Effect of Grain Size on Microstructure and Aging Behavior in AM60 Magnesium Alloy

2011 ◽  
Vol 409 ◽  
pp. 373-378
Author(s):  
H. Takano ◽  
Mitsuaki Furui ◽  
Susumu Ikeno ◽  
Tomoyasu Yamaguchi ◽  
Seiji Saikawa
Keyword(s):  
Grain Size ◽  
Magnesium Alloy ◽  
Grain Boundary ◽  
Eutectic Reaction ◽  
Age Hardening ◽  
Peak Hardness ◽  
Aging Behavior ◽  
Continuous Precipitation ◽  
Hardening Behavior ◽  
Average Grain Size

Our recent studies showed that continuous and cellular precipitates are covered with the whole of crystal grain in age hardable AM60 magnesium alloy cast into permanent molds, which have the average grain size of 75-85μm. Also, continuous precipitation is generated nearby grain boundary in the same alloys cast into sand molds, which have the average grain size of 138-147μm. It’s thought that permanent mold castings have the age hardening behavior of intragranular precipitation participation type that is influenced by continuous precipitates. It’s also thought that sand mold castings have the age hardening behavior of grain boundary participation type that is influenced by cellular precipitates. In this study, AM60 magnesium alloy with larger grain size was used to detect the grain size dependence of microstructure and aging behavior. In the microstructure of as-cast condition, the larger the grain size, it was shown that the none-equilibrium crystallized β phase with eutectic reaction during the solidification between liquidus and solidus temperatures becomes large-size. In the age hardening curves, the peak hardness values become higher with decreasing of grain size.

Age-Hardening Behavior of Mg-Al-Zn Alloys Produced by Sand Mold Casting

2014 ◽  
Vol 783-786 ◽  
pp. 467-471
Author(s):  
Seiji Saikawa ◽  
Yuhei Ebata ◽  
Kiyoshi Terayama ◽  
Susumu Ikeno ◽  
Emi Yanagihara
Keyword(s):  
Magnesium Alloy ◽  
Aging Temperature ◽  
Volume Fraction ◽  
Discontinuous Precipitation ◽  
Sand Mold ◽  
Age Hardening ◽  
Aged Sample ◽  
Maximum Hardness ◽  
Continuous Precipitation ◽  
Hardening Behavior

In recent years, Mg-Al-Zn system alloy has been used for the parts in the automobile for weight reductions. The age-hardening behavior of Mg-6mass%Al (-1mass%Zn)-0.3mass%Mn alloys sand mold castings were investigated by Vickers hardness measurement and optical microscopic observation. Both alloys were solution-treated and then isothermal-aged at 473, 498 and 523K. For each aging temperature, both alloys were indicated age-hardening obviously, and decreased the value of maximum hardness and shorten time to maximum hardness with heighten aging temperature. Age-hardening curves for both alloys approximately showed the same change of hardness. However, these optical micrographs after aging treatment are observed different microstructure. In case of AM60 magnesium alloy, discontinuous precipitation preferentially occurred in aged sample. The volume fraction of discontinuous precipitation was larger than that of continuous precipitation. On the other hand, in case of AZ61 magnesium alloy, the volume fraction of continuous precipitation was larger than that of discontinuous precipitation. Furthermore, over-aged sample of both alloys were consisted of discontinuous precipitation, continuous precipitation and pre-precipitation area.

Effect of 1% Ce Addition on Microstructures and Mechanical Properties of As-Cast Mg-3.8Zn-2.2Ca (wt.%) Magnesium Alloy

2011 ◽  
Vol 686 ◽  
pp. 80-83
Author(s):  
Ming Bo Yang ◽  
Cai Yuan Qin ◽  
Yi Zhu ◽  
Liang Cheng
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Magnesium Alloy ◽  
Fine Particles ◽  
Age Hardening ◽  
Creep Properties ◽  
Microstructure And Mechanical Properties ◽  
Average Grain Size ◽  
Microstructures And Mechanical Properties ◽  
Cast Microstructure

In this paper, the effect of adding 1.0 wt.% Ce on the as-cast microstructure and mechanical properties of the Mg-3.8Zn-2.2Ca (wt.%) magnesium alloy were investigated. The results indicate that, after adding 1.0 wt.%Ce to the Mg-3.8Zn-2.2Ca alloy, small amounts of Mg12Ce phase are formed and an obvious equiaxed trendance is observed. At the same time, the average grain size decreases from 234mm to 71mm and the morphology of some Ca2Mg6Zn3phases changes from initial coarse blocks to fine particles. In addition, adding 1.0 wt.%Ce to the Mg-3.8Zn-2.2Ca alloy also improve the tensile and creep properties of the alloy. Further investigations need to be considered in order to optimize the amounts of Ce additions and understand its effects on the tensile and creep properties and age-hardening behaviour.

scholarly journals Dislocations in Grain Boundary Regions: The Origin of Heterogeneous Microstrains in Nanocrystalline Materials

2019 ◽  
Vol 51 (1) ◽  
pp. 513-530 ◽  
Author(s):  
Zhenbo Zhang ◽  
Éva Ódor ◽  
Diana Farkas ◽  
Bertalan Jóni ◽  
Gábor Ribárik ◽  
...  
Keyword(s):  
Grain Size ◽  
Grain Boundary ◽  
Nanocrystalline Materials ◽  
Md Simulation ◽  
High Pressure Torsion ◽  
Md Simulations ◽  
Line Profile Analysis ◽  
Misfit Dislocations ◽  
X Ray ◽  
Average Grain Size

Abstract Nanocrystalline materials reveal excellent mechanical properties but the mechanism by which they deform is still debated. X-ray line broadening indicates the presence of large heterogeneous strains even when the average grain size is smaller than 10 nm. Although the primary sources of heterogeneous strains are dislocations, their direct observation in nanocrystalline materials is challenging. In order to identify the source of heterogeneous strains in nanocrystalline materials, we prepared Pd-10 pct Au specimens by inert gas condensation and applied high-pressure torsion (HPT) up to γ ≅ 21. High-resolution transmission electron microscopy (HRTEM) and molecular dynamic (MD) simulations are used to investigate the dislocation structure in the grain interiors and in the grain boundary (GB) regions in the as-prepared and HPT-deformed specimens. Our results show that most of the GBs contain lattice dislocations with high densities. The average dislocation densities determined by HRTEM and MD simulation are in good correlation with the values provided by X-ray line profile analysis. Strain distribution determined by MD simulation is shown to follow the Krivoglaz–Wilkens strain function of dislocations. Experiments, MD simulations, and theoretical analysis all prove that the sources of strain broadening in X-ray diffraction of nanocrystalline materials are lattice dislocations in the GB region. The results are discussed in terms of misfit dislocations emanating in the GB regions reducing elastic strain compatibility. The results provide fundamental new insight for understanding the role of GBs in plastic deformation in both nanograin and coarse grain materials of any grain size.

Effects of Specimen Diameter on Microstructure and Microhardness of Hot Extruded AZ31B Magnesium Alloy

2014 ◽  
Vol 1004-1005 ◽  
pp. 158-162 ◽  
Author(s):  
Xiang Ting Hong ◽  
Fu Chen ◽  
Fei Chen ◽  
Wang Yu ◽  
Bo Rong Sang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Magnesium Alloy ◽  
Size Effects ◽  
Strain Distribution ◽  
Elevated Temperatures ◽  
Az31b Magnesium Alloy ◽  
Specimen Diameter ◽  
Average Grain Size ◽  
Micro Parts

Microstructures of metal micro parts after microforming at elevated temperatures must be evaluated due to mechanical properties depend on average grain size. In this work, the effects of specimen diameter on the microstructure and microhardness of a hot-extruded AZ31B magnesium alloy were studied. Obvious size effect on microstructure and microhardness of the alloy could be observed. The size effects could be explained by strain distribution and dislocation density differences between the two kinds of specimens.

Influence of Annealing on the Microstructure and Mechanical Properties of Electrodeposited Nanocrystalline Nickel

2011 ◽  
Vol 683 ◽  
pp. 103-112 ◽  
Author(s):  
B. Yang
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Elastic Modulus ◽  
Grain Boundary ◽  
Boundary Structure ◽  
Boundary State ◽  
Microstructure And Mechanical Properties ◽  
Grain Boundary Structure ◽  
Average Grain Size ◽  
Different Grain Size

The evolution of the microstructure and mechanical properties of electrodeposited nanocrystalline Ni with different annealing procedures was studied systematically. For the annealed specimens hardness decreases with increasing average grain size but the dependence changes at different grain size ranges. The specimens annealed at a low temperature show higher hardness compared to the as-deposited nanocrystalline Ni, despite an increased measured average grain size. In association with this hardening an increase in elastic modulus and a decrease in microstrain was observed after annealing. With increasing annealing temperature both the tensile strength and the fracture strain were observed to decrease, this is companied with a transition from ductile to brittle in the fracture surfaces. These results indicated that the mechanical behaviour of nanocrystalline Ni depends not only on the average grain size but also on the grain boundary structure. A change in the grain boundary state arising from annealing may be responsible for the observed increase in hardness and elastic modulus as well as the deterioration of tensile properties.

Microstructure Prediction by Finite Element Analysis during Hot Rolling of Magnesium Alloy Sheets

2015 ◽  
Vol 661 ◽  
pp. 105-112
Author(s):  
Yeong Maw Hwang ◽  
Tso Lun Yeh
Keyword(s):  
Grain Size ◽  
Magnesium Alloy ◽  
Optimal Conditions ◽  
Compression Tests ◽  
Element Analysis ◽  
Grain Sizes ◽  
Average Grain Size ◽  
Microstructure Prediction ◽  
Alloy Microstructure ◽  
The Relationship

Material’s plastic deformation by hot forming processes can be used to make the materials generate dynamic recrystallization (DRX) and fine grains and accordingly products with more excellent mechanical properties, such as higher strength and larger elongation can be obtained. In this study, compression tests and water quenching are conducted to obtain the flow stress of the materials and the grain size after DRX. Through the regression analysis, prediction equations for the magnesium alloy microstructure were established. Simulations with different rolling parameters are conducted to find out the relationship between the DRX fractions or grain sizes of the rolled products and the rolling parameters. The simulation results show that rolling temperature of 400°C and thickness reduction of 50% are the optimal conditions. An average grain size of 0.204μm-0.206μm in the microstructure is obtained and the strength and formability of ZK60 magnesium alloys can be improved.

Effect of CO2 Laser Surface Melting on the Microstructure of AZ91D Magnesium Alloy

2011 ◽  
Vol 464 ◽  
pp. 461-464
Author(s):  
Ju Fang Chen ◽  
Xing Cheng Li ◽  
Jiang Tao Wang ◽  
Wei Ning Lei
Keyword(s):  
Grain Size ◽  
Magnesium Alloy ◽  
Continuous Wave ◽  
Surface Melting ◽  
Laser Surface ◽  
Laser Surface Melting ◽  
Micro Hardness ◽  
Az91d Magnesium Alloy ◽  
Average Grain Size ◽  
Melted Layer

In the present study, the effect of laser surface melting (LSM) on microstructure of AZ91D magnesium alloy was investigated with a 2kW continuous wave CO2 laser. The results indicate that both the substrate and laser melted layer mainly consisted of α-Mg and β-Mg17Al12, the amount of β-phase in laser melted layer was decreased as compared to that of the substrate. The microstructure of the laser surface melted zone consists of fine dendrites with an average grain size of less than 10m, the grain size was reduced by a factor of more than 10 times as compared to that of the substrate. The micro-hardness of the melted layer was increased to 70–85HV as compared to that of the substrate (about 53HV). Because of the grain refinement, the enhancement of the hard phase β-Mg17Al12, and the solid solution hardening of alloy elements, the micro-hardness and strength of the laser melted layer was increased significantly.

Characterization of Zinalco Alloy Superplastically Deformed Using Orientation Imaging Microscopy

2009 ◽  
Vol 1242 ◽  
Author(s):  
Ramos A. Mitsuo ◽  
Martínez F. Elizabeth ◽  
Negrete S. Jesús ◽  
Torres-Villaseñor G.
Keyword(s):  
Grain Size ◽  
Grain Boundary ◽  
Grain Boundaries ◽  
Superplastic Deformation ◽  
Orientation Imaging Microscopy ◽  
Grain Boundary Sliding ◽  
Boundary Misorientation ◽  
Average Grain Size ◽  
Grain Boundary Misorientation ◽  
Misorientation Angles

ABSTRACTZinalco alloy (Zn-21mass%Al-2mass%Cu) specimens were deformed superplastically with a strain rate (ε) of 1×10-3 s-1 at homologous temperature (TH) of 0.68 (5 ). It was observed neck formation that indicate nonhomegeneus deformation. Grain size and grain boundaries misorientation changes, due superplastic deformation, were characterized by Orientation Imagining Microscopy (OIM) technique. It was studied three regions in deformed specimens and the results were compared with the results for a specimen without deformation. Average grain size of 1 mm was observed in non-deformed specimen and a fraction of 82% for grain boundary misorientation angles with a grain boundaries angles between 15° and 55° was found. For deformed specimen, the fraction of angles between 15° and 55° was decreced to average value of 75% and fractions of low angle (<5°) and high angle (>55°) misorientations were 10% and 15% respectively. The grain size and high fraction of grain boundary misorientation angles between 15° and 55° observed in the alloy without deformation, are favorable for grain rotation and grain boundary sliding (GBS) procces. The changes observed in the fraction of favorable grain boundary angles during superplastic deformation, shown that the superplastic capacity of Zinalco was reduced with the deformation.

The Effect of Grain Size on the Strain Hardening Behavior for Extruded ZK61 Magnesium Alloy

2017 ◽  
Vol 26 (12) ◽  
pp. 6013-6021 ◽  
Author(s):  
Lixin Zhang ◽  
Wencong Zhang ◽  
Wenzhen Chen ◽  
Junpeng Duan ◽  
Wenke Wang ◽  
...  
Keyword(s):  
Grain Size ◽  
Magnesium Alloy ◽  
Strain Hardening ◽  
Hardening Behavior ◽  
Strain Hardening Behavior

Effect of Bi on Microstructure and Mechanical Properties of Extruded AZ80-2Sn Magnesium Alloy

2018 ◽  
Vol 37 (1) ◽  
pp. 97-103 ◽  
Author(s):  
Hansong Xue ◽  
Xinyu Li ◽  
Weina Zhang ◽  
Zhihui Xing ◽  
Jinsong Rao ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Magnesium Alloy ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Microstructure And Mechanical Properties ◽  
Average Grain Size

AbstractThe effects of Bi on the microstructure and mechanical properties of AZ80-2Sn alloy were investigated. The results show that the addition of Bi within the as-cast AZ80-2Sn alloy promotes the formation of Mg3Bi2 phase, which can refine the grains and make the eutectic phases discontinuous. The addition of 0.5 % Bi within the as-extruded AZ80-2Sn alloy, the average grain size decreases to 12 μm and the fine granular Mg17Al12 and Mg3Bi2 phases are dispersed in the α-Mg matrix. With an increase in Bi content, the Mg17Al12 and Mg3Bi2 phases become coarsened and the grain size increases. The as-extruded AZ80-2Sn-0.5 %Bi alloy has the optimal properties, and the ultimate tensile strength, yield strength and elongation are 379.6 MPa, 247.1 MPa and 14.8 %, respectively.

Sign in / Sign up

Export Citation Format

Share Document