Study the Surface and Chip Formation of Wood Materials by Milling Method

2021 ◽  
Vol 1047 ◽  
pp. 74-81
Author(s):  
Nguyen Huu Loc ◽  
Tring Quoc Hung
Keyword(s):  
Experimental Study ◽  
Chip Formation ◽  
Chip Thickness ◽  
Response Surfaces ◽  
Geometrical Parameters ◽  
Milling Cutter ◽  
Milled Surface ◽  
Milling Method ◽  
Working Parameters ◽  
Tip Radius

This paper discusses the experimental study and the mechanism of chip formation, sliding and cutting in processing wood milling surface. The main objective is to determine chip thickness upon the coefficient k and tool tip radius ρ. Technically, when analysing we use FCCCD's second-order response surfaces method and analysis of variance (ANOVA) for determining the coefficient k upon the factors of milling cutter diameter D, the feeding per tooth Sz and tool tip radius ρ. According to the obtained experimental results, we determined the value domain of the machine's working factors so that the cutter tool tip can slide or cut the chip on the milled surface of tropical wood materials. From the coefficient k, we can determine the slide length Lsl which gives reason for the abrasion phenomenon of the front or rear sides of the cutter. The results allow us to choose the geometrical parameters ​​for milling cutter, apart from the working parameters for processing the surface of wood materials with the highest quality as possible.

Investigation of the Dynamics of Microend Milling—Part I: Model Development

2006 ◽  
Vol 128 (4) ◽  
pp. 893-900 ◽  
Author(s):  
Martin B. G. Jun ◽  
Xinyu Liu ◽  
Richard E. DeVor ◽  
Shiv G. Kapoor
Keyword(s):  
Cutting Force ◽  
Chip Formation ◽  
Model Development ◽  
Chip Thickness ◽  
Fault System ◽  
Formation Mechanisms ◽  
Force Model ◽  
Line Field ◽  
Fault Parameters ◽  
Microend Milling

In microend milling, due to the comparable size of the edge radius to chip thickness, chip formation mechanisms are different. Also, the design of microend mills with features of a large shank, taper, and reduced diameter at the cutting edges introduces additional dynamics and faults or errors at the cutting edges. A dynamic microend milling cutting force and vibration model has been developed to investigate the microend milling dynamics caused by the unique mechanisms of chip formation as well as the unique microend mill design and its associated fault system. The chip thickness model has been developed considering the elastic-plastic nature in the ploughing process. A slip-line field modeling approach is taken for a cutting force model development that accounts for variations in the effective rake angle and dead metal cap. The process fault parameters associated with microend mills have been defined and their effects on chip load have been derived. Finally, a dynamic model has been developed considering the effects of both the unique microend mill design and fault system and factors that become significant at high spindle speeds including rotary inertia and gyroscopic moments.

Preliminary Experimental Study on Effect of Cutting Fluid on Milled Surface Quality of Iron-Base Superalloy

2014 ◽  
Vol 1077 ◽  
pp. 61-65
Author(s):  
Pei Yan ◽  
Xiang Su ◽  
Gang Wang ◽  
Yi Ming Rong
Keyword(s):  
Experimental Study ◽  
Surface Quality ◽  
High Speed ◽  
Cutting Fluid ◽  
Cutting Fluids ◽  
Machined Surface ◽  
Iron Base ◽  
Milled Surface ◽  
Base Superalloy

As the development of new materials and high speed machining, cutting fluid becomes more and more important because of its functions of cooling, lubrication, corrosion protection and cleaning. The main purposes of cutting fluid are decreasing temperature, reducing friction, extending tool life and improving machining efficiency. In precision machining, high machined surface integrity is the most important. In this paper, a preliminary experimental study on effect of two different cutting fluids on milled surface quality of iron-base superalloy was taken. The surface morphology, roughness, micro hardness and residual stress of the machined surface were investigated. The results showed that the material properties and geometric characteristics of the machined surface were significantly affected by cutting fluid conditions. The effect of cutting fluid on machined surface quality and service performance will become an important research direction. This paper also suggests the main contents of the further research on effect of cutting fluids on machined surface.

The Role of Grain Tip Radius in Fine Grinding

1975 ◽  
Vol 97 (3) ◽  
pp. 1119-1125 ◽  
Author(s):  
G. K. Lal ◽  
M. C. Shaw
Keyword(s):  
Grain Size ◽  
Surface Finish ◽  
Chip Thickness ◽  
Radius Of Curvature ◽  
Undeformed Chip Thickness ◽  
Fine Grinding ◽  
Abrasive Grains ◽  
Grinding Conditions ◽  
Tip Radius

The scratches produced by single abrasive grains in overcut fly milling show that the transverse shape of a grain is closely approximated by an arc of a circle. This radius of curvature is found to be independent of grain type and grinding conditions but varies with the grain size. The equation for undeformed chip thickness for surface grinding is rederived in terms of this radius. The important role that the transverse curvature of the grain plays relative to surface finish is also discussed.

A Micromilling Experimental Study on AISI 4340 Steel

2009 ◽  
Vol 407-408 ◽  
pp. 335-338 ◽  
Author(s):  
Jin Sheng Wang ◽  
Da Jian Zhao ◽  
Ya Dong Gong
Keyword(s):  
Experimental Study ◽  
Surface Roughness ◽  
Cutting Force ◽  
Spectrum Analysis ◽  
Chip Thickness ◽  
Experimental Results ◽  
Minimum Chip Thickness ◽  
Aisi 4340 Steel ◽  
4340 Steel ◽  
Aisi 4340

A micromilling experimental study on AISI 4340 steel is conducted to understand the micromilling principle deeply. The experimental results, especially on the surface roughness and cutting force, are discussed in detail. It has been found the minimum chip thickness influences the surface roughness and cutting force greatly. Meanwhile, the material elastic recover induces the increase of the axial micromilling force. The average cutting force and its spectrum analysis validate the minimum chip thickness approximation of AISI 4340 is about 0.35μm.

Dynamic Response Analysis in End Milling Using Pretwisted Beam Finite Element

1995 ◽  
Vol 117 (1) ◽  
pp. 1-10 ◽  
Author(s):  
C.-L. Liao ◽  
J.-S. Tsai
Keyword(s):  
Finite Element ◽  
Cutting Force ◽  
Present Model ◽  
End Milling ◽  
Chip Thickness ◽  
Beam Element ◽  
Force Model ◽  
Milling Cutter ◽  
Tool Deflections ◽  
Cutting System

This paper develops an analytical model to estimate the dynamic responses in end milling, i.e., dynamic milling cutter deflections and cutting forces, by using the finite element method along with an adequate end milling cutting force model. The whole cutting system includes spindle, bearings and cutter. The spindle is structurally modeled with the Timoshenko-beam element, the milling cutter with the pretwisted Timoshenko-beam element due to its special geometry, and the bearings with lumped springs and dampers. Because the damping matrix in the resulting finite element equation of motion for the whole cutting system is not of proportional damping due to the presence of bearing damping, we use state-vector approach and convolution integral to find the solution of equations of motion. To assure the accuracy of dynamic response predication, the associated cutting force model should be sufficiently precise. Since the dynamic cutting force is proportional to the chip thickness, a quite accurate algorithm for the calculation of chip thickness variation due to tool geometry, runout and spindle-tool vibration is developed. A number of dynamic cutting forces and tool deflections obtained from the present model for various cutting conditions are compared with the experimental and analytical results available in the literature, and good agreement is demonstrated for these comparisons. Therefore the present model is useful for the prediction of end milling instability. Also, the tool deflections obtained by using the pretwisted beam element are found smaller than those by straight beam elements without pretwist angle. Hence, neglecting the pretwist angle in the structural model of milling cutter may overestimate the tool deflections.

Theoretical Analysis of Serrated Chip Formation Based on Ideal Models in High Speed Cutting

2010 ◽  
Vol 154-155 ◽  
pp. 239-245
Author(s):  
Chong Yang Gao ◽  
Bin Fang ◽  
Yuan Tong Gu
Keyword(s):  
Chip Formation ◽  
High Speed ◽  
Engineering Application ◽  
Chip Thickness ◽  
Chip Morphology ◽  
Formation Model ◽  
Serrated Chip ◽  
Serrated Chip Formation ◽  
Serrated Chips ◽  
The Ideal

In this paper, two ideal formation models of serrated chips, the symmetric formation model and the unilateral right-angle formation model, have been established for the first time. Based on the ideal models and related adiabatic shear theory of serrated chip formation, the theoretical relationship among average tooth pitch, average tooth height and chip thickness are obtained. Further, the theoretical relation of the passivation coefficient of chip’s sawtooth and the chip thickness compression ratio is deduced as well. The comparison between these theoretical prediction curves and experimental data shows good agreement, which well validates the robustness of the ideal chip formation models and the correctness of the theoretical deducing analysis. The proposed ideal models may have provided a simple but effective theoretical basis for succeeding research on serrated chip morphology. Finally, the influences of most principal cutting factors on serrated chip formation are discussed on the basis of a series of finite element simulation results for practical advices of controlling serrated chips in engineering application.

Chip Formation and Force Responses in Linear Rock Cutting: An Experimental Study

2016 ◽  
Vol 139 (1) ◽  
Author(s):  
Demeng Che ◽  
Weizhao Zhang ◽  
Kornel Ehmann
Keyword(s):  
Experimental Study ◽  
Chip Formation ◽  
Oil And Gas ◽  
Cutting Tool ◽  
Polycrystalline Diamond ◽  
Rock Cutting ◽  
Gas Drilling ◽  
Complex Interactions ◽  
On Chip ◽  
Polycrystalline Diamond Compact

Polycrystalline diamond compact (PDC) cutters, as a major cutting tool, have been widely applied in oil and gas drilling processes. The understanding of the complex interactions at the rock and cutter interfaces is essential for the advancement of future drilling technologies; yet, these interactions are still not fully understood. Linear cutting of rock, among all the testing methods, avoids the geometric and process complexities and offers the most straightforward way to reveal the intrinsic mechanisms of rock cutting. Therefore, this paper presents an experimental study of the cutter’s cutting performance and the rock’s failure behaviors on a newly developed linear rock cutting facility. A series of rock cutting tests were designed and performed. The acquired experimental data was analyzed to investigate the influences of process parameters and the rock’s mechanical properties on chip formation and force responses.

Sign in / Sign up

Export Citation Format

Share Document