Influence of Sintering Conditions on Electric Performance of Textured 92BNT-6BT-2KNN Ceramics

2012 ◽  
Vol 512-515 ◽  
pp. 1380-1384 ◽  
Author(s):  
Cheng Gen Ye ◽  
Fang Fu ◽  
Bo Shen ◽  
Ji Wei Zhai
Keyword(s):  
Phase Transformation ◽  
Volume Change ◽  
Temperature Increase ◽  
Grain Orientation ◽  
Sintering Temperature ◽  
Sintering Process ◽  
Templated Grain Growth ◽  
Soaking Time ◽  
Sintering Conditions ◽  
Lotgering Factor

0.92(Bi0.5Na0.5)TiO3-0.06BaTiO3-0.02(K0.5Na0.5)NbO3(92BNT-6BT-2KNN) is a high-stain material due to the volume change which come from antiferroelectric-ferroelectric (AFE-FE) phase transformation. Textured 92BNT-6BT-2KNN with a Lotgering factor of 67% was obtained by templated grain growth (TGG) method using plate-like (Bi0.5Na0.5)TiO3（BNT）particles as templates. The influences of sintering process on Lotgering factor and strain were investigated. It was found that the Lotgering factor increased as sintering temperature increase and then decreased with further temperature increase. The changing tendency of polar and unipolar strain did not keep the same accordance with that of Lotgering factor. The maximum of Lotgering factor (79%) and polar strain (0.36%) was obtained when the sintering temperature was 1240°C and 1220°C, respectively, due to the decrease of density when high sintering temperature was employed. Also it was found that the lotgering factor and polar strain reached its highest values when the soaking time was 4h. All these proved that the density and grain orientation codetermined the strain of 92BNT-6BT-2KNN ceramics.

Fabrication of Textured SrBi2Nb2O9 Ceramics by Templated Grain Growth

2007 ◽  
Vol 26-28 ◽  
pp. 239-242 ◽  
Author(s):  
Chun Wei Cui ◽  
Jin Liang Huang ◽  
Lin Hua Gao ◽  
Xing Hua Yang ◽  
Xiao Wang
Keyword(s):  
Relative Density ◽  
Molten Salt ◽  
Grain Growth ◽  
Grain Orientation ◽  
Sintering Temperature ◽  
Molten Salt Method ◽  
Templated Grain Growth ◽  
Increasing Temperature ◽  
Lotgering Factor ◽  
Peak Value

Textured SrBi2Nb2O9 (SBN) ceramics were fabricated by templated grain growth (TGG) method. The plated-like SBN particles with shape anisotropy prepared by molten salt method were used as the templates. The SBN powders prepared by conventional solid (CS) reaction were used as matrix powders. It was found that the textured SBN ceramics can be obtained by TGG method. The grain orientation (Lotgering factor, f) increased with the increase of sintering temperature and content of the templates. The textured SBN ceramics with f=0.86 could then be obtained after sintering at 1300 °C for 3 h with 20wt.% templates. The relative density keeps rising with increasing temperature until it reaches a peak value 91.22% at the sintering temperature 1300°C, after which it decreases.

Effects of Sintering Process on the Properties of Ti3SiC2/Cu Composite

2012 ◽  
Vol 512-515 ◽  
pp. 377-381 ◽  
Author(s):  
Jin Rong Lu ◽  
Yang Zhou ◽  
Yong Zheng ◽  
Shi Bo Li ◽  
Zhen Ying Huang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Vickers Hardness ◽  
Hot Pressing ◽  
Sintering Temperature ◽  
Sintering Process ◽  
Vacuum Sintering ◽  
New Type ◽  
Sintering Conditions ◽  
The Relationship ◽  
Better Than

In this paper, a new type of Ti3SiC2/Cu composites with the volume fractions of 30% Ti3SiC2 particle was prepared by hot pressing and vacuum sintering respectively. The effects of sintering temperature and holding time on the density, resistance and Vickers hardness of Cu-30vol%Ti3SiC2 composite were investigated. The results show that the mechanical properties of the composites prepared by hot pressing are better than that prepared by vacuum sintering. The relative densities of Cu-30vol% Ti3SiC2 composites are rather high in suitable sintering conditions. It achieved 100% for the composites prepared by hot pressing at 930°C for 2h, and 98.4% for the composites prepared by vacuum sintering at 1250°C for 1h. At the same time, the maximum Vickers hardness reached 1735MPa at 900°C by hot pressing. The resistance and Vickers hardness of the composites decreased with an increase in sintering temperature, whereas the density increased. Scanning electron microscope (SEM) and energy-dispersive spectroscopy (EDS) were used to observe the microstructure of the composites. The relationship between microstructure and mechanical properties was discussed.

Effect of Sintering Parameter on Ferroelectric Properties in PZT Based Ceramics

2015 ◽  
Vol 804 ◽  
pp. 34-37
Author(s):  
Tanabat Promjun ◽  
Yongyut Manjit ◽  
Saksit Sukprasong ◽  
Athipong Ngamjarurojana
Keyword(s):  
Mixed Oxide ◽  
Perovskite Structure ◽  
Sintering Temperature ◽  
Ferroelectric Properties ◽  
Pyrochlore Phase ◽  
Soaking Time ◽  
Sintering Conditions ◽  
Xrd Patterns ◽  
Sintering Condition

This research was conducted to improve the ferroelectric properties of PZT based ceramics by studying the effect of sintering conditions in terms of temperature and soaking time (time of sintering) on the ferroelectric properties of ceramics in the 0.8Pb (Zr1/2Ti1/2)O3-0.2Pb (Zn1/3Nb2/3)O3 system prepared by vibro-milling mixed-oxide method. The XRD patterns of specimens showed perovskite structure for all compositions. The pyrochlore phase was not observed in this system. The sintering temperature and soaking time affects the ferroelectric properties of ceramics by the optimum sintering condition for 0.8PZT-0.2PZN ceramic is sintered at 1250°C for 2h.

Preparation and Characterization of Al2TiO5- Si3N4 Composites by Reaction Sintering Process

2011 ◽  
Vol 284-286 ◽  
pp. 201-204
Author(s):  
Rui Sheng Wang ◽  
Jun Hong Zhao ◽  
Heng Yong Wei ◽  
Shao Wei Yao
Keyword(s):  
Mechanical Strength ◽  
Sintering Temperature ◽  
Raw Materials ◽  
Reaction Sintering ◽  
Sintering Process ◽  
Soaking Time ◽  
Sintering Properties ◽  
The One

Al2TiO5-Si3N4 composites were prepared by reaction sintering process using Al2TiO5 and α-Si3N4 powders as raw materials. The effect ofsintering temperature, soaking time and Si3N4 content on the sintering properties of the composites was studied. The results showed that the best sintering temperature and soaking time were 1550 °C and 2 h, respectively. The samples with 15 wt% of Si3N4 addition had good sintering properties, and its mechanical strength was 28.96 MPa, which was 2 times of the one of the samples without Si3N4 addition.

scholarly journals Pressureless Sintering of YIG Ceramics from Coprecipitated Nanopowders

2021 ◽  
Vol 7 (5) ◽  
pp. 56
Author(s):  
Yimin Yang ◽  
Xiaoying Li ◽  
Ziyu Liu ◽  
Dianjun Hu ◽  
Xin Liu ◽  
...  
Keyword(s):  
High Temperature ◽  
Calcination Temperature ◽  
Sintering Temperature ◽  
Raw Materials ◽  
Secondary Phase ◽  
Coprecipitation Method ◽  
Pressureless Sintering ◽  
Densification Behavior ◽  
Sintering Process

Nanoparticles prepared by the coprecipitation method were used as raw materials to fabricate Y3Fe5O12 (YIG) ceramics by air pressureless sintering. The synthesized YIG precursor was calcinated at 900–1100 °C for 4 h in air. The influences of the calcination temperature on the phase and morphology of the nanopowders were investigated in detail. The powders calcined at 1000–1100 °C retained the pure YIG phase. YIG ceramics were fabricated by sintering at 1200–1400 °C for 10 h, and its densification behavior was studied. YIG ceramics prepared by air sintering at 1250 °C from powders calcinated at 1000 °C have the highest in-line transmittance in the range of 1000-3000 nm. When the sintering temperature exceeds 1300 °C, the secondary phase appears in the YIG ceramics, which may be due to the loss of oxygen during the high-temperature sintering process, resulting in the conversion of Fe3+ into Fe2+.

scholarly journals Microwave Sintering and Microwave Dielectric Properties of (1–x)Ca0.61La0.26TiO3-xNd(Mg0.5Ti0.5)O3 Ceramics

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 438
Author(s):  
Shuwei Yang ◽  
Bingliang Liang ◽  
Changhong Liu ◽  
Jin Liu ◽  
Caisheng Fang ◽  
...  
Keyword(s):  
Dielectric Properties ◽  
Mobile Communications ◽  
Sintering Temperature ◽  
Microwave Sintering ◽  
Microwave Dielectric Properties ◽  
Conventional Heating ◽  
Sintering Process ◽  
Microwave Dielectric ◽  
Sintering Time ◽  
Frequency Temperature

The (1–x)Ca0.61La0.26TiO3-xNd(Mg0.5Ti0.5)O3 [(1–x)CLT-xNMT, x = 0.35~0.60] ceramics were prepared via microwave sintering. The effects of sintering temperature and composition on the phase formation, microstructure, and microwave dielectric properties were investigated. The results show that the microwave sintering process requires a lower sintering temperature and shorter sintering time of (1–x)CLT-xNMT ceramics than conventional heating methods. All of the (1–x)CLT-xNMT ceramics possess a single perovskite structure. With the increase of x, the dielectric constant (ε) shows a downward trend; the quality factor (Qf) drops first and then rises significantly; the resonance frequency temperature coefficient (τf) keeps decreasing. With excellent microwave dielectric properties (ε = 51.3, Qf = 13,852 GHz, τf = −1.9 × 10−6/°C), the 0.65CLT-0.35NMT ceramic can be applied to the field of mobile communications.

Effects of Sintering Conditions on Properties of a Warm Compacted Stainless Steel Powder

2012 ◽  
Vol 217-219 ◽  
pp. 483-486
Author(s):  
Mei Yuan Ke
Keyword(s):  
Tensile Strength ◽  
Stainless Steel ◽  
Sintered Density ◽  
Sintering Temperature ◽  
Steel Powder ◽  
Stainless Steel Powder ◽  
Sintering Atmosphere ◽  
Comprehensive Properties ◽  
Ammonia Atmosphere ◽  
Sintering Conditions

Effects of Sintering atmosphere and temperature on properties of warm compacted 410L stainless steel powder were studied. Sintered density, hardness, tensile strength and elongation were measured. Results showed that in order to achieve high comprehensive properties, the optimal sintering temperature was 1230°C for 410L stainless steel powder. At the same sintering temperature, density and hardness sintered in vacuum were much higher than that sintered in cracked ammonia while tensile strength sintered in cracked ammonia were much higher than that in vacuum. When sintered in vacuum at 1230°C, sintered density was 7.45 g•cm-3, hardness was 65 HRB, tensile strength was 410 MPa and elongation was 29.5%. When sintered in cracked ammonia atmosphere at 1230°C, sintered density was 7.26 g•cm-3, hardness was 97 HRB, tensile strength was 515 MPa and elongation was 3.8%.

scholarly journals Phase Transformation of Kaolin-Ground Granulated Blast Furnace Slag from Geopolymerization to Sintering Process

2021 ◽  
Vol 7 (3) ◽  
pp. 32
Author(s):  
Noorina Hidayu Jamil ◽  
Mohd. Mustafa Al Bakri Abdullah ◽  
Faizul Che Pa ◽  
Mohamad Hasmaliza ◽  
Wan Mohd Arif W. Ibrahim ◽  
...  
Keyword(s):  
Phase Transformation ◽  
Blast Furnace ◽  
Blast Furnace Slag ◽  
Room Temperature ◽  
Curing Temperature ◽  
Curing Process ◽  
Sintering Process ◽  
Granulated Blast Furnace Slag ◽  
Fluxing Agent ◽  
Furnace Slag

The main objective of this research was to investigate the influence of curing temperature on the phase transformation, mechanical properties, and microstructure of the as-cured and sintered kaolin-ground granulated blast furnace slag (GGBS) geopolymer. The curing temperature was varied, giving four different conditions; namely: Room temperature, 40, 60, and 80 °C. The kaolin-GGBS geopolymer was prepared, with a mixture of NaOH (8 M) and sodium silicate. The samples were cured for 14 days and sintered afterwards using the same sintering profile for all of the samples. The sintered kaolin-GGBS geopolymer that underwent the curing process at the temperature of 60 °C featured the highest strength value: 8.90 MPa, and a densified microstructure, compared with the other samples. The contribution of the Na2O in the geopolymerization process was as a self-fluxing agent for the production of the geopolymer ceramic at low temperatures.

Sign in / Sign up

Export Citation Format

Share Document