The Combined Effect of Chemical and Structural Factors on Pitting Corrosion Induced by MnS-(Cr, Mn, Al)O Duplex Inclusions

CORROSION ◽  
10.5006/2581 ◽  
2017 ◽  
Vol 74 (3) ◽  
pp. 312-325 ◽  
Author(s):  
Cheng Man ◽  
Chaofang Dong ◽  
Kui Xiao ◽  
Qiang Yu ◽  
Xiaogang Li
Keyword(s):  
Pitting Corrosion ◽  
Selective Dissolution ◽  
Dissolution Mechanism ◽  
Structural Factors ◽  
Metal Interface ◽  
Kelvin Probe ◽  
Force Microscopy ◽  
Atomic Force ◽  
The Individual

In situ atomic force microscopy, scanning Kelvin probe force microscopy, and potential pulse technology were used to study the pitting behavior induced by inclusions in AM355 martensitic stainless steel. The MnS-(Cr, Mn, Al)O duplex inclusion exhibited the highest sensitivity to the pitting corrosion with respect to the individual MnS and (Cr, Mn, Al)O inclusions. When exposed to a solution containing Cl−, the selective dissolution occurred on the sulfide segment of the duplex inclusion, leading to trenching along the oxide part. The dissolution mechanism of MnS segment in the duplex inclusion is similar to the individual MnS inclusion. The Cr depletion in the boundary layer at the inclusion/metal interface promoted the transition from metastable to stable pitting corrosion in the duplex inclusion.

scholarly journals Magnesium-Free Immobilization of DNA Origami Nanostructures at Mica Surfaces for Atomic Force Microscopy

Molecules ◽  
2021 ◽  
Vol 26 (16) ◽  
pp. 4798
Author(s):  
Yang Xin ◽  
Amir Ardalan Zargariantabrizi ◽  
Guido Grundmeier ◽  
Adrian Keller
Keyword(s):  
Atomic Force Microscopy ◽  
Single Molecule ◽  
Pure Water ◽  
Dna Origami ◽  
Force Microscopy ◽  
Atomic Force ◽  
The Individual ◽  
Individual Strategies ◽  
Phosphate Buffered Saline

DNA origami nanostructures (DONs) are promising substrates for the single-molecule investigation of biomolecular reactions and dynamics by in situ atomic force microscopy (AFM). For this, they are typically immobilized on mica substrates by adding millimolar concentrations of Mg2+ ions to the sample solution, which enable the adsorption of the negatively charged DONs at the like-charged mica surface. These non-physiological Mg2+ concentrations, however, present a serious limitation in such experiments as they may interfere with the reactions and processes under investigation. Therefore, we here evaluate three approaches to efficiently immobilize DONs at mica surfaces under essentially Mg2+-free conditions. These approaches rely on the pre-adsorption of different multivalent cations, i.e., Ni2+, poly-l-lysine (PLL), and spermidine (Spdn). DON adsorption is studied in phosphate-buffered saline (PBS) and pure water. In general, Ni2+ shows the worst performance with heavily deformed DONs. For 2D DON triangles, adsorption at PLL- and in particular Spdn-modified mica may outperform even Mg2+-mediated adsorption in terms of surface coverage, depending on the employed solution. For 3D six-helix bundles, less pronounced differences between the individual strategies are observed. Our results provide some general guidance for the immobilization of DONs at mica surfaces under Mg2+-free conditions and may aid future in situ AFM studies.

Experimental investigations into the mechanical properties of the collagen fibril-noncollagenous protein (NCP) interface in antler bone

2010 ◽  
Vol 1274 ◽  
Author(s):  
Fei Hang ◽  
Asa H Barber
Keyword(s):  
Mechanical Properties ◽  
Mechanical Performance ◽  
Collagen Fibrils ◽  
Experimental Investigations ◽  
Shear Stresses ◽  
Structural Hierarchy ◽  
Force Microscopy ◽  
Atomic Force ◽  
The Individual

AbstractAntler is an extraordinary bone tissue that displays significant overall toughness when compared to other bone materials. The origin of this toughness is due to the complex interaction between the nanoscale constituents as well as structural hierarchy in the antler material. Of particular interest is the mechanical performance of the interface between the collagen fibrils and considerably smaller volume of non-collagenous protein (NCP) between these fibrils. This paper directly examines the mechanical properties of isolated volumes of antler using combined in situ atomic force microscopy (AFM)-scanning electron microscopy (SEM) experiments. The antler material at the nanoscale is approximated to a fiber reinforced composite, with composite theory used to evaluate the interfacial shear stresses generated between the individual collagen fibrils and NCP during mechanical loading.

scholarly journals Ultrafine metal-polymer catalysts based on polyconjugated systems for Fisher–Tropsch synthesis

2020 ◽  
Vol 92 (6) ◽  
pp. 977-984
Author(s):  
Mayya V. Kulikova ◽  
Albert B. Kulikov ◽  
Alexey E. Kuz’min ◽  
Anton L. Maximov
Keyword(s):  
Tropsch Synthesis ◽  
X Ray Diffraction ◽  
Fischer Tropsch ◽  
Force Microscopy ◽  
Composite Catalysts ◽  
Fe Catalyst ◽  
Atomic Force ◽  
And Function ◽  
Metal Polymer

AbstractFor previously studied Fischer–Tropsch nanosized Fe catalyst slurries, polymer compounds with or without polyconjugating structures are used as precursors to form the catalyst nanomatrix in situ, and several catalytic experiments and X-ray diffraction and atomic force microscopy measurements are performed. The important and different roles of the paraffin molecules in the slurry medium in the formation and function of composite catalysts with the two types of aforementioned polymer matrices are revealed. In the case of the polyconjugated polymers, the alkanes in the medium are “weakly” coordinated with the metal-polymer composites, which does not affect the effectiveness of the polyconjugated polymers. Otherwise, alkane molecules form a “tight” surface layer around the composite particles, which create transport complications for the reagents and products of Fischer-Tropsch synthesis and, in some cases, can change the course of the in situ catalyst formation.

Atomic force microscopy of in situ deformed nickel thin films

1999 ◽  
Vol 353 (1-2) ◽  
pp. 194-200 ◽  
Author(s):  
C. Coupeau ◽  
J.F. Naud ◽  
F. Cleymand ◽  
P. Goudeau ◽  
J. Grilhé
Keyword(s):  
Thin Films ◽  
Atomic Force Microscopy ◽  
Force Microscopy ◽  
Nickel Thin Films ◽  
Atomic Force

scholarly journals Degradation Mechanism of Porous Metal-Organic Frameworks by In Situ Atomic Force Microscopy

Nanomaterials ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 722
Author(s):  
Ioanna Christodoulou ◽  
Tom Bourguignon ◽  
Xue Li ◽  
Gilles Patriarche ◽  
Christian Serre ◽  
...  
Keyword(s):  
Drug Delivery ◽  
Degradation Mechanism ◽  
Metal Organic Frameworks ◽  
Porous Metal ◽  
Force Microscopy ◽  
Atomic Force ◽  
Metal Organic ◽  
The Media ◽  
Ph Conditions

In recent years, Metal-Organic Frameworks (MOFs) have attracted a growing interest for biomedical applications. The design of MOFs should take into consideration the subtle balance between stability and biodegradability. However, only few studies have focused on the MOFs’ stability in physiological media and their degradation mechanism. Here, we investigate the degradation of mesoporous iron (III) carboxylate MOFs, which are among the most employed MOFs for drug delivery, by a set of complementary methods. In situ AFM allowed monitoring with nanoscale resolution the morphological, dimensional, and mechanical properties of a series of MOFs in phosphate buffer saline and in real time. Depending on the synthetic route, the external surface presented either well-defined crystalline planes or initial defects, which influenced the degradation mechanism of the particles. Moreover, MOF stability was investigated under different pH conditions, from acidic to neutral. Interestingly, despite pronounced erosion, especially at neutral pH, the dimensions of the crystals were unchanged. It was revealed that the external surfaces of MOF crystals rapidly respond to in situ changes of the composition of the media they are in contact with. These observations are of a crucial importance for the design of nanosized MOFs for drug delivery applications.

In Situ Characterization of the Mechanical Behavior of Gecko's Spatulae by Atomic Force Microscopy

2013 ◽  
Vol 22 ◽  
pp. 85-93
Author(s):  
Shuang Yi Liu ◽  
Min Min Tang ◽  
Ai Kah Soh ◽  
Liang Hong
Keyword(s):  
Mechanical Behavior ◽  
Hierarchical Level ◽  
Intrinsic Properties ◽  
In Situ Characterization ◽  
Force Microscopy ◽  
Atomic Force ◽  
Theoretical Predictions ◽  
Multi Mode

In-situ characterization of the mechanical behavior of geckos spatula has been carried out in detail using multi-mode AFM system. Combining successful application of a novel AFM mode, i.e. Harmonix microscopy, the more detail elastic properties of spatula is brought to light. The results obtained show the variation of the mechanical properties on the hierarchical level of a seta, even for the different locations, pad and stalk of the spatula. A model, which has been validated using the existing experimental data and phenomena as well as theoretical predictions for geckos adhesion, crawling and self-cleaning of spatulae, is proposed in this paper. Through contrast of adhesive and craw ability of the gecko on the surfaces with different surface roughness, and measurement of the surface adhesive behaviors of Teflon, the most effective adhesion of the gecko is more dependent on the intrinsic properties of the surface which is adhered.

Sign in / Sign up

Export Citation Format

Share Document