Effects of Annealing Process on Mechanical Properties of Weather-Resistant Steel Welding Joints

2018 ◽  
Vol 777 ◽  
pp. 397-401
Author(s):  
Qiang Zhang ◽  
Zhe Wu ◽  
Hong Wu Li
Keyword(s):  
Mechanical Properties ◽  
Impact Energy ◽  
Welded Joints ◽  
Impact Test ◽  
Resistant Steel ◽  
Test Results ◽  
Before And After ◽  
Welding Joints ◽  
Weld Area ◽  
The Impact

In this paper, the mechanical properties of Q355NH resistant steel welded joints are studied. Through the analysis of mechanical properties of welded joints, the results showed that the tensile strength of the welded joints decreased after annealing and the elongation increased. The impact test results of tensile specimens before and after annealing showed that the impact energy of the weld area increased greatly after annealing, while the impact energy of the heat affected zone changed little. Furtherly, fatigue strength of specimens before and after annealing was compared, and the results showed that under the condition of high cycle fatigue, the un-annealed specimens were broken and the fracture position was located on the parent metal, whereas the annealed specimens did not break.

Influence of Temperature on Ductile-Fragile Behavior

2014 ◽  
Vol 802 ◽  
pp. 383-387
Author(s):  
C.A. Silva ◽  
R.C.R. Nascimento ◽  
M.S. Martins ◽  
M.C.S. Freitas
Keyword(s):  
Fracture Mode ◽  
Impact Energy ◽  
Impact Test ◽  
Evaluation Criteria ◽  
Test Body ◽  
Gravitational Potential Energy ◽  
Machine Component ◽  
Whole Process ◽  
Before And After ◽  
The Impact

The article to be presented will cover the whole process done in a fracture test for impact, taking into account the thermal treatment of the sample to be studied. The main objective of this article is to observe, verify, analyze and understand how the temperature difference of several samples influences the type and appearance of the fracture. The impact test have a great importance in industry, is through this that you can verify that the material is ideal for application in the production of equipment and vehicles that operate in high or low temperatures. The evaluation criteria of this trial are the energy absorbed by the sample, and the percentage of its characteristic lateral extension, and the percentage of fracture, ductile or fragile, and corresponding to a ductile fracture mode, in which the test at higher temperatures, the impact energy is relatively large, and fragile fracture mode, being one that as the temperature decreased, the impact energy will suffer decline. The most important result of the impact test is the measure of the energy absorbed by the test body to deform and break, measured by the variance of the gravitational potential energy of the hammer (machine component of the impact test) before and after impact. Therefore, providing the conclusion that the smaller the energy absorbed by the sample, more fragile it is depending on the temperature applied.

scholarly journals Degradation of Roller-Compacted Concrete Subjected to Freeze-Thaw Cycles and Immersion in Potassium Acetate Solution

2018 ◽  
Vol 2018 ◽  
pp. 1-8
Author(s):  
Wuman Zhang ◽  
Jingsong Zhang ◽  
Shuhang Chen ◽  
Sheng Gong
Keyword(s):  
Mechanical Properties ◽  
Weight Loss ◽  
Compressive Strength ◽  
Impact Energy ◽  
Impact Test ◽  
Potassium Acetate ◽  
Acetate Solution ◽  
Freeze Thaw ◽  
Roller Compacted Concrete ◽  
The Impact

Two sets of roller-compacted concrete (RCC) samples cured for 28 days were subjected to freeze-thaw (F-T) cycles and immersion in laboratory conditions. F-T cycles in water and water-potassium acetate solution (50% by weight) were carried out and followed by the flexural impact test. The weight loss, the dynamic elastic modulus (Ed), the mechanical properties, and the residual strain of RCC were measured. The impact energy was calculated based on the final number of the impact test. The results show that the effect of F-T cycles in KAc solution on the weight loss and Ed of RCC is slight. Ed, the compressive strength, and the flexural strength of RCC with 250 F-T cycles in KAc solution decrease by 3.8%, 23%, and 36%, respectively. The content (by weight) of K+ at the same depth of RCC specimens increases with the increase of F-T cycles. The impact energy of RCC specimens subjected to 250 F-T cycles in KAc solution decreases by nearly 30%. Microcracks occur and increase with the increase of F-T cycles in KAc solution. The compressive strength of RCC immersed in KAc solution decreases by 18.8% and 32.8% after 6 and 12 months. More attention should be paid to using KAc in practical engineering because both the freeze-thaw cycles and the complete immersion in KAc solution damage the mechanical properties of RCC.

Effect of Heat Treatment on Microstructure Evolution and Mechanical Behavior of SKLB3 Alloy

2017 ◽  
Vol 898 ◽  
pp. 380-386
Author(s):  
Wei Yuan ◽  
Dong Mei Liu ◽  
Qiang Song Wang ◽  
Guo Liang Xie
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Impact Energy ◽  
Hot Forging ◽  
Charpy Impact ◽  
Aging Treatment ◽  
Ni Alloy ◽  
Before And After ◽  
Different Temperatures ◽  
The Impact

In this paper, the effect of heat treatment on the microstructure and mechanical properties of hot forging Cu-Ni alloy was studied. Specimens of hot forged Cu-Ni alloy were subjected to first solution treated at 900oC for 2hrs and then aged at different temperatures for 2hrs. The mechanical properties including tensile performance and impact energy, and the microstructure were measured for specimens before and after heat treatment. The results show that both solution and aging treatment have an influence on the grain growth. After heat treatment, the tensile strength decreases very slightly but the yield strength decreases seriously from 235.96MPa to 136.12MPa, while the elongation increases sharply from 36% to 48%. It was also observed that hardness values of the heat-treated alloys are all lower than that of the hot forged alloy. The measurement of Charpy impact energy with V-type notch was performed at 298K and 77K for different specimens. At both temperatures, the impact energies of the specimens are higher than 200J. The microstructure results show that at both temperatures, the alloys are fractured in a ductile mode.

Tempering Temperature Effects on Hardness and Impact Toughness of 56NiCrMo7 Steel

2011 ◽  
Vol 56 (1) ◽  
pp. 5-11 ◽  
Author(s):  
R. Dąbrowski ◽  
R. Dziurka
Keyword(s):  
Impact Toughness ◽  
Tool Steel ◽  
Impact Energy ◽  
Temperature Effects ◽  
Test Specimen ◽  
Impact Test ◽  
Test Results ◽  
Tempering Temperature ◽  
Fracture Surfaces ◽  
The Impact

Tempering Temperature Effects on Hardness and Impact Toughness of 56NiCrMo7 Steel The assessment of the effect of tempering temperature on hardness and impact toughness of a 56NiCrMo7 grade hot work tool steel was presented in the paper. It has been found that the investigated steel, after quenching in oil from 800°C, softens quite slowly upon tempering within the range between 100 and 675°C, which was confirmed not only by hardness measurements but also by observed changes occurring in its microstructure, whereas the impact energy (KV) absorbed by the test specimen increases with temperature, achieving >66J after tempering at 675°C. The changes observed in the character of the fracture surfaces allows of interpretation of the impact test results for the whole range of tempering temperatures.

Sunlight exposure: the effects on the performance of paragliding fabric

2018 ◽  
Vol 69 (05) ◽  
pp. 381-389
Author(s):  
MENGÜÇ GAMZE SÜPÜREN ◽  
TEMEL EMRAH ◽  
BOZDOĞAN FARUK
Keyword(s):  
Mechanical Properties ◽  
Aging Process ◽  
Air Permeability ◽  
Sunlight Exposure ◽  
Test Results ◽  
Coating Materials ◽  
Strength Tests ◽  
Before And After ◽  
The Relationship ◽  
Dark Blue

This study was designed to explore the relationship between sunlight exposure and the mechanical properties of paragliding fabrics which have different colors, densities, yarn counts, and coating materials. This study exposed 5 different colors of paragliding fabrics (red, turquoise, dark blue, orange, and white) to intense sunlight for 150 hours during the summer from 9:00 a.m. to 3:00 p.m. for 5 days a week for 5 weeks. Before and after the UV radiation aging process, the air permeability, tensile strength, tear strength, and bursting strength tests were performed. Test results were also evaluated using statistical methods. According to the results, the fading of the turquoise fabric was found to be the highest among the studied fabrics. It was determined that there is a significant decrease in the mechanical properties of the fabrics after sunlight exposure. After aging, the fabrics become considerably weaker in the case of mechanical properties due to the degradation in both the dyestuff and macromolecular structure of the fiber

scholarly journals Impact resistance of steel materials to ballistic ejecta and shelter development using steel deck plates

2021 ◽  
Vol 10 (1) ◽  
Author(s):  
Hiroyuki Yamada ◽  
Kohei Tateyama ◽  
Shino Naruke ◽  
Hisashi Sasaki ◽  
Shinichi Torigata ◽  
...  
Keyword(s):  
Impact Energy ◽  
Impact Test ◽  
Impact Resistance ◽  
Protective Layer ◽  
High Strength ◽  
Steel Plates ◽  
Corrugated Plates ◽  
Shelter Construction ◽  
The Impact ◽  
Ballistic Ejecta

AbstractThe destruction caused by ballistic ejecta from the phreatic eruptions of Mt. Ontake in 2014 and Mt. Kusatsu-Shirane (Mt. Moto-Shirane) in 2018 in Japan, which resulted in numerous casualties, highlighted the need for better evacuation facilities. In response, some mountain huts were reinforced with aramid fabric to convert them into shelters. However, a number of decisions must be made when working to increase the number of shelters, which depend on the location where they are to be built. In this study, we propose a method of using high-strength steel to reinforce wooden buildings for use as shelters. More specifically, assuming that ballistic ejecta has an impact energy of 9 kJ or more, as in previous studies, we developed a method that utilizes SUS304 and SS400 unprocessed steel plates based on existing impact test data. We found that SUS304 is particularly suitable for use as a reinforcing material because it has excellent impact energy absorption characteristics due to its high ductility as well as excellent corrosion resistance. With the aim of increasing the structural strength of steel shelters, we also conducted an impact test on a shelter fabricated from SS400 deck plates (i.e., steel with improved flexural strength provided by work-hardened trapezoidal corrugated plates). The results show that the shelter could withstand impact with an energy of 13.5 kJ (2.66 kg of simulated ballistic ejecta at 101 m/s on impact). In addition, from the result of the impact test using the roof-simulating structure, it was confirmed the impact absorption energy is further increased when artificial pumice as an additional protective layer is installed on this structure. Observations of the shelter after the impact test show that there is still some allowance for deformation caused by projectile impact, which means that the proposed steel shelter holds promise, not only structurally, but also from the aspects of transportation and assembly. Hence, the usefulness of shelters that use steel was shown experimentally. However, shelter construction should be suitable for the target environment.

scholarly journals Effects of equal channel angular pressing and heat treatments on the microstructures and mechanical properties of selective laser melted and cast AlSi10Mg alloys

2021 ◽  
Vol 21 (3) ◽  
Author(s):  
Przemysław Snopiński ◽  
Mariusz Król ◽  
Marek Pagáč ◽  
Jana Petrů ◽  
Jiří Hajnyš ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Low Temperature ◽  
Equal Channel Angular Pressing ◽  
Heat Treatments ◽  
Electron Backscattered Diffraction ◽  
Angular Pressing ◽  
Low Temperature Annealing ◽  
Transmission Electron ◽  
Before And After ◽  
The Impact

AbstractThis study investigated the impact of the equal channel angular pressing (ECAP) combined with heat treatments on the microstructure and mechanical properties of AlSi10Mg alloys fabricated via selective laser melting (SLM) and gravity casting. Special attention was directed towards determining the effect of post-fabrication heat treatments on the microstructural evolution of AlSi10Mg alloy fabricated using two different routes. Three initial alloy conditions were considered prior to ECAP deformation: (1) as-cast in solution treated (T4) condition, (2) SLM in T4 condition, (3) SLM subjected to low-temperature annealing. Light microscopy, transmission electron microscopy, X-ray diffraction line broadening analysis, and electron backscattered diffraction analysis were used to characterize the microstructures before and after ECAP. The results indicated that SLM followed by low-temperature annealing led to superior mechanical properties, relative to the two other conditions. Microscopic analyses revealed that the partial-cellular structure contributed to strong work hardening. This behavior enhanced the material’s strength because of the enhanced accumulation of geometrically necessary dislocations during ECAP deformation.

scholarly journals Microstructure and Mechanical Properties of Heat-Affected Zone of Repeated Welding AISI 304N Austenitic Stainless Steel by Gleeble Simulator

Metals ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 773
Author(s):  
Y.H. Guo ◽  
Li Lin ◽  
Donghui Zhang ◽  
Lili Liu ◽  
M.K. Lei
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Impact Energy ◽  
Heat Affected Zone ◽  
Ferrite Content ◽  
Equipment Safety ◽  
Microstructure And Mechanical Properties ◽  
Δ Ferrite ◽  
The Impact

Heat-affected zone (HAZ) of welding joints critical to the equipment safety service are commonly repeatedly welded in industries. Thus, the effects of repeated welding up to six times on the microstructure and mechanical properties of HAZ for AISI 304N austenitic stainless steel specimens were investigated by a Gleeble simulator. The temperature field of HAZ was measured by in situ thermocouples. The as-welded and one to five times repeated welding were assigned as-welded (AW) and repeated welding 1–5 times (RW1–RW5), respectively. The austenitic matrices with the δ-ferrite were observed in all specimens by the metallography. The δ-ferrite content was also determined using magnetic and metallography methods. The δ-ferrite had a lathy structure with a content of 0.69–3.13 vol.%. The austenitic grains were equiaxial with an average size of 41.4–47.3 μm. The ultimate tensile strength (UTS) and yield strength (YS) mainly depended on the δ-ferrite content; otherwise, the impact energy mainly depended on both the austenitic grain size and the δ-ferrite content. The UTS of the RW1–RW3 specimens was above 550 MPa following the American Society of Mechanical Engineers (ASME) standard. The impact energy of all specimens was higher than that in ASME standard at about 56 J. The repeated welding up to three times could still meet the requirements for strength and toughness of welding specifications.

scholarly journals Microstructure and Mechanical Properties of Modern 11%Cr Heat-Resistant Steel Weld Joints

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3430
Author(s):  
Grzegorz Golański ◽  
Jacek Słania ◽  
Marek Sroka ◽  
Paweł Wieczorek ◽  
Michał Urzynicok ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Welded Joints ◽  
Martensitic Steel ◽  
Base Material ◽  
Hardness Measurement ◽  
Power Industry ◽  
Strength Properties ◽  
Typical Structure ◽  
Δ Ferrite ◽  
The Impact

In addition to good high-temperature creep resistance and adequate heat resistance, steels for the power industry must have, among other things, good weldability. Weldability of such steels is one of the criteria determining whether or not the material is suitable for applications in the power industry. Therefore, when materials such as martensitic steel Thor 115 (T115) are introduced into the modern power industry, the quality and properties of welded joints must be assessed. The paper presents the results of metallographic and mechanical investigations of T115 martensitic steel welded joints. The analysis was carried out on joints welded with two filler metals: WCrMo91 (No. 1) and EPRI P87 (No. 2). The scope of the investigations included: microstructural investigations carried out using optical, scanning and transmission electron microscopy and mechanical testing, i.e., Vickers microhardness and hardness measurement, static tensile test and impact test. The macro- and microstructural investigations revealed correct structure of the weld, without welding imperfections. The microstructural investigations of joint No. 1 revealed a typical structure of this type of joint, i.e., the martensitic structure with numerous precipitates, while in joint No. 2, the so-called Nernst’s layers and δ-ferrite patches were observed in the weld fusion zone as well as the heat affected zone (HAZ). The mechanical properties of the test joints met the requirements for the base material. A slight influence of the δ-ferrite patch on the strength properties of joint No. 2 was observed, and its negative effect on the impact energy of HAZ was visible.

scholarly journals The Effect of Layers and Bullet Type on Impact Properties of Glass Fibre Reinforced Polymer (GFRP) Using a Single Stage Gas Gun (SSGG)

2014 ◽  
Vol 564 ◽  
pp. 428-433 ◽  
Author(s):  
S.N.A. Safri ◽  
Mohamed Thariq Hameed Sultan ◽  
N. Razali ◽  
Shahnor Basri ◽  
Noorfaizal Yidris ◽  
...  
Keyword(s):  
Impact Energy ◽  
Glass Fibre ◽  
Impact Test ◽  
Single Stage ◽  
Gas Gun ◽  
Reinforced Polymer ◽  
Glass Fibre Reinforced Polymer ◽  
Fibre Reinforced Polymer ◽  
Glass Fibre Reinforced ◽  
The Impact

The purpose of this work is to study the best number of layer with the higher impact energy using Glass Fibre Reinforced Polymer (GFRP). The number of layers used in this study was 25, 33, 41, and 49. The impact test was performed using Single Stage Gas Gun (SSGG) for each layers given above with different bullets such as blunt, hemispherical and conical bullets. The gas gun pressure was set to 5, 10, 15 and 20 bar. All of the signals captured from the impact test were recorded using a ballistic data acquisition system. The correlation between the impact energy in terms of number of layer and type of bullet from this test are presented and discussed. It can be summarise that as the number of layer increases, impact energy also increases. In addition, from the results, it was observed that by using different types of bullets (blunt, hemispherical, conical), there is only a slight difference in values of energy absorbed by the specimen.

Sign in / Sign up

Export Citation Format

Share Document