstract Background: The aim of current study was to evaluate and compare the influence of Dycal, Lime-lite, Theracal LC, Biodentine, Resin-modified glass ionomer cement (RMGIC), and Activa Bioactive as the pulp capping material on the shear bond strength of resin composite to dentin.Methods: A total of 70 extracted caries-free molars were randomly assigned to seven groups. Six test groups were covered with various protective liners: Dycal (GD), Theracal LC (GT), lime-lite (GL), Activa Bioactive (GA), Biodentine (GB), RMGIC (GR). The control group (GC)received no liner pretreatment. Each sample was bonded to resin composite using the total-etch tetric N bond adhesive. The samples were then tested for shear bond strength using the universal testing machine at a cross-head speed of 1 mm/min until bond failure occurred. The data were analyzed using the one-way ANOVA test followed by the Tamhane post-hoc test for pairwise comparisons of the groupsResults: Independent of the type of the applied liner, all groups exhibited inferior SBS to dentine compared to the control group. GT and GR showed significantly higher shear bond strength than GB and GD, which showed the lowest shear bond strength. GL and GA also had significantly lower SBS results than GT. The mode of fracture was predominantly cohesive in GD, GB, and GT and adhesive in GA.Conclusion: This present study concludes that the bond strength of resin-composite to dentine can be affected differently using various types of liners.

Comparative evaluation of shear bond strength of composite to dentin in presence of different dantal liners: An in-vitro study

2021 ◽  
Author(s):  
Ladan Ranjbar Omrani ◽  
Saba Tohidkhah ◽  
Elham Ahmadi ◽  
Mahdi Abbasi ◽  
Reza Morvaridi Farimani
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Resin Composite ◽  
Testing Machine ◽  
Glass Ionomer Cement ◽  
In Vitro Study ◽  
Control Group ◽  
The One ◽  
Post Hoc

Abstract Background: The aim of the current study was to evaluate and compare the influence of Dycal, Lime-lite, Theracal LC, Biodentine, Resin-modified glass ionomer cement (RMGIC), and Activa Bioactive as the pulp capping material on the shear bond strength of resin composite to dentin.Methods: A total of 70 extracted caries-free molars were randomly assigned to seven groups. Six test groups were covered with various protective liners: Dycal (GD), Theracal LC (GT), lime-lite (GL), Activa Bioactive (GA), Biodentine (GB), RMGIC (GR). The control group (GC)received no liner pretreatment. Each sample was bonded to resin composite using the total-etch tetric N bond adhesive. The samples were then tested for shear bond strength using the universal testing machine at a cross-head speed of 1 mm/min until bond failure occurred. The data were analyzed using the one-way ANOVA test followed by the Tamhane post-hoc test for pairwise comparisons of the groupsResults: Independent of the type of the applied liner, all groups exhibited inferior SBS to dentine compared to the control group. GT and GR showed significantly higher shear bond strength than GB and GD, which showed the lowest shear bond strength. GL and GA also had significantly lower SBS results than GT. The mode of fracture was predominantly cohesive in GD, GB, and GT and adhesive in GA.Conclusion: This present study concludes that the bond strength of resin-composite to dentine can be affected differently using various types of liners.

scholarly journals Shear Bond Strength of Three Orthodontic Bonding Systems on Enamel and Restorative Materials

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Andreas Hellak ◽  
Jennifer Ebeling ◽  
Michael Schauseil ◽  
Steffen Stein ◽  
Matthias Roggendorf ◽  
...  
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Testing Machine ◽  
In Vitro Study ◽  
Control Group ◽  
Metal Composite ◽  
Universal Adhesive ◽  
Restorative Materials ◽  
Bonding Systems

Objective.The aim of this in vitro study was to determine the shear bond strength (SBS) and adhesive remnant index (ARI) score of two self-etching no-mix adhesives (iBond™and Scotchbond™) on different prosthetic surfaces and enamel, in comparison with the commonly used total etch system Transbond XT™.Materials and Methods. A total of 270 surfaces (1 enamel and 8 restorative surfaces,n=30) were randomly divided into three adhesive groups. In group 1 (control) brackets were bonded with Transbond XT primer. In the experimental groups iBond adhesive (group 2) and Scotchbond Universal adhesive (group 3) were used. The SBS was measured using a Zwicki 1120™testing machine. The ARI and SBS were compared statistically using the Kruskal–Wallis test (P≤0.05).Results. Significant differences in SBS and ARI were found between the control group and experimental groups.Conclusions. Transbond XT showed the highest SBS on human enamel. Scotchbond Universal on average provides the best bonding on all other types of surface (metal, composite, and porcelain), with no need for additional primers. It might therefore be helpful for simplifying bonding in orthodontic procedures on restorative materials in patients. If metal brackets have to be bonded to a metal surface, the use of a dual-curing resin is recommended.

Does Addition of Propolis to Glass Ionomer Cement Alter its Physicomechanical Properties? An in Vitro Study

2016 ◽  
Vol 40 (5) ◽  
pp. 400-403 ◽  
Author(s):  
P Subramaniam ◽  
KL Girish Babu ◽  
G Neeraja ◽  
S Pillai
Keyword(s):  
Compressive Strength ◽  
Testing Machine ◽  
Glass Ionomer Cement ◽  
In Vitro Study ◽  
Physicomechanical Properties ◽  
Control Group ◽  
Glass Ionomer ◽  
Experimental Group ◽  
Ionomer Cement

Propolis is a natural resinous substance produced by honey bees. The antimicrobial effects of glass ionomer cement have been shown to improve with the addition of propolis; however its effect on the physicomechanical properties of the cement is not known. Aim: The purpose of this study was to evaluate the compressive strength and solubility of conventional restorative glass ionomer cement following the addition of propolis. Study design: Twenty half cylindrical samples were prepared with conventional restorative glass ionomer cement formed the control group. Another twenty samples were prepared with propolis added to conventional restorative glass ionomer cement formed the experimental group. The compressive strength was assessed using universal testing machine. To assess solubility, the samples were immersed in deionised water at room temperature, for 7 days. The solubility was measured as a difference in the weight of the sample; prior to immersion and following immersion at the end of each day. Results: The control group had a significantly higher mean compressive strength of 146.26 Mpa as compared to the experimental group (135.06 Mpa). The solubility between the groups was significant. Conclusion: In comparison to the control group, incorporation of propolis to conventional restorative glass ionomer cement decreased the compressive strength significantly. The solubility of the cement in the experimental group increased significantly over 7day period as compared to the control group.

scholarly journals Effect of Contamination with Hemostatic Agent on Shear Bond Strength of Composite to Dentin Using G-Premio and Single Bond Universal Adhesives

2021 ◽  
Author(s):  
Zahra Khamverdi ◽  
Naemeh Karimian ◽  
Maryam Farhadian ◽  
Hamed Gheitouli
Keyword(s):  
Bond Strength ◽  
Shear Bond Strength ◽  
Testing Machine ◽  
In Vitro Study ◽  
Hemostatic Agent ◽  
Control Group ◽  
Single Bond ◽  
Failure Data ◽  
Universal Adhesives

Objectives: Bond strength of composite restorations plays an important role in their success. This in vitro study evaluated the effect of a hemostatic agent on shear bond strength of universal adhesives. Materials and Methods: Thirty-six extracted human molars were used in this study. Buccal and lingual surfaces were reduced to obtain flat dentin surfaces and were ground with a silicone paper. The samples were randomly divided into three groups (n=12) based on the application of hemostatic agent: group 1: no contamination (control), group 2: aluminum chloride application, and group 3: ferric sulfate application. Each group was then divided into two subgroups (n=6) for using G-Premio and Single Bond Universal. Resin cylinders (Filtek Z550) were bonded to dentin surfaces according to the manufacturer’s instructions. After 1000 thermal cycles, shear load was applied to the specimens using a universal testing machine at a crosshead speed of 1 mm/min until failure. Data were statistically analyzed using two-way ANOVA and Tukey’s post-hoc test (α=0.05). Results: There were statistically significant differences in shear bond strength of the three main groups for both G-Premio and Single Bond Universal (P<0.05). When the adhesive systems were compared with each other, G-Premio showed higher shear bond strength than Single Bond Universal (P<0.05). Conclusion: Contamination with hemostatic agents had an adverse effect on the shear bond strength of universal adhesives. Moreover, G-Premio yielded a higher bond strength than Single Bond Universal.

Sign in / Sign up

Export Citation Format

Share Document