Effect of Process Parameters on Depth of Penetration & Surface Roughness in Abrasive Waterjet Cutting of Copper

2019 ◽  
Vol 895 ◽  
pp. 301-306
Author(s):  
Keshav Kashyap ◽  
S. Srinivas
Keyword(s):  
Surface Roughness ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Process Parameters ◽  
Flow Rate ◽  
Traverse Speed ◽  
High Water ◽  
Water Jet ◽  
Abrasive Waterjet ◽  
Depth Of Penetration

This study evaluates the effect of process parameters on depth of penetration and surface roughness in abrasive waterjet (AWJ) cutting of copper. Full factorial experiments are carried out on trapezoidal blocks for each of the three abrasive particle sizes used. Experimental parameters - abrasive mass flow rate, water jet pressure and traverse speed are varied at three levels. Main effects and contributions of process parameters to depth of penetration and surface roughness is calculated. From the data, it is observed that, high abrasive mass flow rate, high water jet pressure and low traverse speed resulted in higher depth of penetration and a high abrasive mass flow rate, high water jet pressure and low traverse speed resulted in lesser Ra value. Using experimental data a statistical model for predicting depth of penetration & surface roughness is developed. Error between experimental and statistical values are compared to validate the statistical model. The maximum DOP of 49.32mm was observed at AMFR=405.4 g/min, P=300 MPa, TS=60 mm/min, MS=60 Mesh and minimum DOP of 4.27mm was observed at AMFR=200 g/min, P=100 MPa, TS=90 mm/min, MS=80 Mesh.

scholarly journals Analysis and Optimization of Process Parameters in Abrasive Waterjet Contour Cutting of AISI 304L

Metals ◽  
2021 ◽  
Vol 11 (9) ◽  
pp. 1362
Author(s):  
Jennifer Milaor Llanto ◽  
Ana Vafadar ◽  
Muhammad Aamir ◽  
Majid Tolouei-Rad
Keyword(s):  
Surface Roughness ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Process Parameters ◽  
Flow Rate ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Traverse Speed ◽  
Abrasive Waterjet

Abrasive waterjet machining is applied in various industries for contour cutting of heat-sensitive and difficult-to-cut materials like austenitic stainless steel 304L, with the goal of ensuring high surface integrity and efficiency. In alignment with this manufacturing aspiration, experimental analysis and optimization were carried out on abrasive waterjet machining of austenitic stainless steel 304L with the objectives of minimizing surface roughness and maximizing material removal rate. In this machining process, process parameters are critical factors influencing contour cutting performance. Accordingly, Taguchi’s S/N ratio method has been used in this study for the optimization of process parameters. Further in this work, the impacts of input parameters are investigated, including waterjet pressure, abrasive mass flow rate, traverse speed and material thickness on material removal rate and surface roughness. The study reveals that an increasing level of waterjet pressure and abrasive mass flow rate achieved better surface integrity and higher material removal values. The average S/N ratio results indicate an optimum value of waterjet pressure at 300 MPa and abrasive mass flow rate of 500 g/min achieved minimum surface roughness and maximum material removal rate. It was also found that an optimized value of a traverse speed at 90 mm/min generates the lowest surface roughness and 150 mm/min produces the highest rate of material removed. Moreover, analysis of variance in the study showed that material thickness was the most influencing parameter on surface roughness and material removal rate, with a percentage contribution ranging 90.72–97.74% and 65.55–78.17%, respectively.

Surface Waviness in Abrasive Waterjet Offset-Mode Turning

2014 ◽  
Vol 599-601 ◽  
pp. 555-559
Author(s):  
Iman Zohourkari ◽  
Mehdi Zohoor ◽  
Massimiliano Annoni
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Rotational Speed ◽  
Water Pressure ◽  
Traverse Speed ◽  
Abrasive Waterjet ◽  
Depth Of Cut ◽  
Surface Waviness ◽  
Cutting Head

In this paper, surface waviness quality in abrasive waterjet offset-mode turning has been studied regarding variations of some process parameters. Influence of five main operational parameters such as water pressure, cutting head traverse speed, abrasive mass flow rate, workpiece rotational speed and depth of cut on surface waviness of turned parts have been investigated using statistical approach. Second order regression model presented for surface waviness. The model accuracy was verified by comparing with experimental data. It found that abrasive mass flow rate, cutting head traverse speed and DOC are the most influential parameters while water pressure and workpiece rotational speed show lesser effectiveness.

Investigations on surface roughness and tribology of miniature brass gears manufactured by abrasive water jet machining

2017 ◽  
Vol 232 (22) ◽  
pp. 4193-4202 ◽  
Author(s):  
Thobi Phokane ◽  
Kapil Gupta ◽  
Munish Kumar Gupta
Keyword(s):  
Surface Roughness ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Optimization Technique ◽  
Water Jet ◽  
Machining Parameters ◽  
Abrasive Water Jet ◽  
Abrasive Water Jet Machining ◽  
Particle Swarm Optimization Technique

Surface roughness parameters are important indicators for determining the operating performance, tribology behavior, wear and tear characteristics, and service life of engineered parts including gears. This article presents the investigation on surface roughness, and tribology and wear aspects of miniature brass gears manufactured by abrasive water jet machining. Experiments have been conducted based on Taguchi's robust design technique with L9 orthogonal array to machine external spur-type miniature gears of brass having 8.4 mm pitch diameter, 12 teeth, and 5 mm thickness. The effect of three important process parameters namely water jet pressure, abrasive mass flow rate, and stand-off distance on mean roughness depth of miniature gears are analyzed. Surface roughness is found to decrease with the increase in the water jet pressure and abrasive mass flow rate, and increases with the increase in the stand-off distance. Particle swarm optimization technique has been used for parametric optimization to minimize the surface roughness of miniature gears. Confirmation experiment conducted at optimized abrasive water jet machining parameters resulted in superfine surface finish with mean roughness depth value of 4.1 µm superior than the finish obtained by other advanced processes for brass gears. The investigated values of bearing area characteristics, skewness, kurtosis, and friction coefficient confirm the tribological fitness of the miniature brass gear machined at optimum abrasive water jet machining parameters.

Modeling of Surface Waviness in Abrasive Waterjet Offset-Mode Turning

2014 ◽  
Vol 621 ◽  
pp. 202-207
Author(s):  
Iman Zohourkari ◽  
Mehdi Zohoor ◽  
Massimiliano Annoni
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Rotational Speed ◽  
Water Pressure ◽  
Traverse Speed ◽  
Abrasive Waterjet ◽  
Depth Of Cut ◽  
Surface Waviness ◽  
Cutting Head

In this paper, surface waviness produced by turning aluminum parts with abrasive waterjet has been studied regarding changes in some process parameters. Effect of five major parameters such as water pressure, cutting head traverse speed, abrasive mass flow rate, workpiece rotational speed and depth of cut have been investigated using analysis of variances. Second order regression model presented forwaviness.The validity of the model wasconfirmed bycomparing with experimental data. It found thatabrasive mass flow rate, cutting head traverse speed and DOC are the most influencing parameters while water pressure and workpiece rotational speed show lesser effectiveness.

scholarly journals Water Jet Automation

2021 ◽  
Vol 11 (10) ◽  
pp. 177-181
Author(s):  
Michael Paszczuk ◽  
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Human Error ◽  
Traverse Speed ◽  
Water Jet ◽  
Optimization Techniques ◽  
Tolerance Zone ◽  
Helpful Tool ◽  
Water Jet Cutting

Water jet cutting has been an extremely helpful tool that creates flawless parts with tolerances up to 0.1 mm. During the cutting process, it is important to note that each step must be optimized to create the best finish or maintain the correct tolerance zone. These steps are composed of abrasive mass flow rate, traverse speed, and standoff distance. In order for these optimization techniques to be followed a strict set of rules must be followed to ensure consistent progression. Programs such as MATLAB can be utilized to reduce human error in the calculations. MATLAB files can then be saved to use with other materials and thickness combinations.

Experimental study of delamination and kerf geometry of carbon epoxy composite machined by abrasive water jet

2017 ◽  
Vol 51 (24) ◽  
pp. 3373-3390 ◽  
Author(s):  
Ajit Dhanawade ◽  
Shailendra Kumar
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Process Parameters ◽  
Flow Rate ◽  
Epoxy Composite ◽  
Water Jet ◽  
Hydraulic Pressure ◽  
Abrasive Water Jet ◽  
Abrasive Water Jet Machining ◽  
Kerf Taper

The present article focuses on mechanism of delamination and kerf geometry in abrasive water jet machining of carbon epoxy composite. In the present study, four process parameters of abrasive water jet machining namely hydraulic pressure, traverse rate, stand-off distance, and abrasive mass flow rate are considered. The experiments are performed on the basis of response surface methodology as a statistical design of experiment approach. Delamination in machined samples is observed by using scanning electron microscope. Analysis of variance is performed in order to investigate the influence of process parameters on delamination, kerf taper ratio, and kerf top width. It is found that delamination decreases with increase in pressure and abrasive mass flow rate and decrease in stand-off distance and traverse rate. Kerf taper ratio decreases with increase in pressure and decrease in traverse rate and stand-off distance. Kerf top width decreases with decrease in stand-off distance and increase in traverse rate. Based on analysis, mathematical models are developed to predict the maximum delamination length, kerf taper ratio, and kerf top width. Further, a multi-response optimization is performed on the basis of desirability function to minimize delamination, kerf taper ratio, and kerf top width.

scholarly journals Centrifugal Compressor Stall Control by the Application of Engineered Surface Roughness on Diffuser Shroud Using Numerical Simulations

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2033
Author(s):  
Amjid Khan ◽  
Muhammad Irfan ◽  
Usama Muhammad Niazi ◽  
Imran Shah ◽  
Stanislaw Legutko ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Centrifugal Compressor ◽  
Control Method ◽  
Flow Instability ◽  
Passive Flow Control ◽  
Passive Flow ◽  
Low Mass

Downsizing in engine size is pushing the automotive industry to operate compressors at low mass flow rate. However, the operation of turbocharger centrifugal compressor at low mass flow rate leads to fluid flow instabilities such as stall. To reduce flow instability, surface roughness is employed as a passive flow control method. This paper evaluates the effect of surface roughness on a turbocharger centrifugal compressor performance. A realistic validation of SRV2-O compressor stage designed and developed by German Aerospace Center (DLR) is achieved from comparison with the experimental data. In the first part, numerical simulations have been performed from stall to choke to study the overall performance variation at design conditions: 2.55 kg/s mass flow rate and rotational speed of 50,000 rpm. In second part, surface roughness of magnitude range 0–200 μm has been applied on the diffuser shroud to control flow instability. It was found that completely rough regime showed effective quantitative results in controlling stall phenomena, which results in increases of operating range from 16% to 18% and stall margin from 5.62% to 7.98%. Surface roughness as a passive flow control method to reduce flow instability in the diffuser section is the novelty of this research. Keeping in view the effects of surface roughness, it will help the turbocharger manufacturers to reduce the flow instabilities in the compressor with ease and improve the overall performance.

EXPERIMENTAL STUDY OF SURFACE ROUGHNESS AND TAPER ANGLE IN ABRASIVE WATER JET MACHINING OF 7075 ALUMINUM COMPOSITE USING RESPONSE SURFACE METHODOLOGY

2019 ◽  
Vol 27 (03) ◽  
pp. 1950112 ◽  
Author(s):  
A. SHANMUGAM ◽  
K. KRISHNAMURTHY ◽  
T. MOHANRAJ
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Process Parameters ◽  
Water Pressure ◽  
Traverse Speed ◽  
Standoff Distance ◽  
Abrasive Waterjet ◽  
Machined Surface ◽  
Taper Angle

Surface roughness and taper angle of an abrasive waterjet machined surface of 7075 Aluminum metal matrix composite were deliberately studied. Response surface methodology design of experiments and analysis of variance were used to design the experiments and to identify the effect of process parameters on surface roughness and taper angle. The jet traverse speed and jet pressure were the most significant process parameters which influence the surface roughness and taper angle, respectively. Increasing the pressure and jet traverse speed results in increasing the surface roughness and taper angle. At the same time, decreasing the standoff distance and jet traverse speed possibly enhances both the responses. The optimal process parameters of 1[Formula: see text]mm as standoff distance, 192[Formula: see text]MPa as water pressure and 30[Formula: see text]mm[Formula: see text]min[Formula: see text] as jet traverse speed were identified to obtain the minimum value of surface roughness and taper angle. Based on the optimal parameters, the confirmation test was conducted. The mathematical equation was obtained from the experimental data using regression analysis; it was observed that the error was less than 5% of the experimentally measured values.

Sign in / Sign up

Export Citation Format

Share Document