scholarly journals Numerical Study on Extent of Hazardous Area for Sonic Jet Release Using Equivalent Leak Diameter

2021 ◽  
Vol 21 (4) ◽  
pp. 121-127
Author(s):  
Seung-Ho Choi ◽  
Hyoung Gwon Choi

In this study, three-dimensional K - E turbulence numerical simulations were conducted to analyze the extent of hazardous area for the sonic jet leakage of flammable gas. Incompressible fluid flows were simulated based on an inlet boundary condition estimated using the theory of “equivalent leak diameter” to prevent the direct simulation of sonic flows near the leakage hole. Numerical simulations of 20 methane leakage scenarios providing the lower explosive limit contour showed shapes of the hazardous area with a maximum height of approximately 12-14 times larger than the maximum width, owing to convection. The extents of hazardous area determined using computational fluid dynamics (CFD) were approximately 5%-10% lower than the results obtained with 1 m over based on IEC 60079-10-1. For scenarios in which quantitative data were not calculated using IEC 60079-10-1 due to low release rates, CFD provided quantitative data for the extent of hazardous area, showing nonlinear relationships with the pressure and diameter of leak holes.

2010 ◽  
Vol 6 (S274) ◽  
pp. 429-432
Author(s):  
Matteo Bocchi ◽  
Jerry P. Chittenden ◽  
Andrea Ciardi ◽  
Francisco Suzuki-Vidal ◽  
Gareth N. Hall ◽  
...  

AbstractWith the aim to model jets produced by conical wire arrays on the MAGPIE generator, and to strengthen the link between laboratory and astrophysical jets, we performed three-dimensional magneto-hydro-dynamic numerical simulations using the code GORGON and successfully reproduced the experiments. We found that a minimum resolution of ~100 μm is required to retrieve the unstable character of the jet. Moreover, arrays with less wires produce more unstable jets with stronger magnetic fields around them.


2014 ◽  
Vol 6 ◽  
pp. 565061 ◽  
Author(s):  
Zhi-Jun Shuai ◽  
Wan-You Li ◽  
Xiang-Yuan Zhang ◽  
Chen-Xing Jiang ◽  
Feng-Chen Li

Flow induced vibration due to the dynamics of rotor-stator interaction in an axial-flow pump is one of the most damaging vibration sources to the pump components, attached pipelines, and equipment. Three-dimensional unsteady numerical simulations were conducted on the complex turbulent flow field in an axial-flow water pump, in order to investigate the flow induced vibration problem. The shear stress transport (SST) k-ω model was employed in the numerical simulations. The fast Fourier transform technique was adopted to process the obtained fluctuating pressure signals. The characteristics of pressure fluctuations acting on the impeller were then investigated. The spectra of pressure fluctuations were predicted. The dominant frequencies at the locations of impeller inlet, impeller outlet, and impeller blade surface are all 198 Hz (4 times of the rotation frequency 49.5 Hz), which indicates that the dominant frequency is in good agreement with the blade passing frequency (BPF). The first BPF dominates the frequency spectrum for all monitoring locations inside the pump.


Author(s):  
Sotirios S. Sarakinos ◽  
Georgios N. Lygidakis ◽  
Ioannis K. Nikolos

In this study an academic CFD code, named Galatea-I, is presented, capable for simulating inviscid, viscous laminar and viscous turbulent incompressible fluid flows. It employs the RANS (Reynolds-Averaged Navier-Stokes) approach along with the SST (Shear Stress Transport) turbulence model to predict turbulent flow phenomena, such as recirculations and separations of flow, on three-dimensional unstructured hybrid grids, composed of prismatic, tetrahedral and pyramidal elements. Discretization of the governing equations is obtained with a node-centered finite-volume scheme. Parallel processing and agglomeration multigrid scheme are implemented for the acceleration of the numerical process. As the title of this paper reveals, the solver is validated against the test cases of the DARPA SUBOFF program; in particular, flows over the SUBOFF bare hull submarine geometry at two incident angles and the SUBOFF hull with fairwater configuration are examined. The obtained results, compared to available in open literature experimental data as well as results computed by reference solvers, indicate the proposed methodology’s potential to accurately simulate complex fluid flows.


Water ◽  
2020 ◽  
Vol 12 (4) ◽  
pp. 935 ◽  
Author(s):  
Giovanni Cannata ◽  
Federica Palleschi ◽  
Benedetta Iele ◽  
Francesco Cioffi

In this paper we propose a three-dimensional numerical study of the coastal currents produced by the wave motion in the area opposite the Cetraro harbour (Italy), during the most significant wave event for the coastal sediment transport. The aim of the present study is the characterization of the current patterns responsible for the siltation that affects the harbour entrance area and the assessment of a project solution designed to limit this phenomenon. The numerical simulations are carried out by a three-dimensional non-hydrostatic model that is based on the Navier–Stokes equations expressed in integral and contravariant form on a time-dependent curvilinear coordinate system, in which the vertical coordinate moves in order to follow the free surface variations. The numerical simulations are carried out in two different geometric configurations: a present configuration, that reproduces the geometry of the coastal defence structures currently present in the harbour area and a project configuration, which reproduces the presence of a breakwater designed to modify the coastal currents in the area opposite the harbour entrance.


2019 ◽  
Vol 396 ◽  
pp. 177-186
Author(s):  
Vinicius da Rosa Pepe ◽  
Luiz Alberto Oliveira Rocha ◽  
Flavia Schwarz Franceschini Zinani ◽  
Antonio Ferreira Miguel

This article presents the results of flows in "T" shaped duct bifurcations. The problem is to find the resistance to flow in three-dimensional (3D) structures with different homothetic relationships between sizes (diameters and lengths) of parent and daughter ducts. The method used is the Constructal Design, which is based on the Constructal Theory. The minimization of the global resistance to flow, subjected to geometric constraints of volume and area occupied by the ducts, is the key to search for optimum configurations. The flows investigated were three-dimensional, laminar, incompressible, in steady state, with uniform and constant properties. The results obtained numerically were verified via comparison with analytical results available in the literature. In this work, ranges of length and ratio of diameterss from 0.5 to 1 and 0.1 to 1, respectively, were investigated, for Reynolds numbers equal to 102 and 103. The main results indicate that the T-shaped structure with impermeable walls, agree with Hess-Murray's law.


2003 ◽  
Vol 21 (3) ◽  
pp. 327-334 ◽  
Author(s):  
D. KARTOON ◽  
D. ORON ◽  
L. ARAZI ◽  
D. SHVARTS

The three-dimensional (3D) turbulent mixing zone (TMZ) evolution under Rayleigh–Taylor and Richtmyer–Meshkov conditions was studied using two approaches. First, an extensive numerical study was made, investigating the growth of a random 3D perturbation in a wide range of density ratios. Following that, a new 3D statistical model was developed, similar to the previously developed two-dimensional (2D) statistical model, assuming binary interactions between bubbles that are growing at a 3D asymptotic velocity. Confirmation of the theoretical model was gained by detailed comparison of the bubble size distribution to the numerical simulations, enabled by a new analysis scheme that was applied to the 3D simulations. In addition, the results for the growth rate of the 3D bubble front obtained from the theoretical model show very good agreement with both the experimental and the 3D simulation results. A simple 3D drag–buoyancy model is also presented and compared with the results of the simulations and the experiments with good agreement. Its extension to the spike-front evolution, made by assuming the spikes' motion is governed by the single-mode evolution determined by the dominant bubbles, is in good agreement with the experiments and the 3D simulations. The good agreement between the 3D theoretical models, the 3D numerical simulations, and the experimental results, together with the clear differences between the 2D and the 3D results, suggest that the discrepancies between the experiments and the previously developed models are due to geometrical effects.


1994 ◽  
Vol 273 ◽  
pp. 1-29 ◽  
Author(s):  
Peter Bartello ◽  
Olivier Métais ◽  
Marcel Lesieur

Numerical simulations investigating the formation and stability of quasi-two-dimensional coherent vortices in rotating homogeneous three-dimensional flow are described. In a numerical study of shear flows Lesieur, Yanase & Métais (1991) found that cyclones (respectively anticyclones) with |ω2D| ∼ O(2Ω), where ω2D is the vorticity and Ω is the rotation rate, are stabilized (respectively destabilized) by the rotation. A study of triply periodic pseudo-spectral simulations (643) was undertaken in order to investigate the vorticity asymmetry in homogeneous turbulence. Specifically, we examine (i) the possible three-dimensionalization of initially two-dimensional vortices and (ii) the emergence of quasi-two-dimensional structures in initially-isotropic three-dimensional turbulence. Direct numerical simulations of the Navier—Stokes equations are compared with large-eddy simulations employing a subgridscale model based on the second-order velocity structure function evaluated at the grid separation and with simulations employing hyperviscosity.Isolated coherent two-dimensional vortices, obtained from a two-dimensional decay simulation, were superposed with a low-amplitude three-dimensional perturbation, and used to initialize the first set of simulations. With Ω = 0, a three-dimensionalization of all vortices was observed. This occurred first in the small scales in conjunction with the formation of longitudinal hairpin vortices with vorticity perpendicular to that of the initial quasi-two-dimensional flow. In agreement with centrifugal stability arguments, when 2Ω = [ω2D]rms a rapid destabilization of anticyclones was observed to occur, whereas the initial two-dimensional cyclonic vortices persisted throughout the simulation. At larger Ω, both cyclones and anticyclones remained two-dimensional, consistent with the Taylor—Proudman theorem. A second set of simulations starting from isotropic three-dimensional fields was initialized by allowing a random velocity field to evolve (Ω = 0) until maximum energy dissipation. When the simulations were continued with 2Ω = [ω · Ω]rms/Ω, the three-dimensional flow was observed to organize into two-dimensional cyclonic vortices. At larger Ω, two-dimensional anticyclones also emerged from the initially-isotropic flow. The consequences for a variety of industrial and geophysical applications are clear. For quasi-two-dimensional eddies whose characteristic circulation times are of the order ofder of Ω−1, rotation induces a complete disruption of anticyclonic vortices, while stabilizing cyclonic ones.


2015 ◽  
Vol 724 ◽  
pp. 275-278
Author(s):  
Tao Yong Zhou ◽  
Bin Hu ◽  
Ping Xu ◽  
Bo Yan

The tamping maintenance of railway ballast is employed to restore the geometry of railway track distorted by train traffics. In this paper, based on the analysis of tamping principle, the three dimensional analysis model of railway ballast is created using the discrete element method, numerical simulations are performed to study the micro mechanical behavior of railway ballast under tamping operation. This paper presents the evolution of force chains inside railway ballast under tamping operation. The obtained results are showed that the contact force inside railway ballast is enhanced by tamping, so as to improve the carrying capacity and stability of railway track.


Energies ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 606
Author(s):  
Seoeum Han ◽  
Sangyoon Lee ◽  
Bok Jik Lee

This numerical study was conducted to investigate the flow properties in a model scramjet configuration of the experiment in the T4 shock tunnel. In most numerical simulations of flows in shock tunnels, the inflow conditions in the test section are determined by assuming the thermal equilibrium of the gas. To define the inflow conditions in the test section, the numerical simulation of the nozzle flow with the given nozzle reservoir conditions from the experiment is conducted by a thermochemical nonequilibrium computational fluid dynamics (CFD) solver. Both two-dimensional (2D) and three-dimensional (3D) numerical simulations of the flow in a model scramjet were conducted without fuel injection. Simulations were performed for two types of inflow conditions: one for thermochemical nonequilibrium states obtained from the present nozzle simulation and the other for the data available using the thermal equilibrium and chemical nonequilibrium assumptions. The four results demonstrate the significance of the modelling approach for choosing between 2D or 3D, and thermal equilibrium or nonequilibrium.


Sign in / Sign up

Export Citation Format

Share Document