Performance of a HAWT Rotor with a Modified Blade Configuration

2021 ◽  
Vol 30 (1) ◽  
pp. 201-220
Author(s):  
Tabrej Khan ◽  
Balbir Singh ◽  
Mohamed Thariq Hameed Sultan ◽  
Kamarul Arifin Ahmad

As the world focuses more on clean and green Earth, wind energy plays a significant role. Wind energy is a renewable source of energy that can cope with the ongoing global fossil fuel crisis. The wind energy converters like wind turbines have been studied a lot in terms of design and performance. The current work includes analyzing the output effects of a horizontal axis wind turbine (HAWT) with a modified blade configuration at specific wind speeds. A numerical investigation is carried out using two different numerical software on the chosen airfoil used in blade design validated with the analysis carried out in open-loop wind tunnels. The study is divided into two phases: first, the selected airfoil is tested experimentally and using CFD, and then the findings are compared to those of the University of Illinois Urbana Champaign wind tunnel tests at low Reynolds numbers. The second phase includes the numerical analysis based on the blade element momentum method and non-linear lifting line simulations of modified blade design at high Reynolds number. The numerical results of rotor performance analysis have been compared to existing experimental results. The findings of all numerical investigations agree with those of the experiments. An optimal value of the power coefficient is obtained at a particular tip speed ratio close to the desired value for large wind turbines. For maximum power, this study investigates the optimum pitch angle. The work demonstrated the improved HAWT rotor blade design to produce better aerodynamic lift and thus improve performance.

2021 ◽  
Vol 67 (5) ◽  
pp. 214-222
Author(s):  
Abdulbasit Mohammed ◽  
Hirpa G. Lemu ◽  
Belete Sirahbizu

The design of a windmill rotor is critical for harnessing wind energy. In this work, a study is conducted to optimize the design and performance of a rotor blade that is suitable for low wind conditions. The windmills’ rotor blades are aerodynamically designed based on the SG6043 airfoil and wind speed data at local selected sites. The aerodynamic profile of the rotor blade that can provide a maximum power coefficient, which is the relation between real rotor performance and the available wind energy on a given reference area, was calculated. Different parameters, such as blade shapes, chord distributions, tip speed ratio, geometries set angles, etc., were used to optimize the blade design with the objective of extracting maximum wind power for a water pumping system. Windmill rotor of 10.74 m, 7.34 m, and 6.34 m diameter with three blades were obtained for the selected sites at Abomsa, Metehara, and Ziway in south-east Ethiopia. During the rotary blades performance optimization, blade element momentum (BEM) theory and solving iteration by MATLAB® coding were used.


2021 ◽  
Vol 67 (5) ◽  
pp. 214-222
Author(s):  
Abdulbasit Mohammed ◽  
Hirpa G. Lemu ◽  
Belete Sirahbizu

The design of a windmill rotor is critical for harnessing wind energy. In this work, a study is conducted to optimize the design and performance of a rotor blade that is suitable for low wind conditions. The windmills’ rotor blades are aerodynamically designed based on the SG6043 airfoil and wind speed data at local selected sites. The aerodynamic profile of the rotor blade that can provide a maximum power coefficient, which is the relation between real rotor performance and the available wind energy on a given reference area, was calculated. Different parameters, such as blade shapes, chord distributions, tip speed ratio, geometries set angles, etc., were used to optimize the blade design with the objective of extracting maximum wind power for a water pumping system. Windmill rotor of 10.74 m, 7.34 m, and 6.34 m diameter with three blades were obtained for the selected sites at Abomsa, Metehara, and Ziway in south-east Ethiopia. During the rotary blades performance optimization, blade element momentum (BEM) theory and solving iteration by MATLAB® coding were used.


2021 ◽  
Vol 104 ◽  
pp. 83-88
Author(s):  
Rahmat Wahyudi ◽  
Diniar Mungil Kurniawati ◽  
Alfian Djafar

The potential of wind energy is very abundant but its utilization is still low. The effort to utilize wind energy is to utilize wind energy into electrical energy using wind turbines. Savonius wind turbines have a very simple shape and construction, are inexpensive, and can be used at low wind speeds. This research aims to determine the effect of the slot angle on the slotted blades configuration on the performance produced by Savonius wind turbines. Slot angle variations used are 5o ,10o , and 15o with slotted blades 30% at wind speeds of 2,23 m/s to 4,7 m/s using wind tunnel. The result showed that a small slot angle variation of 5o produced better wind turbine performance compared to a standard blade at low wind speeds and a low tip speed ratio.


2020 ◽  
Vol 143 (1) ◽  
Author(s):  
Alaa S. Hasan ◽  
Mohammed Abousabae ◽  
Abdel Rahman Salem ◽  
Ryoichi S. Amano

Abstract This study presents the rotor blade airfoil analysis of residential-scale wind turbines. On this track, four new airfoils (GOE 447, GOE 446, NACA 6412, and NACA 64(3)-618) characterized by their high lift-to-drag ratios (161.3, 148.7, 142.7, and 136.3, respectively). These new airfoils are used to generate an entire 7 m long blades for three-bladed rotor horizontal axis wind turbine models tested numerically at low, medium, and rated wind speeds of 7.5, 10, and 12.5 m/s, respectively, with a design tip speed ratio of 7. The criterion to judge each model’s performance is power output. Thus, the blades of the model that produce the highest power are selected to undergo a tip modification (winglet) and leading-edge modification (tubercles), seeking power improvement. It is found that the GOE 447 airfoil outperformed the other three airfoils at all tested wind speeds. Thus, it is opted for adding winglets and tubercles. At 12.5 m/s, winglet design produced 5% more power, while tubercles produced 5.5% more power than the GOE 447 baseline design. Furthermore, the computational domain is divided into two regions: rotating (the disc that encloses the rotor) and stationary (the rest of the flow domain). Meanwhile, the numerical model is validated against the experimental velocity measurements. Since Reynolds-averaged Navier–Stokes with k–ω shear stress transport turbulence model can capture the laminar-to-turbulent boundary layer transition, it is used in the 18 simulations of the current work. However, large eddy simulation (LES) can deal successfully with the various scale eddies resulting from the rotor blades and its interactions with the surrounding flow. Thus, the LES was used in the six simulations done at the rated wind speed. LES power output calculation is 7.9% to 11.9% higher than the RANS power output calculation.


Energies ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 6217
Author(s):  
Kehinde A. Adeyeye ◽  
Nelson Ijumba ◽  
Jonathan S. Colton

The design and development of wind turbines in low-wind-speed areas involves several technical and financial challenges related to maximizing conversion efficiency and minimizing cost. Unfortunately, much of the African continent is dominated by low-wind-speed resources. In this study, a multi-parameter optimization method is used to explore the design of a novel Ferris wheel wind turbine (FWT) technology, which has an 800-kW generation capability. We used the tip speed ratio, lift-to-drag ratio and power coefficient to determine the optimal efficiency by varying the number of blades and rim diameters. The capital cost estimates, as affected by rim diameter and the number of blades, are presented. This paper studies FWTs at their rated wind speeds because wind turbines have their maximum performance at the rated wind speeds, and this allows one to observe the effects of changing the rim diameter and the number of blades without the need to consider the location of the turbine. The results show that reducing the number of spokes by half (from 64 to 32) on the four rim diameters studied decreases the efficiency by less than 0.19%, while reducing the acquisition cost by 42%, installation cost by 42% and mass by 28%. Reducing the number of spokes to a quarter (i.e., from 32 to 16) decreases the efficiency by less than 0.31%, reduces the acquisition and installation costs by 36% and 35.5%, respectively, and the mass by 19.2%, of the four rim diameters studied. The reduction of the number of blades has a significant effect on the efficiency and capital cost with varying rim diameters. This paper shows the potential for Ferris-wheel-based wind turbines for low-wind-speed conditions, such as those that prevail in parts of Africa.


Symmetry ◽  
2019 ◽  
Vol 11 (4) ◽  
pp. 456 ◽  
Author(s):  
Md. Sarkar ◽  
Sabariah Julai ◽  
Chong Wen Tong ◽  
Siti Toha

Blade design of the horizontal axis wind turbine (HAWT) is an important parameter that determines the reliability and efficiency of a wind turbine. It is important to optimize the capture of the energy in the wind that can be correlated to the power coefficient ( C p ) of HAWT system. In this paper, nature-inspired algorithms, e.g., ant colony optimization (ACO), artificial bee colony (ABC), and particle swarm optimization (PSO) are used to search for the blade parameters that can give the maximum value of C p for HAWT. The parameters are tip speed ratio, blade radius, lift to drag ratio, solidity ratio, and chord length. The performance of these three algorithms in obtaining the optimal blade design based on the C p are investigated and compared. In addition, an adaptive neuro-fuzzy interface (ANFIS) approach is implemented to predict the C p of wind turbine blades for investigation of algorithm performance based on the coefficient determination (R2) and root mean square error (RMSE). The optimized blade design parameters are validated with experimental results from the National Renewable Energy Laboratory (NREL). It was found that the optimized blade design parameters were obtained using an ABC algorithm with the maximum value power coefficient higher than ACO and PSO. The predicted C p using ANFIS-ABC also outperformed the ANFIS-ACO and ANFIS-PSO. The difference between optimized and predicted is very small which implies the effectiveness of nature-inspired algorithms in this application. In addition, the value of RMSE and R2 of the ABC-ANFIS algorithm were lower (indicating that the result obtained is more accurate) than the ACO and PSO algorithms.


2021 ◽  
pp. 1-28
Author(s):  
Mehmet Numan Kaya ◽  
Faruk Köse ◽  
Oguz Uzol ◽  
Derek Ingham ◽  
Lin Ma ◽  
...  

Abstract The aerodynamic shapes of the blades are still of high importance and various aerodynamic designs have been developed in order to increase the amount of energy production. In this study, a swept horizontal axis wind turbine blade has been optimized to increase the aerodynamic efficiency using the Computational Fluid Dynamics method. To illustrate the technique, a wind turbine with a rotor diameter of 0.94 m has been used as the baseline turbine and the most appropriate swept blade design parameters, namely the sweep start up section, tip displacement and mode of the sweep have been investigated to obtain the maximum power coefficient at the design tip speed ratio. At this stage, a new equation that allows all three swept blade design parameters to be changed independently has been used to design swept blades, and the response surface method has been used to find out the optimum swept blade parameters. According to the results obtained, a significant increase of 4.28% in the power coefficient was achieved at the design tip speed ratio with the new designed optimum swept wind turbine blade. Finally, baseline and optimum swept blades have been compared in terms of power coefficients at different tip speed ratios, force distributions, pressure distributions and tip vortices.


2013 ◽  
Vol 3 (1) ◽  
Author(s):  
Firman Aryanto ◽  
Made Mara ◽  
Made Nuarsa

The wind turbine is a device that converts wind energy into mechanical energy and then converted into electrical energy through a generator. Horizontal axis wind turbines can increase the efficiency to get the maximum power coefficient. One was using the blade numerous. Maximum efisiensi system will increase the number of watts (power) generated so as to obtain a certain number of watts by simply using the number of windmills lessThe object of this research is the performance testing horizontal axis wind turbine with wind speed variation and variation in terms of the number of blade Efisiensi system (𝜂 )  and Tip Speed Ratio (TSR). Research conducted with the wind coming from the source to the Wind Tunnel fan to direct wind. Wind speed is used there are three variations of the 3 m/s, 3.5 m/s, and 4 m/s and varying the amount of blade that is 3, 4, 5 and 6 blade.The results showed that the best 𝜂  values obtained at a maximum wind speed of 4 m / s and the number of blade 5 with a value of 3.07% 𝜂, whereas 𝜂 smallest value obtained at wind speeds of 3 m/s and the number of blade 3 that the value of 0.05% 𝜂. For TSR maximum value at a maximum speed of 4 m/s occurred in the number of blade 5 is equal to λ = 2.11, while the lowest value at wind speeds of 3 m/s resulting in blade number 3 is equal to λ = 1.49.


Author(s):  
A. R. Krishnanunni ◽  
N. Datta ◽  
H. S. Chambhare ◽  
D. Swaroop

Abstract The basic design and blade structural analysis of a 250 W rooftop-mounted horizontal-axis wind turbine for low wind speeds is presented. A simplified non-dimensional design is first undertaken to optimize the aerodynamic performance. The non-dimensional power curve vs. the design tip speed ratio is computed with the open-source wind turbine design software QBlade. SD7062 airfoil is chosen for the blade section; and its aerodynamic efficiency is obtained for various angles of attack using XFLR5. The design process also gives the optimal chord length and pitch distribution, leading to the blade geometry. The 22-month weather data at the site has been analyzed to obtain the best-fit Weibull distribution. The blade sizing is based on the maximum power coefficient before the stall regulation happens. An attempt is made to enhance the power capture by using a concentrator, whose aerodynamic efficacy is analyzed. The blades are fabricated from Glass Fiber Reinforced Plastic, which reduces both weight and cost. The configuration for the laminate is finalized after several bending and tensile tests of five distinct GFRP samples. This is followed by the structural analysis of the blade. The root stresses and tip deflection are analyzed for extreme-wind conditions, along with the free vibration frequencies.


2015 ◽  
Vol 137 (5) ◽  
Author(s):  
Mohamed Ibrahim ◽  
Abdulrahman Alsultan ◽  
Shaohua Shen ◽  
Ryoichi S. Amano

Despite being harvested thousands of years ago, wind energy was neglected during the industrial revolution because of the strong dependence on fossil fuels. However, after the alarming decrease in the fossil fuels reserves, many have drawn their attentions back to a renewable energy technology, especially the wind energy. This paper presents some of the new designs that are being tested, including slotted blades and tubercles design models. The experimental results are used to validate the numerical studies that are being conducted parallel to the experiments for better understanding and more detailed results. The new slotted blade design produced more power compared to the straight blade for lower wind speeds, while the tubercle blades showed better power performance in severe wind conditions and a more steady behavior under unsteady and higher wind velocities.


Sign in / Sign up

Export Citation Format

Share Document