Research on the Simulation of the Charge Mathematical Model of the Vehicle Starting Battery

2013 ◽  
Vol 680 ◽  
pp. 479-483
Author(s):  
Pei Ying Li ◽  
Yu Tian Pan
Keyword(s):  
Mathematical Model ◽  
Battery Life ◽  
Model Parameters ◽  
Analysis Method ◽  
Lead Acid Battery ◽  
Battery Charge ◽  
Charge Model ◽  
Simulation Results ◽  
The Mathematical Model ◽  
Lead Acid

In order to meet the demands of practical, convenient and quick charge requirements, a mathematical model of a certain type of vehicle starting lead-acid battery is established. Using the method of circuit analysis, the model parameters are identified by the known test data. In addition, battery charge model is simulated in each charge stage using the intelligent three-stage charge method, simulation waveform and test waveform fit very well, absolute errors between them reach to 10-6. Simulation results show that the mathematical model and its analysis method is proper for the charge characteristics of vehicle starting lead-acid battery. This has a good guidance to design intelligent charger and extend the battery life.

Research on Dynamic Balance Method of Precision Centrifuge

2014 ◽  
Vol 945-949 ◽  
pp. 777-780
Author(s):  
Tao Liu ◽  
Yong Xu ◽  
Bo Yuan Mao
Keyword(s):  
Mathematical Model ◽  
Balance Control ◽  
Dynamic Balance ◽  
Dynamic Balancing ◽  
Structure Characteristics ◽  
Balance System ◽  
Simulation Results ◽  
Set Up ◽  
System Controller ◽  
The Mathematical Model

Firstly, according to the structure characteristics of precision centrifuge, the mathematical model of its dynamic balancing system was set up, and the dynamic balancing scheme of double test surfaces, double emendation surfaces were established. Then the dynamic balance system controller of precision centrifuge was designed. Simulation results show that the controller designed can completely meet the requirements of precision centrifuge dynamic balance control system.

The Impact Analysis of Revolute Pair Clearance to the End Pose Accuracy of Welding Robot

2015 ◽  
Vol 778 ◽  
pp. 259-263
Author(s):  
Fa Jun Zhang ◽  
Lin Zi Li ◽  
Hui Lin ◽  
Yin Lin Pu ◽  
Zhu Xin
Keyword(s):  
Mathematical Model ◽  
Impact Analysis ◽  
Joint Clearance ◽  
Welding Robot ◽  
Movement Characteristic ◽  
Movement Stability ◽  
Simulation Results ◽  
The Impact ◽  
The Mathematical Model ◽  
Welding Position

Various uncertain factors affect the movement of the welding robot, thus welding gun tend to deviate from the theory of welding position which reduces the welding accuracy, of which the revolute pair clearance have an greater effect on the movement of the welding robot. In order to study the influence of revolute pair clearance to the end pose accuracy of welding robot, the mathematical model of revolute pair clearance was established, and the software SolidWorks was used for establishing the welding robot model, making simulations of the mechanical arm with joint clearance and no joint clearance. At last, the movement characteristic of the hinge shaft is attained. The simulation results showed that the shaft velocity and displacement of mechanical arm with joint clearance has a certain degree of fluctuation, which affecting the end pose accuracy of welding robot , and reducing the movement stability and the welding accuracy of welding robot.

Methods of Mathematical Modeling of the Leaching Process of Cobalt-Containing Solutions

2021 ◽  
Vol 316 ◽  
pp. 661-666
Author(s):  
Nataliya V. Mokrova
Keyword(s):  
Mathematical Modeling ◽  
Mathematical Model ◽  
Chemical Kinetics ◽  
Group Method ◽  
Data Handling ◽  
Multistage Processes ◽  
Leaching Process ◽  
Proposed Model ◽  
Simulation Results ◽  
The Mathematical Model

Current cobalt processing practices are described. This article discusses the advantages of the group argument accounting method for mathematical modeling of the leaching process of cobalt solutions. Identification of the mathematical model of the cascade of reactors of cobalt-producing is presented. Group method of data handling is allowing: to eliminate the need to calculate quantities of chemical kinetics; to get the opportunity to take into account the results of mixed experiments; to exclude the influence of random interference on the simulation results. The proposed model confirms the capabilities of the group method of data handling for describing multistage processes.

Deep and Shallow Water Low-Speed Maneuvering Tests: Comparison Between Experimental and Simulation Results

2016 ◽  
Author(s):  
Felipe Ribolla Masetti ◽  
Pedro Cardozo de Mello ◽  
Guilherme F. Rosetti ◽  
Eduardo A. Tannuri
Keyword(s):  
Mathematical Model ◽  
Small Scale ◽  
Shallow Waters ◽  
Hydrodynamic Coefficients ◽  
Low Speed ◽  
Tunnel Model ◽  
Oceanographic Research ◽  
Simulation Results ◽  
The University ◽  
The Mathematical Model

This paper presents small-scale low-speed maneuvering tests with an oceanographic research vessel and the comparison with mathematical model using the real time maneuvering simulator developed by the University of São Paulo (USP). The tests are intended to verify the behavior of the vessel and the mathematical model under transient and low speed tests. The small-scale tests were conducted in deep and shallow waters, with a depth-draft ratio equal to 1.28, in order to verify the simulator ability to represent the vessel maneuverability on both depth conditions. The hydrodynamic coefficients used in the simulator model were obtained by CFD calculations and wind tunnel model tests carried out for this vessel. Standard turning circle and accelerating turn maneuvers were used to compare the experimental and numerical results. A fair agreement was achieved for shallow and deep water. Some differences were observed mainly in the initial phase of the accelerating turn test.

scholarly journals Population Behavior in the Mathematical Model of the Spread of COVID19 Type SEIRS

2021 ◽  
Vol 6 (2) ◽  
pp. 83-88
Author(s):  
Asmaidi As Med ◽  
Resky Rusnanda
Keyword(s):  
Mathematical Modeling ◽  
Numerical Simulation ◽  
Mathematical Model ◽  
Everyday Life ◽  
Applied Mathematics ◽  
Living Things ◽  
Simulation Results ◽  
Parameter Values ◽  
The Mathematical Model ◽  
Disease Free

Mathematical modeling utilized to simplify real phenomena that occur in everyday life. Mathematical modeling is popular to modeling the case of the spread of disease in an area, the growth of living things, and social behavior in everyday life and so on. This type of research is included in the study of theoretical and applied mathematics. The research steps carried out include 1) constructing a mathematical model type SEIRS, 2) analysis on the SEIRS type mathematical model by using parameter values for conditions 1and , 3) Numerical simulation to see the behavior of the population in the model, and 4) to conclude the results of the numerical simulation of the SEIRS type mathematical model. The simulation results show that the model stabilized in disease free quilibrium for the condition  and stabilized in endemic equilibrium for the condition .

scholarly journals The identification of a device based on a Peltier element by the least squares method

2020 ◽  
pp. 17-27
Author(s):  
Vladimir Grinkevich ◽  
Keyword(s):  
Mathematical Model ◽  
Least Squares ◽  
Least Squares Method ◽  
Control Object ◽  
Object Identification ◽  
Model Parameters ◽  
Peltier Element ◽  
Transport Delay ◽  
Non Linear ◽  
The Mathematical Model

The evaluation of the mathematical model parameters of a non-linear object with a transport delay is considered in this paper. A temperature controlled stage based on a Peltier element is an identification object in the paper. Several input signal implementations are applied to the input of the identification object. The least squares method is applied for the calculation of the non-linear differential equitation parameters which describe the identification object. The least squares method is used due to its simplicity and the possibility of identification non-linear objects. The parameters values obtained in the process of identification are provided. The plots of temperature changes in the temperature control system with a controller designed based on the mathematical model of the control object obtained as a result of identification are shown. It is found that the mathematical model obtained in the process of identification may be applied to design controllers for non-linear systems, in particular for a temperature stage based on a Peltier element, and for self-tuning controllers. However, the least square method proposed in the paper cannot estimate the transport delay time. Therefore it is required to evaluate the time delay by temperature transient processes. Dynamic object identification is applied when it is required to obtain a mathematical model structure and evaluate the parameters by an input and output control object signal. Also, identification is applied for auto tuning of controllers. A mathematical model of a control object is required to design the controller which is used to provide the required accuracy and stability of control systems. Peltier elements are applied to design low-power and small- size temperature stage . Hot benches based on a Peltier element can provide the desired temperature above and below ambient temperature.

scholarly journals A mathematical model of common-cold epidemics on Tristan da Cunha

1971 ◽  
Vol 69 (3) ◽  
pp. 423-433 ◽  
Author(s):  
B. J. Hammond ◽  
D. A. J. Tyrrell
Keyword(s):  
Mathematical Model ◽  
Common Cold ◽  
Average Duration ◽  
Model Parameters ◽  
Epidemic Threshold ◽  
Tristan Da Cunha ◽  
Simulation Techniques ◽  
Time Courses ◽  
The Mathematical Model ◽  
Computer Simulation Techniques

SUMMARYRecords of seven common-cold outbreaks on the island of Tristan da Cunha are compared with the corresponding time courses given by the mathematical model of Kermack & McKendrick (1927) and with an alternative model that directly involves a constant average duration of individual infection. Using computer simulation techniques the latter model is shown to be preferred and is then closely matched to the field data to obtain values for the model parameters. Consideration is then given to the intensity of epidemics predicted by the model and to the distribution of the actual epidemics relative to the theoretical epidemic threshold.

scholarly journals The generation of a mathematical model of the biogas production process from organic municipal solid waste

2020 ◽  
Vol 180 ◽  
pp. 02019 ◽  
Author(s):  
Marzhan Temirbekova ◽  
Madina Aliyarova ◽  
Iliya Iliev ◽  
Aliya Yelemanova ◽  
Saule Sagintayeva
Keyword(s):  
Mathematical Model ◽  
Municipal Solid Waste ◽  
Solid Waste ◽  
Anaerobic Fermentation ◽  
Biogas Production ◽  
Biogas Plant ◽  
Model Parameters ◽  
Biochemical Processes ◽  
Biogas Plants ◽  
The Mathematical Model

This paper justifies the efficiency of the biogas collection and utilization at the MSW (municipal solid waste) landfill in Almaty with the installation of several modern biogas plants. The optimal mode of processes occurring in a biogas plant is determined by computer generated simulations. Mathematical model parameters were identified to describe biochemical processes occurring in a biogas plant. Two approaches are used to resolve the mathematical model: the finite-difference method for solving the system of differential equations and simulation modeling by using the Any Logic package. A program is written in the algorithmic language C ++. Numerous calculations were carried out, the results of which are presented in curves and their qualitative picture is consistent with the ongoing processes. The created computer program allows to make a preliminary forecast of anaerobic fermentation occurring in the bioreactor depending on volume of the substrate, methane microorganisms and temperature conditions.

scholarly journals Online Parameter Identification and State of Charge Estimation of Battery Based on Multitimescale Adaptive Double Kalman Filter Algorithm

2020 ◽  
Vol 2020 ◽  
pp. 1-20
Author(s):  
Wenxian Duan ◽  
Chuanxue Song ◽  
Yuan Chen ◽  
Feng Xiao ◽  
Silun Peng ◽  
...  
Keyword(s):  
Kalman Filter ◽  
Parameter Identification ◽  
Unscented Kalman Filter ◽  
Least Square Method ◽  
State Of Charge ◽  
Least Square ◽  
Accurate Estimation ◽  
Battery Life ◽  
Model Parameters ◽  
Simulation Results

An accurate state of charge (SOC) can provide effective judgment for the BMS, which is conducive for prolonging battery life and protecting the working state of the entire battery pack. In this study, the first-order RC battery model is used as the research object and two parameter identification methods based on the least square method (RLS) are analyzed and discussed in detail. The simulation results show that the model parameters identified under the Federal Urban Driving Schedule (HPPC) condition are not suitable for the Federal Urban Driving Schedule (FUDS) condition. The parameters of the model are not universal through the HPPC condition. A multitimescale prediction model is also proposed to estimate the SOC of the battery. That is, the extended Kalman filter (EKF) is adopted to update the model parameters and the adaptive unscented Kalman filter (AUKF) is used to predict the battery SOC. The experimental results at different temperatures show that the EKF-AUKF method is superior to other methods. The algorithm is simulated and verified under different initial SOC errors. In the whole FUDS operating condition, the RSME of the SOC is within 1%, and that of the voltage is within 0.01 V. It indicates that the proposed algorithm can obtain accurate estimation results and has strong robustness. Moreover, the simulation results after adding noise errors to the current and voltage values reveal that the algorithm can eliminate the sensor accuracy effect to a certain extent.

Sign in / Sign up

Export Citation Format

Share Document