THE FLOODING AFTER DAMAGE OF A WARSHIP WITH COMPLEX INTERNAL COMPARTMENTS – EXPERIMENTS ON A FULLY CONSTRAINED MODEL IN CALM WATER AND REGULAR BEAM SEAS

2021 ◽  
Vol 154 (A2) ◽  
Author(s):  
G J Macfarlane ◽  
M R Renilson ◽  
T Turner
Keyword(s):  
Degrees Of Freedom ◽  
Numerical Code ◽  
Scale Model ◽  
Experimental Program ◽  
Hull Form ◽  
Video Footage ◽  
Unconstrained Model ◽  
Beam Seas ◽  
Calm Water ◽  
Constrained Model

In order to provide data to assist in developing and validating a numerical code to simulate the flooding immediately following damage scale model experiments were conducted on a fully constrained model to investigate the progressive flooding through a complex series of internal compartments within a generic destroyer type hull form. A 3.268 metre long model of a generic destroyer hull form with a simplified, typical internal arrangement was constructed to cover the configuration of greatest interest. A very rapid damage opening scenario was simulated by rupturing a taut membrane covering an opening. The model was instrumented to measure the levels of water and the air pressures in various compartments. In addition, video footage was obtained of the flooding process from both internally and externally of the model. Previous work presented by Macfarlane et al. (2010) showed the results for the unconstrained model. This paper reports on the outcomes from the experimental program where the model was fully constrained in all six degrees of freedom. Firstly, tests were conducted in calm water with damage opening extents ranging from 50% to 100%. When the damage opening was only 50% the rate of rise of water in each of the compartments was only marginally slower than for the 100% damage extent case. Secondly, the test results in calm water were compared against results from tests in regular beam seas. A ‘set-up’ of water inside each of the compartments on the 2nd Deck was found during the wave tests. The result of this is that the mean equilibrium water level in each compartment in the regular beam sea cases is noticeably higher than the equivalent calm water case, particularly for the two compartments on the port side, away from the damage. Finally, analysis of the data from further calm water and beam sea tests suggests that a similar result also occurs when the model is fixed at various non-zero heel angles.

The Flooding After Damage of a Warship with Complex Internal Compartments - Experiments on a Fully Constrained Model in Calm Water and Regular Beam Seas

2012 ◽  
Vol 154 (A2) ◽  
Keyword(s):  
Degrees Of Freedom ◽  
Numerical Code ◽  
Scale Model ◽  
Experimental Program ◽  
Hull Form ◽  
Video Footage ◽  
Unconstrained Model ◽  
Beam Seas ◽  
Calm Water ◽  
Constrained Model

In order to provide data to assist in developing and validating a numerical code to simulate the flooding immediately following damage scale model experiments were conducted on a fully constrained model to investigate the progressive flooding through a complex series of internal compartments within a generic destroyer type hull form. A 3.268 metre long model of a generic destroyer hull form with a simplified, typical internal arrangement was constructed to cover the configuration of greatest interest. A very rapid damage opening scenario was simulated by rupturing a taut membrane covering an opening. The model was instrumented to measure the levels of water and the air pressures in various compartments. In addition, video footage was obtained of the flooding process from both internally and externally of the model. Previous work presented by Macfarlane et al. (2010) showed the results for the unconstrained model. This paper reports on the outcomes from the experimental program where the model was fully constrained in all six degrees of freedom. Firstly, tests were conducted in calm water with damage opening extents ranging from 50% to 100%. When the damage opening was only 50% the rate of rise of water in each of the compartments was only marginally slower than for the 100% damage extent case. Secondly, the test results in calm water were compared against results from tests in regular beam seas. A ‘set-up’ of water inside each of the compartments on the 2nd Deck was found during the wave tests. The result of this is that the mean equilibrium water level in each compartment in the regular beam sea cases is noticeably higher than the equivalent calm water case, particularly for the two compartments on the port side, away from the damage. Finally, analysis of the data from further calm water and beam sea tests suggests that a similar result also occurs when the model is fixed at various non-zero heel angles.

Experimental and numerical analyses of wedge effects on the rooster tail and porpoising phenomenon of a high-speed planing craft in calm water

2019 ◽  
Vol 233 (13) ◽  
pp. 4637-4652 ◽  
Author(s):  
Sayyed Mahdi Sajedi ◽  
Parviz Ghadimi ◽  
Mohammad Sheikholeslami ◽  
Mohammad A Ghassemi
Keyword(s):  
High Speed ◽  
Degrees Of Freedom ◽  
Dimensional Space ◽  
Three Dimensional ◽  
Scale Model ◽  
Test Cases ◽  
Planing Craft ◽  
Calm Water ◽  
Space Discretization ◽  
Good Agreement

This paper presents experimental and numerical investigation of stability and rooster tail of a mono-hull high-speed planing craft with a constant deadrise angle. Initially, a one-fifth scale model was tested in a towing tank, which showed porpoising phenomenon at 8 m/s (equal to the speed of sailing). Subsequently, two wedges of 5 and 10 mm heights, based on the boundary layer calculations, were mounted on the aft section of the planing hull. These wedges were shown to increase the lift at the aft section. These experiments were carried out at different speeds up to 10 m/s in calm water. The experimental results indicated that the installed wedges reduced the trim, drag, and the elapsed time for reaching the hump peak, and also eliminated the porpoising condition. All these test cases were also numerically simulated using Star CCM+ software. The free surface was modeled using the volume of fluid scheme in three-dimensional space. The examined planing craft had two degrees of freedom, and overset mesh technique was used for space discretization. The obtained numerical results were compared with experimental data and good agreement was displayed in the presented comparisons. Ultimately, the effect of the wedge on the rooster tail behind the planing craft was studied. The results of this investigation showed that by decreasing the trim at a constant speed, the height of the generated wake profile (rooster tail) behind the craft decreases, albeit its length increases.

Scale Effect Studies on Hydrodynamic Performance for DTMB 5415 Using CFD

2018 ◽  
Author(s):  
Heng Zhang ◽  
Hang Zhang ◽  
Xuanshu Chen ◽  
Hao Liu ◽  
Xianzhou Wang
Keyword(s):  
Degrees Of Freedom ◽  
Wave Pattern ◽  
Resistance Coefficient ◽  
Body Motion ◽  
Hydrodynamic Performance ◽  
Scale Model ◽  
Ship Motions ◽  
Calm Water ◽  
Unsteady Rans ◽  
Scale Design

Making CFD with the capability of predicting ship scale design performance, rather than relying on scale model tests will help reduce design costs and provide a greater opportunity to develop more energy efficient ship designs. The key objective of this paper is to perform a fully nonlinear unsteady RANS simulation to predict the ship motions and resistance of a full scale DTMB 5415 ship model. The analyses are performed at design speeds, at a certain Fr number, using in-house computational fluid dynamics (CFD) to solve RANS equation coupled with six degrees of freedom (6DOF) solid body motion equations. RANS equations are solved by finite difference method and PISO arithmetic. Computations have been made using structured grid with overset technology. Simulation results shown that the total resistance coefficient in calm water at service speed is predicted by 2.36% error compared to the related towing tank results. The ship resistance for different scale demonstrated that the current in-house CFD model could predict the resistance in a reasonable range of the EFD data. The comparison of flow field for wave pattern for different scale model were analyzed and discussed.

scholarly journals Design and Calibration of a Hall Effect System for Measurement of Six-Degree-of-Freedom Motion within a Stacked Column

Sensors ◽  
2021 ◽  
Vol 21 (11) ◽  
pp. 3740
Author(s):  
Olafur Oddbjornsson ◽  
Panos Kloukinas ◽  
Tansu Gokce ◽  
Kate Bourne ◽  
Tony Horseman ◽  
...  
Keyword(s):  
Hall Effect ◽  
Degrees Of Freedom ◽  
Reactor Core ◽  
Degree Of Freedom ◽  
Life Extension ◽  
Scale Model ◽  
Design Development ◽  
Seismic Safety ◽  
Six Degrees Of Freedom ◽  
Six Degree Of Freedom

This paper presents the design, development and evaluation of a unique non-contact instrumentation system that can accurately measure the interface displacement between two rigid components in six degrees of freedom. The system was developed to allow measurement of the relative displacements between interfaces within a stacked column of brick-like components, with an accuracy of 0.05 mm and 0.1 degrees. The columns comprised up to 14 components, with each component being a scale model of a graphite brick within an Advanced Gas-cooled Reactor core. A set of 585 of these columns makes up the Multi Layer Array, which was designed to investigate the response of the reactor core to seismic inputs, with excitation levels up to 1 g from 0 to 100 Hz. The nature of the application required a compact and robust design capable of accurately recording fully coupled motion in all six degrees of freedom during dynamic testing. The novel design implemented 12 Hall effect sensors with a calibration procedure based on system identification techniques. The measurement uncertainty was ±0.050 mm for displacement and ±0.052 degrees for rotation, and the system can tolerate loss of data from two sensors with the uncertainly increasing to only 0.061 mm in translation and 0.088 degrees in rotation. The system has been deployed in a research programme that has enabled EDF to present seismic safety cases to the Office for Nuclear Regulation, resulting in life extension approvals for several reactors. The measurement system developed could be readily applied to other situations where the imposed level of stress at the interface causes negligible material strain, and accurate non-contact six-degree-of-freedom interface measurement is required.

Development and Assessment of a Total Resistance Optimized Bow for the AE 36

1994 ◽  
Vol 31 (02) ◽  
pp. 149-160
Author(s):  
Donald C. Wyatt ◽  
Peter A. Chang
Keyword(s):  
Experimental Data ◽  
Optimization Procedure ◽  
Wave Resistance ◽  
Scale Model ◽  
Optimization Approach ◽  
Nonlinear Constraints ◽  
Total Resistance ◽  
Hull Form ◽  
Final Design ◽  
Resistance Data

A numerically optimized bow design is developed to reduce the total resistance of a 23 000 ton ammunition ship (AE 36) at a speed of 22 knots. An optimization approach using slender-ship theory for the prediction of wave resistance is developed and applied. The new optimization procedure is an improvement over previous optimization methodologies in that it allows the use of nonlinear constraints which assure that the final design remains within practical limits from construction and operational perspectives. Analytic predictions indicate that the AE 36 optimized with this procedure will achieve a 40% reduction in wave resistance and a 33% reduction in total resistance at 22 knots relative to a Kracht elliptical bulb bow design. The optimization success is assessed by the analysis of 25th scale model resistance data collected at the David Taylor Research Center deepwater towing basin. The experimental data indicate that the optimized hull form yields a 51% reduction in wave resistance and a 12% reduction in total resistance for the vessel at 22 knots relative to the Kracht bulb bow design. Similarly encouraging results are also observed when comparisons are made with data collected on two other conventionally designed AE 36 designs.

A Nonlinear Mathematical Model for Ship Turning Circle Simulation in Waves

2005 ◽  
Vol 49 (02) ◽  
pp. 69-79 ◽  
Author(s):  
Ming-Chung Fang ◽  
Jhih-Hong Luo ◽  
Ming-Ling Lee
Keyword(s):  
Mathematical Model ◽  
Degrees Of Freedom ◽  
Regular Waves ◽  
Nonlinear Mathematical Model ◽  
Ship Maneuvering ◽  
Sea Trial ◽  
Six Degrees Of Freedom ◽  
Strip Theory ◽  
Calm Water ◽  
Maneuvering Motion

In the paper, a simplified six degrees of freedom mathematical model encompassing calm water maneuvering and traditional seakeeping theories is developed to simulate the ship turning circle test in regular waves. A coordinate system called the horizontal body axes system is used to present equations of maneuvering motion in waves. All corresponding hydrodynamic forces and coefficients for seakeeping are time varying and calculated by strip theory. For simplification, the added mass and damping coefficients are calculated using the constant draft but vary with encounter frequency. The nonlinear mathematical model developed here is successful in simulating the turning circle of a containership in sea trial conditions and can be extended to make the further simulation for the ship maneuvering under control in waves. Manuscript received at SNAME headquarters February 19, 2003; revised manuscript received January 27, 2004.

Experimental Investigation of Hydrodynamic Coefficients of a Wave-Piercing Tumblehome Hull Form

2007 ◽  
Author(s):  
Christopher C. Bassler ◽  
Jason B. Carneal ◽  
Paisan Atsavapranee
Keyword(s):  
Experimental Investigation ◽  
System Modeling ◽  
Flow Simulation ◽  
Roll Damping ◽  
Hull Form ◽  
Damping Coefficients ◽  
Calm Water ◽  
Forced Roll ◽  
Future Work ◽  
Damping Model

A systematic series of calm-water forced roll model tests were performed over a range of forward speeds using an advanced tumblehome hull form (DTMB model #5613-1) to examine the mechanisms of roll damping. This experimental investigation is part of an ongoing effort to advance the capability to assess seakeeping, maneuvering, and dynamic stability characteristics of an advanced surface combatant. The experiment was performed to provide data for development and validation of a semi-empirical roll damping model for use in validation of ship motion and viscous flow simulation codes, as well as to provide a basis for future work with additional experiments, contributing to the development of an improved analytical roll damping model. Two hull configurations were tested: barehull with skeg, and bare hull with skeg and bilge keels. Measurements of forces and moments were obtained over a range of forward speeds, roll frequencies, and roll amplitudes. Stereo particle-image velocimetry (SPIV) measurments were also taken for both zero and forward speeds. Test data was used to calculate added mass/inertia and damping coefficients. Two different system modeling techniques were used. The first method modeled the system as an equivalent linearly-damped second-order harmonic oscillator with the time-varying total stiffness coefficient considered linear. The second technique used equivalent linear damping, including higher-order Fourier components, and a non-linear stiffness formulation. Results are shown, including plots of added inertia and damping coefficients as functions of roll frequency, roll amplitude, and forward speed and SPIV measurements. Trends from the experimental data are compared to results from traditional component roll damping formulations for conventional hull from geometries and differences are discussed.

Multi Vessel Interaction in Shallow Water

2009 ◽  
Author(s):  
Hans Fabricius Hansen ◽  
Stefan Carstensen ◽  
Erik Damgaard Christensen ◽  
Jens Kirkegaard
Keyword(s):  
Shallow Water ◽  
Wave Model ◽  
Irregular Waves ◽  
Numerical Code ◽  
Scale Model ◽  
Hydrodynamic Characteristics ◽  
Mooring Line ◽  
Industry Standard ◽  
Physical Scale ◽  
The Time Domain

A numerical package for simulating vessel motions in the time domain, WAMSIM, is extended to handle multiple moving bodies interconnected through a nonlinear mooring system. WAMSIM relies on the industry standard program WAMIT to calculate the hydrodynamic characteristics and interaction of multiple bodies in the frequency domain. The numerical code is used to simulate the motions and mooring line and fender forces of two LNG tankers moored side-by-side in shallow water. One of the gas tankers is moored to the sea floor through a turret with chain catenaries. Realistic short-crested irregular waves obtained from a Boussinesq wave model are used to force the model. Motion spectra of the simulated motions are compared to measured motions from physical scale model tests. The model shows good agreement with measured motions and mooring line forces.

Model Tests of a Caisson in Wet Towing for Assessing Resistance and Stability in Calm Water and Waves

2018 ◽  
Vol 140 (5) ◽  
Author(s):  
Chang-Wook Park ◽  
Jeonghwa Seo ◽  
Shin Hyung Rhee
Keyword(s):  
Degrees Of Freedom ◽  
Model Tests ◽  
Added Resistance ◽  
Power Requirement ◽  
Effective Power ◽  
Six Degrees Of Freedom ◽  
Calm Water ◽  
Improved Stability ◽  
Scale Ratio ◽  
The Stability

A series of model tests of a caisson in wet towing were conducted in a towing tank to assess the stability and effective power requirement in calm water and head sea conditions. The scale ratio of the model was 1/30, and the model-length-based Froude number in the tests ranged from 0.061 to 0.122, which is equivalent to 2 and 4 knots in the full scale, respectively. During the towing of the model, tension on the towline and six-degrees-of-freedom (6DOF) motion of the model were measured. Under the calm water condition, the effects of towing speed, draft, and initial trim variation on the towing stability and effective power were investigated. Initial trim improved stability and reduced required towing power. In head seas, effective power and towing stability were changed with the wavelength. It increased as the wavelength became longer, but the added resistance in long waves also stabilized the model with reduced yaw motion.

Manoeuvring Study of a Container Ship in Shallow Water Waves

2018 ◽  
Author(s):  
Manases Tello Ruiz ◽  
Marc Mansuy ◽  
Guillaume Delefortrie ◽  
Marc Vantorre
Keyword(s):  
Shallow Water ◽  
Water Waves ◽  
Numerical Study ◽  
Scale Model ◽  
Wave Forces ◽  
Shallow Water Waves ◽  
The North ◽  
Captive Model Tests ◽  
Calm Water ◽  
Large Container

When approaching or leaving a port a ship often needs to perform manoeuvres in the presence of waves. At the same time the water depth is still limited for deep drafted vessels. For manoeuvring simulation purposes this requires a manoeuvring model which includes phenomena such as short crested waves and squat effects. The present paper addresses the manoeuvring problem in shallow water waves numerically and experimentally. The numerical study is conducted by means of potential theory, incorporating first and second order exciting wave forces, and their superposition to the calm water manoeuvring models. The applicability of such an approach is also investigated. The experimental work has been conducted at Flanders Hydraulics Research (in cooperation with Ghent University) with a scale model of an ultra large container vessel. Captive model tests comprise harmonic yaw tests and steady straight line tests with and without waves, at different forward speeds, wave frequencies and amplitudes, in head and following waves. Waves are chosen to represent conditions commonly met by ships in the Belgian coastal zone of the North Sea.

Sign in / Sign up

Export Citation Format

Share Document