Using SiO2 Hard Mask for Fabrication of Micro Fresnel Focusing Lens for Ultrasonic Ejectors

2020 ◽  
Vol 863 ◽  
pp. 73-78
Author(s):  
Tuan Anh Bui ◽  
Min Chun Pan ◽  
Tzon Han Wu ◽  
Thanh Long Le
Keyword(s):  
Process Parameters ◽  
Side Wall ◽  
Fresnel Lens ◽  
Sio2 Film ◽  
Hard Mask ◽  
Fabrication Procedure ◽  
Fresnel Lenses ◽  
Wall Profile ◽  
Focusing Lens

The fabrication of Fresnel focusing lenses operating at frequencies of 100 and 200 MHz was investigated in order to enhance the focusing efficiency of ultrasonic energy. The effects of process parameters on the four-level Fresnel lens profiles were discussed to find a most feasible fabrication procedure through these experiments. The quality of Fresnel lenses was improved when two-and three-mask processes using SiO2 film as the hard mask were employed. Besides, a better side-wall profile of Fresnel lens was obtained by using the three-mask process as compared to the two-mask one.

Application Of Cusum Chart In Control Of Paper Quality

GIS Business ◽  
2020 ◽  
Vol 14 (6) ◽  
pp. 1062-1069
Author(s):  
S.Ramesh ◽  
B.A.Vasu
Keyword(s):  
Process Parameters ◽  
Manufacturing Process ◽  
Paper Industry ◽  
Primary Data ◽  
Cusum Chart ◽  
Paper Machine ◽  
Statistical Control ◽  
Operating Characteristics ◽  
Small Shift

This paper is an attempt to assess if the manufacturing process of paper machine is in statistical control thereby improving the quality of paper being produced in a paper industry at the time of process itself. Quality is the foremost criteria for achieving the business target. Therefore, emphasis was made on controlling the quality of paper at the time of manufacturing process itself, rather than checking the finished lots at a later time.  This control on quality will help the industry deduct the small shift in the process parameters and modify the operating characteristics at the time of production itself rather than receiving complaints from customers at a later stage.  This paper describes controlling quality at the time of manufacture itself and helps the industry to concentrate on quality at low cost. The researcher has collected primary data at a leading paper industry during October, 2019.  Though X-bar and Range charges were primarily used, CUSUM charts were used to sense the minor shifts in manufacturing process, to explore the possibility of adjusting process parameters during manufacture of paper.

scholarly journals Effect of Tool Geometry Parameters on the Formability of a Camera Cover in the Deep Drawing Process

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3993
Author(s):  
Thanh Trung Do ◽  
Pham Son Minh ◽  
Nhan Le
Keyword(s):  
Deep Drawing ◽  
Thickness Distribution ◽  
Metal Flow ◽  
Sheet Thickness ◽  
Side Wall ◽  
Tool Geometry ◽  
Drawing Process ◽  
Nose Radius ◽  
Deep Drawing Process

The formability of the drawn part in the deep drawing process depends not only on the material properties, but also on the equipment used, metal flow control and tool parameters. The most common defects can be the thickening, stretching and splitting. However, the optimization of tools including the die and punch parameters leads to a reduction of the defects and improves the quality of the products. In this paper, the formability of the camera cover by aluminum alloy A1050 in the deep drawing process was examined relating to the tool geometry parameters based on numerical and experimental analyses. The results showed that the thickness was the smallest and the stress was the highest at one of the bottom corners where the biaxial stretching was the predominant mode of deformation. The problems of the thickening at the flange area, the stretching at the side wall and the splitting at the bottom corners could be prevented when the tool parameters were optimized that related to the thickness and stress. It was clear that the optimal thickness distribution of the camera cover was obtained by the design of tools with the best values—with the die edge radius 10 times, the pocket radius on the bottom of the die 5 times, and the punch nose radius 2.5 times the sheet thickness. Additionally, the quality of the camera cover was improved with a maximum thinning of 25% experimentally, and it was within the suggested maximum allowable thickness reduction of 45% for various industrial applications after optimizing the tool geometry parameters in the deep drawing process.

scholarly journals Effects of Process Parameters on the Color Quality of Anthocyanin-Based Colorants from Conventional and Microwave-Assisted Aqueous Extraction of Sweet Potato (Ipomoea batatas L.) Leaf Varieties

Proceedings ◽  
2020 ◽  
Vol 70 (1) ◽  
pp. 103
Author(s):  
Jin Mark D. G. Pagulayan ◽  
Aprille Suzette V. Mendoza ◽  
Fredelyn S. Gascon ◽  
Jan Carlo C. Aningat ◽  
Abigail S. Rustia ◽  
...  
Keyword(s):  
Sweet Potato ◽  
Process Parameters ◽  
Ipomoea Batatas ◽  
Extraction Methods ◽  
Aqueous Extraction ◽  
Potato Leaf ◽  
Microwave Assisted ◽  
Color Quality ◽  
The Impact

The study aimed to evaluate the effects of process parameters (time and raw material weight (RMW)) of conventional (boiling for 10–45 min) and microwave-assisted (2–8 min) aqueous extraction on the color quality (i.e., lightness (L*), chroma (C*), and hue (H°) of anthocyanin –based colorants of red and Inubi sweet potato (Ipomoea batatas L.) leaves. Using response surface methodology, it was found that RMW and boiling time (BT) and microwave time (MT) generally had a significant (p < 0.05) effect on the color quality of the extract from both extraction methods. The effects were found to vary depending on the extraction method and variety of the leaves used. Both extraction methods produced a brown to brick-red extract from the Inubi variety that turned red-violet to pink when acidified. The red sweet potato leaves produced a deep violet colored extract that also turned red-violet when acidified. It is recommended that the anthocyanin content of the extracts be measured to validate the impact of the methods on the active agent. Nevertheless, the outcomes in this study may serve as baseline data for further studies on the potential of sweet potato leaf colorants (SPLC) as a colorant with functional properties.

Multi-objective optimization of injection-molded plastic parts using entropy weight, random forest, and genetic algorithm methods

2020 ◽  
Vol 40 (4) ◽  
pp. 360-371
Author(s):  
Yanli Cao ◽  
Xiying Fan ◽  
Yonghuan Guo ◽  
Sai Li ◽  
Haiyue Huang
Keyword(s):  
Genetic Algorithm ◽  
Random Forest ◽  
Regression Model ◽  
Process Parameters ◽  
Multi Objective Optimization ◽  
Entropy Weight ◽  
Multi Objective ◽  
Injection Molded ◽  
Plastic Parts

AbstractThe qualities of injection-molded parts are affected by process parameters. Warpage and volume shrinkage are two typical defects. Moreover, insufficient or excessively large clamping force also affects the quality of parts and the cost of the process. An experiment based on the orthogonal design was conducted to minimize the above defects. Moldflow software was used to simulate the injection process of each experiment. The entropy weight was used to determine the weight of each index, the comprehensive evaluation value was calculated, and multi-objective optimization was transformed into single-objective optimization. A regression model was established by the random forest (RF) algorithm. To further illustrate the reliability and accuracy of the model, back-propagation neural network and kriging models were taken as comparative algorithms. The results showed that the error of RF was the smallest and its performance was the best. Finally, genetic algorithm was used to search for the minimum of the regression model established by RF. The optimal parameters were found to improve the quality of plastic parts and reduce the energy consumption. The plastic parts manufactured by the optimal process parameters showed good quality and met the requirements of production.

scholarly journals Study on the Influence of Surface Temperature Field of Aluminum Alloy Etched by Laser Water Jet Composite Machining

Materials ◽  
2020 ◽  
Vol 13 (14) ◽  
pp. 3206
Author(s):  
Xuehui Chen ◽  
Xin Xu ◽  
Wei Liu ◽  
Lei Huang ◽  
Hao Li ◽  
...  
Keyword(s):  
Aluminum Alloy ◽  
Temperature Field ◽  
Surface Temperature ◽  
Process Parameters ◽  
Water Jet ◽  
Laser Machining ◽  
Material Surface ◽  
Laser Etching ◽  
Surface Temperature Field

This paper studies the compound effect of liquid medium and laser on the workpiece and analyses the law of material surface temperature change during the processing. Taking 7075-T6 aluminum alloy as the research object, the surface temperature field of aluminum alloy processed using water-jet-assisted laser machining under different process parameters was simulated using finite element software. In addition, the temperature field of the material surface was detected in real-time using the self-built water-jet-assisted laser machining temperature field detection system, and the processing results were observed and verified using an optical microscope, scanning electron microscope, and energy spectrum analyzer. The results show that when the water jet inflow angle is 45°, the heat-affected area of the material surface is the smallest, and the cooling effect of the temperature field of the material surface is better. Considering the liquidus melting point of 7075 aluminum alloys, it is concluded that the processing effect is better when the water jet velocity is 14 m·s−1, the laser power is 100 W, and the laser scanning speed is 1.2 mm·s−1. At this time, the quality of the tank is relatively good, there are no cracks in the bottom of the tank, and there is less slag accumulation. Compared with anhydrous laser etching, water-jet-assisted laser etching can reduce the problems of micro-cracks, molten slag, and the formation of a recast layer in laser etching and improve the quality of the workpiece, and the composition of the bottom slag does not change. This study provides theoretical guidance and application support for the selection and optimization of process parameters for water-jet-assisted laser etching of aluminum alloy and further enriches the heat transfer mechanism of multi-field coupling in the process of water-jet-assisted laser machining.

Boring-Rolling Process Research and Tooling Design of Hydraulic Cylinder

2013 ◽  
Vol 842 ◽  
pp. 634-638
Author(s):  
Yan Jing ◽  
Feng Zhao
Keyword(s):  
Process Parameters ◽  
High Efficiency ◽  
Hydraulic Cylinder ◽  
Rolling Process ◽  
Process Research ◽  
Cylinder Block ◽  
Process Route ◽  
Emerging Issues ◽  
Tooling Design

By comparison, this paper determines inner bore processing technic program of the engineering machinery hydraulic cylinder block and makes some analysis of the rolling processing technic and relevant emerging issues to propose reasonable and feasible process route and process parameters and ensure the quality of the cylinder processing. It also shows the design of boring-rolling compound tools with high efficiency and high precision for given cylinders.

A Novel High Concentration Fresnel Lens as a Solar Concentrator

2021 ◽  
pp. 1-29
Author(s):  
Kuldeep Awasthi ◽  
Desireddy Shashidhar Reddy ◽  
Mohd. Kaleem Khan
Keyword(s):  
Optical Axis ◽  
Spherical Aberration ◽  
Spherical Surface ◽  
Fresnel Lens ◽  
High Concentration ◽  
Aperture Diameter ◽  
Convex Lens ◽  
Flat Base ◽  
Fresnel Lenses ◽  
Outer Vertex

Abstract This paper describes the design methodology for a novel Fresnel lens. The original Fresnel lens is obtained from a plano-convex lens, whose spherical surface is split into a number of divisions (called facets), collapsed onto the flat base. Thus, all the facets of the original Fresnel lens have the same radius as that of the plano-convex lens. The proposed design aims to achieve better ray concentration and reduced spherical aberration than the original Fresnel lens by constructing spherical facets with unequal radii. The centers and radii of facets are constrained so that the ray refracted from the bottom vertex of each facet on one side of the optical axis and the ray refracted from the outer vertex of the corresponding facet on the other side of the optical axis must intersect at the focal plane. The proposed lens design has resulted in a 275% gain in the concentration ratio and a 72.5% reduction in the spherical aberration compared to the original lens of the same aperture diameter and number of facets. The performance of both novel and original Fresnel lenses when used as solar concentrators with a conical coil receiver is evaluated. The novel Fresnel lens led to increased heat gain and resulted in a compact solar collector design.

Sign in / Sign up

Export Citation Format

Share Document