Study of the Impact of Rice Straw Particle Size on the Mechanical and Thermal Properties of Straw Lime Concretes

2022 ◽  
Author(s):  
Youssef El Moussi ◽  
Laurent Clerc ◽  
Jean-Charles Benezet
Keyword(s):  
Thermal Conductivity ◽  
Particle Size ◽  
Compressive Strength ◽  
Thermal Properties ◽  
Water Absorption ◽  
Rice Straw ◽  
Absorption Capacity ◽  
Mechanical And Thermal Properties ◽  
Water Absorption Capacity ◽  
The Impact

The use of bio-based concretes performed with lignocellulosic aggregates constitute an interesting solution for reducing the energy consumption, greenhouse gas emissions and CO2 generated by the building sector. Indeed, bio-based materials could be used as an alternative of traditional materials such as expended polystyrene and mineral resources (e.g. glass and rock wools) for insulation. Furthermore, these bio-based concretes are known for their interesting insulation properties, indeed they allow to enhance thermal properties of buildings and enables moisture management which lead to design efficient building materials. For this purpose, bio-based concrete using rice straw as aggregate are studied in this present work. The impact of the characteristics of rice straw particle (particle size distribution, bulk density, and water absorption capacity, etc.) on both the mechanical and thermal properties of the bio-based concrete are investigated. Five formulations of rice straw concrete are examined, compared and then classified in terms of insulation properties and mechanical properties. The assessments are based on the measurement of density and thermal conductivity. The variation of compressive strength in function of the characteristics (mean particle length) of rice straw particle are assessed and discussed. The investigation covers also the porosity and density. Tests are also carried out on agricultural by-products with a view to highlight their chemical, physical and structural proprieties. The results show that the use of large particles with low water absorption capacity induce lighter concretes with the density between 339 and 505 kg/m3 and lead to a high compressive strength with a high mechanical deformability. Furthermore, it appears that an increase in the average length of rice straw particle lead to decrease of thermal conductivity of bio-based concretes. It varies from 0.062 to 0.085 W/(m.K).

Effect of Nanosilica on Mechanical and Thermal Properties of Cement Composites for Thermal Energy Storage Materials

2015 ◽  
Vol 1131 ◽  
pp. 182-185
Author(s):  
Pongsak Jittabut
Keyword(s):  
Thermal Conductivity ◽  
Particle Size ◽  
Heat Capacity ◽  
Compressive Strength ◽  
Thermal Properties ◽  
Thermal Energy ◽  
Energy Storage Materials ◽  
Mechanical And Thermal Properties ◽  
Storage Materials ◽  
Nanosilica Particle

This research article presents the mechanical and thermal properties of cement-based composite for thermal energy storage materials. The effects of nanosilica particle size and concentration determined by mixing nanosilica particle size of 50 nm, using nanosilica were of 1-5 wt%. Thermal properties coefficients were tested using a direct measuring instrument with surface probe (ISOMET2114). The influence of nanosilica on the performance, such as compressive strength, bulk density, thermal conductivity, volume heat capacity and thermal diffusivity of hardened composite cement pastes were studied for future solar thermal energy materials with better performance. According to the development of thermal storage materials and their application environment requirement in solar thermal power, the specimens were subjected to heat at 350, and 900°C. It were observed that, before heating, the compressive strength is optimized at nanosilica amount of 4wt% at the age of 28 days. Moreover, after heating at 350 oC and 900°C, the thermal conductivity and volume heat capacity of the cement paste enriched with nanosilica were significantly lesser than that of the before heating one.

Comparison of Bio and Eco-technologies with Chemical Methods for Pre-treatment of Flax Fibers: Impact on Fiber Properties

2014 ◽  
Vol 9 (4) ◽  
pp. 155892501400900 ◽  
Author(s):  
Sabela Camano ◽  
Nemeshwaree Behary ◽  
Philippe Vroman ◽  
Christine Campagne
Keyword(s):  
Water Absorption ◽  
Fiber Bundle ◽  
Glass Fibers ◽  
Fiber Surface ◽  
Pectate Lyase ◽  
High Water ◽  
Absorption Capacity ◽  
Water Absorption Capacity ◽  
Flax Fibers ◽  
The Impact

Flax fibers, available as fiber bundles, are commonly used as fiber reinforcement in composite materials as a substitute for glass fibers. Pre-treatments are often necessary for improving fiber-resin adhesion, and also to facilitate fiber elementarization, and to improve fiber ability to be implemented in mechanical processes limiting fiber damages. This paper focuses on the impact of biotechnologies (effect of 2 different enzymes: a pectate lyase and a laccase) and of an ecotechnology (ultrasound with ethanol), compared to classical chemical pre-treatments (using aqueous NaOH and ammonia) on the final flax fiber bundle properties, before and after a carding process. Fiber surface properties (wettability and/or zeta potential values), fiber elementarization and mechanical properties vary with the type of treatment (chemical nature of product and conditions used). Fibers elementarised using pectate lyase and ultrasound/ethanol have a hydrophilic surface and a high water absorption capacity, and are also of highest quality in terms of increased fineness. Treatment with NaOH yields the poorest fiber bundle tenacity. Laccase enzyme yields long thick hydrophobic fibers having very low water absorption capacity, and the most neutral surface charge. Properties of flax fibers can be easily monitored using different pre-treatments resulting in fibers which would be suited for various final applications.

scholarly journals Bio-based rigid polyurethane foam prepared from apricot stone shell-based polyol for thermal insulation application – Part 2: Morphological, mechanical, and thermal properties

BioResources ◽  
2020 ◽  
Vol 15 (3) ◽  
pp. 6080-6094
Author(s):  
Muhammed Said Fidan ◽  
Murat Ertaş
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Thermal Properties ◽  
Thermogravimetric Analysis ◽  
Polyurethane Foam ◽  
Flame Retardants ◽  
Compressive Modulus ◽  
Cell Diameter ◽  
Mechanical And Thermal Properties ◽  
Rigid Polyurethane Foam

The procedure for the liquefaction of apricot stone shells was reported in Part 1. Part 2 of this work determines the morphological, mechanical, and thermal properties of the bio-based rigid polyurethane foam composites (RPUFc). In this study, the thermal conductivity, compressive strength, compressive modulus, thermogravimetric analysis, flammability tests (horizontal burning and limited oxygen index (LOI)) in the flame retardants), and scanning electron microscope (SEM) (cell diameter in the SEM) tests of the RPUFc were performed and compared with control samples. The results showed the thermal conductivity (0.0342 to 0.0362 mW/mK), compressive strength (10.5 to 14.9 kPa), compressive modulus (179.9 to 180.3 kPa), decomposition and residue in the thermogravimetric analysis (230 to 491 °C, 15.31 to 21.61%), UL-94 and LOI in the flame retardants (539.5 to 591.1 mm/min, 17.8 to 18.5%), and cell diameter in the SEM (50.6 to 347.5 μm) of RPUFc attained from liquefied biomass. The results were similar to those of foams obtained from industrial RPUFs, and demonstrated that bio-based RPUFc obtained from liquefied apricot stone shells could be used as a reinforcement filler in the preparation of RPUFs, specifically in construction and insulation materials. Moreover, liquefied apricot stone shell products have potential to be fabricated into rigid polyurethane foam composites.

scholarly journals OPTIMUM PERFORMANCE OF STABILIZED EDE LATERITE AS AN ALTERNATIVE CONSTRUCTION MATERIAL

2020 ◽  
Vol 3 (8) ◽  
pp. 1-8
Author(s):  
Adegbenle Bukunmi O
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Construction Material ◽  
High Water ◽  
Good Alternative ◽  
Linear Shrinkage ◽  
Absorption Capacity ◽  
Water Absorption Capacity ◽  
Optimum Performance ◽  
High Water Absorption

Laterite samples from Ede area with particle components of 19.7% clay, 32.8% silt and 47.5% sand was stabilized with combined cement, lime and bitumen and test for Compressive strength, Linear Shrinkage, Permeability and Water Absorption. The stabilizers were mixed with laterite soil in different ratios and percentage. The laterite carried 90% which is constant while the three stabilizers shared the remaining 10% in varying form. After 28 days of curing, laterite stabilizer with 90% of laterite, 8% of cement, 1% lime and 1% bitumen (LCLB1) possessed compressive strength of 2.01N/mm2. It Water Absorption Capacity was 3.05%. LCLB4 stabilizer (90% laterite, 6% cement, 2% lime and 2% bitumen) has the same compressive strength with LCLB1 stabilizer but with a high Water Absorption Capacity of 4.2%. The stabilizer of 90% laterite, 3.33% cement, 3.33% lime and 3.33% of bitumen (LCLB8) has the lowest compressive strength of 0.74N/mm2 and the highest Water Absorption Capacity of 5.39%. The results shows that LCLB1 stabilizer is a better stabilizer for strength and blocks made from laterite stabilized with it stand a good alternative to sand Crete blocks in building constructions. The combination of these stabilizers in order to determine a most economical volume combination for optimum performance is highly possible and economical.

Investigation of Physical, Mechanical and Thermal Properties of Building Wall Materials

2017 ◽  
Vol 751 ◽  
pp. 521-526 ◽  
Author(s):  
Jiraphorn Mahawan ◽  
Somchai Maneewan ◽  
Tanapon Patanin ◽  
Atthakorn Thongtha
Keyword(s):  
Compressive Strength ◽  
Thermal Properties ◽  
Water Absorption ◽  
Calcium Silicate Hydrate ◽  
Lightweight Concrete ◽  
Physical And Mechanical Properties ◽  
Mechanical And Thermal Properties ◽  
Thermal Insulating ◽  
Building Wall ◽  
Wall Materials

This research concentrates to the effect of changing sand proportion on the physical, mechanical and thermal properties of building wall materials (Cellular lightweight concrete). The density, water absorption and compressive strength of the 7.0 cm x 7.0 cm x 7.0 cm concrete sample were studied. It was found that there are an increase of density and a reduction of water absorption with an increase of sand content. The higher compressive strength can be confirmed by higher density and lower water absorption. The physical and mechanical properties of lightweight concrete conditions conformed to the Thai Industrial Standard 2601-2013. The phases of CaCO3 and calcium silicate hydrate (C-S-H) in the material indicate an important factor in thermal insulating performance.

scholarly journals Physical Properties of Soy-Phosphate Polyol-Based Rigid Polyurethane Foams

2012 ◽  
Vol 2012 ◽  
pp. 1-8 ◽  
Author(s):  
Hongyu Fan ◽  
Ali Tekeei ◽  
Galen J. Suppes ◽  
Fu-Hung Hsieh
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Thermal Properties ◽  
Water Content ◽  
Polyurethane Foams ◽  
Solid Polymer ◽  
Mechanical And Thermal Properties ◽  
Blowing Agent ◽  
Isocyanate Index ◽  
Pu Foams

Water-blown rigid polyurethane (PU) foams were made from 0–50% soy-phosphate polyol (SPP) and 2–4% water as the blowing agent. The mechanical and thermal properties of these SPP-based PU foams (SPP PU foams) were investigated. SPP PU foams with higher water content had greater volume, lower density, and compressive strength. SPP PU foams with 3% water content and 20% SPP had the lowest thermal conductivity. The thermal conductivity of SPP PU foams decreased and then increased with increasing SPP percentage, resulting from the combined effects of thermal properties of the gas and solid polymer phases. Higher isocyanate density led to higher compressive strength. At the same isocyanate index, the compressive strength of some 20% SPP foams was close or similar to the control foams made from VORANOL 490.

The Study on Physical and Thermal Properties of Geopolymer Pastes

2017 ◽  
Vol 751 ◽  
pp. 538-543 ◽  
Author(s):  
Pongsak Jittabut
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Thermal Properties ◽  
Water Absorption ◽  
Sodium Hydroxide ◽  
Bulk Density ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Weight Ratio ◽  
Thermal Capacity

This research was aimed to a present the physical and thermal properties of geopolymer pastes made of fly ash (FA) and bagasse ash (BA) with rice husk ash (RHA) containing at the doses of 0%, 2%, 4%, 6%, 8% and 10% by weight. The sodium hydroxide concentration of 15 molars, sodium silicate per sodium hydroxide by weight ratio of 2.0, the alkaline liquid per binder at the ratio of 0.60 and curing at ambient temperature were used at the to mix all mixtures to gether for 7 and 28 days. The properties analysis of the geopolymer pastes such as compressive strength, bulk density, water absorption, thermal conductivity, thermal diffusivity and thermal capacity were tested. The results were indicated that geopolymer pastes that containing rice husk ash 2% by weight for 28 days of curing gave the maximum compressive strength of 84.42 kg/cm2, low water absorption of 1.16 %, low bulk density of 2,065.71 kg/cm3, lower thermal conductivity of 1.1173 W/m.K, lower thermal diffusion of 6.643 µm2/s and lower thermal capacity of 1.6819 MJ/m3K, respectively. The utilization of waste from agriculture industry via geopolymer pastes for green building materials can be achieved. For this research, physical properties and thermal insulation of geopolymer pastes were siqnificantly improved.

On Mechanical and Thermal Properties of Epoxy/Graphene Nanocomposites

2018 ◽  
Vol 22 ◽  
pp. 23-33 ◽  
Author(s):  
Seenaa I. Hussein
Keyword(s):  
Thermal Conductivity ◽  
Thermal Properties ◽  
Impact Strength ◽  
Mechanical And Thermal Properties ◽  
Graphene Nanocomposites ◽  
Graphene Composite ◽  
Efficiency Increase ◽  
Graphene Content ◽  
The Impact ◽  
Thermal Stability Of

In this research, we have prepared epoxy/graphene nanocomposites (graphene content: 1, 3, 5, 7, and 9 wt%) to investigate some mechanical (impact strength, hardness, and Brazilian tests) and thermal properties (thermal conductivity and thermogravimetric analysis). Our results show that the impact strength, hardness, and compression strength values increased to 5.04 kJ/m2, 79.8, and 27.85 MPa, respectively, as increasing graphene content up to 5 wt% and then decreased for further increasing of the graphene content. The observed reduction in the hardness could be attributed to the samples brittleness. On the other hand, the thermal conductivity increased with increasing the graphene content because of the high thermal conductivity of graphene and thus the efficiency increase with increasing of graphene content. In addition, the thermal stability of epoxy/graphene composite increase compared with pure epoxy resin, while the activation energy for samples consists of 9 wt% graphene greater than those containing 1 wt% graphene.

Mechanical and Thermal Properties of PCM Wallboards Based on Gypsum and Paraffin

2011 ◽  
Vol 71-78 ◽  
pp. 3553-3557
Author(s):  
Xiao Peng Wang ◽  
Zhen Qiu Shen ◽  
Yi Zhang ◽  
Dong Xu Li
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Thermal Properties ◽  
Energy Consumption ◽  
Building Energy ◽  
Building Envelope ◽  
Mechanical And Thermal Properties ◽  
Building Energy Consumption

This paper studied on preparation, mechanical and thermal properties of two PCM wallboards made of gypsum and paraffin composite, PCM particles wallboard and PCM bag packed wallboard. Density, flexural and compressive strength and thermal conductivity of PCM particles wallboards deceased as PCM particles dosage increasing. Only PCM particles wallboard with PCM particles dosage 30% is suitable. Thermal comparison between PCM wallboards and pure gypsum wallboard shows that two PCM wallboards have better thermal properties and PCM wallboards can be used in building envelope to cut down building energy-consumption.

Sign in / Sign up

Export Citation Format

Share Document