Optimization of Injection Molding of Automotive Plastic Horn Cover Part Using Taguchi Method and Reverse Engineering

The aim of the paper consisted in the development of an injection mold for plastic horn cover parts in commercial vehicles. Three mold types were designed in anticipation of the structure and quality of molds, and injection molding numerical analyses were conducted for the three types of molds. One mold type was selected in consideration of the resin flow patterns inside the mold, surface quality, and final deflection amount of the horn cover. To perform optimal injection molding using the selected mold, optimization of injection molding parameters was performed using the Taguchi method, one of the designs of experiment (DOE) and ANOVA methods. As a result, it was confirmed that the deflection amount of the molding under optimal molding parameters decreased by about 34.3% compared to the deflection amount before optimization of the molding parameters. Based on these encouraging results, the previously selected mold type was actually manufactured. The horn cover was molded using the obtained optimal injection molding parameters to the manufactured mold. To verify the precision of the molded horn cover, the deflection amount of the molding was measured with a 3D scanner. The deflection amount of the horn cover was estimated to be about 11% to 43% larger for each measurement position than the deflection amounts in the analysis results. The manufactured mold was revised to solve the problem that the deflection amount of the actual molding is larger than the deflection amount predicted by injection molding analysis. The dimensions and surface quality of the horn cover with a revised mold were satisfactory.

Adaptive Conformal Cooling of Injection Molds Using Additively Manufactured TPMS Structures

In injection molding, cooling channels are usually manufactured with a straight shape, and thus have low cooling efficiency for a curved mold. Recently, additive manufacturing (AM) was used to fabricate conformal cooling channels that could maintain a consistent distance from the curved surface of the mold. Because this conformal cooling channel was designed to obtain a uniform temperature on the mold surface, it could not efficiently cool locally heated regions (hot spots). This study developed an adaptive conformal cooling method that supports localized-yet-uniform cooling for the heated region by employing micro-cellular cooling structures instead of the typical cooling channels. An injection molding simulation was conducted to predict the locally heated region, and a mold core was designed to include a triply periodic minimal surface (TPMS) structure near the heated region. Two biomimetic TPMS structures, Schwarz-diamond and gyroid structures, were designed and fabricated using a digital light processing (DLP)-type polymer AM process. Various design parameters of the TPMS structures, the TPMS shapes and base coordinates, were investigated in terms of the conformal cooling performance. The mold core with the best TPMS design was fabricated using a powder-bed fusion (PBF)-type metal AM process, and injection molding experiments were conducted using the additively manufactured mold core. The developed mold with TPMS cooling achieved a 15 s cooling time to satisfy the dimensional tolerance, which corresponds to a 40% reduction in comparison with that of the conventional cooling (25 s).

Comparison of the Flow Field in a Slab Continuous Casting Mold between the Thicknesses of 180 mm and 250 mm by High Temperature Quantitative Measurement and Numerical Simulation

In the present work, the flow field in a slab continuous casting mold with thicknesses of 180 and 250 mm are compared using high temperature quantitative measurement and numerical simulation. The results of the numerical simulation are in agreement with those of the high temperature quantitative measurement, which verifies the accuracy and reliability of the numerical simulation. Under the same working conditions, the velocities near the mold surface with the thickness of 180 mm were slightly higher than those of the mold with the thickness of 250 mm. The flow pattern in the 180 mm thick mold maintains DRF more easily than that in 250 mm thick mold. The kinetic energy of the jet dissipates faster in the 250 mm thick mold than in the 180 mm mold. For double-roll flow (DRF), as the argon gas bubbles can be flushed into the deeper region under the influence of strong jets on both sides, the argon bubbles distribute widely in the mold. For single-roll flow (SRF), as the argon bubbles float up quickly after leaving the side holes, the bubble distribution is more concentrated in the width direction, which may cause violent interface fluctuation and slag entrainment. The fluctuation at the steel-slag interface in the mold with 180 mm thickness is greater than that in the mold with 250 mm thickness but less than 5 mm. The increase of mold thickness may lead to a decrease of the symmetry of the flow field in the thickness direction and uniformity of mold powder layer thickness. In summary, the steel throughput should be increased in the 250 mm thick mold compared with that in the 180 mm thick mold.

Numerical Simulation and Process Optimization of a 3D Thin-Walled Polymeric Part Using Injection Compression Molding

Injection compression molding (ICM) is a hybrid injection molding process for manufacturing polymer products with high precision and surface accuracy. In this study, a 3D flow simulation was employed for ICM and injection molding (IM) processes. Initially, the process parameters of IM and ICM were discussed based on the numerical simulations. The IM and ICM processes were compared via numerical simulation by using CAE tools of Moldflow software. The effect of process parameters of mold surface temperature, melting temperature, compression force and injection time on clamping force and pressure at the injection location of molded 3D BJ998MO Polypropylene (MFI 100) part was investigated by Taguchi analysis. In conclusion, it was found that the ICM has a relatively lower filling pressure than ICM, which results in reduced clamping force for producing a 3D thin-walled polymeric part.

The Relationship between a Defined Microstructure within the Mold Surface and the Corresponding Roughness on the Part: A Systematic Study on Particle Size, Filler-, and Compatibilizer Content

The perception of a surface and its haptic properties are significantly influenced by roughness and microstructure, respectively, whereby non-negligible parameters include friction, contact area, temperature, and humidity between the human finger and the examined surface. In particular, for a scientific investigation on haptic influences, the production of samples with a defined surface roughness is indispensable. The aim of this study is to analyze the impact of various mold insert roughnesses combined with the influences of particle size, filler-, and compatibilizer content on impression quality. An unfilled high density polyethylene was chosen as a reference for the impression quality investigations, while fillers with significantly different particle sizes and a compatibilizer were used to produce proprietary compounds. Injection molded parts were manufactured utilizing mold inserts with three different line roughness values. To support the obtained results, a multivariate analysis of variance, a simulation of the filling phase as well as a rheological material characterization were conducted. The results revealed that (i) the impression quality can be independent of the applied insert roughness based on the filler particle size that was studied, (ii) an increasing on both filler particle size and compatibilizer content raise the sample roughness as a function of the penetration ability of the filler into the insert valleys, and (iii) with a higher insert roughness, the thermoplastic moldings generally exhibit a significantly smoother topography. An assumed correlation between part roughness and melt viscosity could not be confirmed.

Evaluating the Application of Heating Conductor Surfaces Inside Plasma Sprayed Coatings in Permanent Mold Metal Casting Processes for Local, Near-Surface Heat Release

With casting being a complex process which involves several physical effects and interactions, a wide array of means for influencing such processes exist. Here, the liquid–solid phase change is of utmost importance, as it is a deciding factor for a part’s final properties. Especially with today’s high critical material property requirements, control of the solidification process is indispensable. For the most part, the cooling of a casting defines its solidification. What determines the cooling process is the heat balance of the system. The foundry industry has been using different approaches for influencing the heat balance for a long time. The application of different kinds of coatings with either insulating or heat transfer promoting properties as well as temperature control via cooling channels inside the mold is widely used. Progress in the field of plasma spraying of coatings and the application of heating conductor surfaces have rendered a new concept possible: The integration of heating conductors inside a coating allows for the release of heat in closest vicinity of the melt–mold interface. This paper depicts the use of numerical simulations to investigate the local application of heating conductor layers inside the mold surface coating for a permanent mold casting process and discusses concepts for influencing the heat balance that would not be possible with state-of-the-art cooling channel approaches.

Effect of Femtosecond-Laser-Structured Injection Molding Tool on Mechanical Properties of the Manufactured Product

During the injection molding process, the melt travels with a flow due to friction. As the velocity of the layers next to the wall is less than that of those flowing in the middle of the channel, a fountain flow is formed at the melt front. The temperature of the polymer surface decreases from the melt temperature to the contact temperature after contacting the mold surface. Based on all this, a complex shell–core structure is formed in injection-molded products, which can be influenced by the processing parameters and the surface of the tool insert. This paper focuses on investigating the effect of the microstructures replicated from the insert to the polymer product on its mechanical properties. During the research, two microstructured surfaces were created, with different effects on the melt flow formed by the femtosecond laser. These were compared with a ground insert to analyze the effects. For examining the effect of technological variables on the mechanical properties, an experimental design was used. The structure created by the femtosecond laser on the surface of the tool influenced the mechanical properties of the polymer products. Recognizing the effect of microstructures on the melt front and, through this, the change in mechanical properties, a predefined polymer product property can be achieved.

Effect of acoustic excitation on fiber-reinforced polypropylene and the influence on melt viscosity

The paper describes a novel technological approach to influencing the rheological properties of thermoplastic materials exposed to acoustic energy. The flow behavior of polypropylene with different mass percentages of glass fibers is investigated in a parallel plate rheometer under high-frequency longitudinal excitation. The influence of oscillation frequency on the melt viscosity is explained by means of shear thinning criteria. The dependence of the oscillation shape using sinusoidal excitation on shear thinning as a function of different fiber reinforcement percentages is also investigated. A phenomenological view describes the mutually influencing parameters with regard to different material compositions and different excitation frequencies over the time course of the rheometric measurement. Interacting relationships are analyzed and discussed and the potential of the actuator system to influence the plastic melt is worked out. Based on this, a technological approach follows which describes the transfer of an oscillating mold surface to plastics processing methods, which, especially in the case of energy-intensive injection molding technology, leads to the expectation of possible resource efficiency in energy and material.

Interfacial Interactions during Demolding in Nanoimprint Lithography

Nanoimprint lithography (NIL) is a useful technique for the fabrication of nano/micro-structured materials. This article reviews NIL in the field of demolding processes and is divided into four parts. The first part introduces the NIL technologies for pattern replication with polymer resists (e.g., thermal and UV-NIL). The second part reviews the process simulation during resist filling and demolding. The third and fourth parts discuss in detail the difficulties in demolding, particularly interfacial forces between mold (template) and resist, during NIL which limit its capability for practical commercial applications. The origins of large demolding forces (adhesion and friction forces), such as differences in the thermal expansion coefficients (CTEs) between the template and the imprinted resist, or volumetric shrinkage of the UV-curable polymer during curing, are also illustrated accordingly. The plausible solutions for easing interfacial interactions and optimizing demolding procedures, including exploring new resist materials, employing imprint mold surface modifications (e.g., ALD-assisted conformal layer covering imprint mold), and finetuning NIL process conditions, are presented. These approaches effectively reduce the interfacial demolding forces and thus lead to a lower defect rate of pattern transfer. The objective of this review is to provide insights to alleviate difficulties in demolding and to meet the stringent requirements regarding defect control for industrial manufacturing while at the same time maximizing the throughput of the nanoimprint technique.