The Structural Effect of Electrode Mesh on Hydrogen Evolution Reaction Performance for Alkaline Water Electrolysis

Alkaline water electrolysis (AWE) is a mature water electrolysis technology that can produce green hydrogen most economically. This is mainly attributed to the use of Ni-based materials that are easy to process and inexpensive. The nickel-based meshes with various structures such as woven mesh and expanded mesh are widely used as electrode in the AWE due to its common availability and easy fabrication. However, the morphological effect of meshes on hydrogen evolution reaction (HER) performance has not been studied. Here a new parameter to determine the structural effect of mesh on HER performance was first proposed. The key factors of the parameter were found to be the strand width, pore width and the strand surface area. The woven mesh with the ratio of pore width to strand width that converges to 1 showed the lowest the overpotential. The expanded mesh with the higher the structural surface area exhibited the lowest the overpotential. This study will help to choose an optimal structure for the mesh with the HER electrode.

Structural and Dynamical Behaviour of Colloids with Competing Interactions Confined in Slit Pores

Systems with short-range attractive and long-range repulsive interactions can form periodic modulated phases at low temperatures, such as cluster-crystal, hexagonal, lamellar and bicontinuous gyroid phases. These periodic microphases should be stable regardless of the physical origin of the interactions. However, they have not yet been experimentally observed in colloidal systems, where, in principle, the interactions can be tuned by modifying the colloidal solution. Our goal is to investigate whether the formation of some of these periodic microphases can be promoted by confinement in narrow slit pores. By performing simulations of a simple model with competing interactions, we find that both the cluster-crystal and lamellar phases can be stable up to higher temperatures than in the bulk system, whereas the hexagonal phase is destabilised at temperatures somewhat lower than in bulk. Besides, we observed that the internal ordering of the lamellar phase can be modified by changing the pore width. Interestingly, for sufficiently wide pores to host three lamellae, there is a range of temperatures for which the two lamellae close to the walls are internally ordered, whereas the one at the centre of the pore remains internally disordered. We also find that particle diffusion under confinement exhibits a complex dependence with the pore width and with the density, obtaining larger and smaller values of the diffusion coefficient than in the corresponding bulk system.

Tailoring α/β Ratio of Pollen-Like Anhydrous Lactose as Ingredient Carriers for Controlled Dissolution Rate

Lactose is a commonly used excipient with two isomers. Different isomers have different properties, especially in terms of solubility. This work is mainly to explore the influence of different a/β ratio lactose on drug dissolution. This work has developed novel mesoporous pollen-like lactose anhydrous with tailored α/β ratios as ingredient carriers for controlled dissolution rate. The produced lactose carriers are pollen-like with a particle size of ~15 μm and a mean pore width of ~30 nm. β-lactose anhydrous has a unique FTIR-peak at 948 cm−1, whereas α-lactose anhydrous shows a unique FTIR-peak at 855 cm−1. DSC analysis suggests that the pollen-like α/β-lactose crystals are polymorphs with unique peaks of melting points. XRD analysis suggests that (5:5)α/β-lactose polymorph has high crystalline purity. The loading efficiency (30.6–33.4% w/w) of acetamidophenol within the nanoporous lactose particles is dependent on the surface structure and pore volumes—the pore volumes were found to be 0.0209–0.0380 cm3/g. The release rates of acetamidophenol are lower for lactose with high α/β ratios. The lactose solubility and the first-order release constant can be tailored by changing the proportion of β-lactose in the pollen-like lactose carriers.

Porous Lactose as a Novel Ingredient Carrier for the Improvement of Quercetin Solubility In Vitro

In this work, quercetin was loaded in the highly-porous lactose via the adsorption of quercetin molecules in ethanol. The method aims to improve the quercetin solubility and the loading capacity of lactose. The method relates to the synthesis of the highly-porous lactose with a particle size of ∼35 μm, a mean pore width of ∼30 nm, a BET surface area of 35.0561 ± 0.4613 m2/g, and a BJH pore volume of ∼0.075346 cc/g. After the quercetin loading in ethanol, BET surface area and BJH pore volume of porous lactose were reduced to 28.8735 ± 0.3526 m2/g and 0.073315 cc/g, respectively. The reduction rate was based on the quercetin loading efficiency of highly-porous lactose. DSC analysis and XRD analysis suggest that the sediments of quercetin in the nanopores of porous lactose are crystalline. FTIR spectroscopy results suggest that there is no significant interaction between quercetin and lactose. The highly-porous lactose had a higher loading efficiency of 20.3% (w/w) compared to the α-lactose (with 5.2% w/w). The release rates of quercetin from the highly-porous lactose tablets were faster compared to the conventional α-lactose carrier.

Fractal Properties of Pore Distribution of Electrospun Nanofiber Membrane

Due to the complex and chaotic characteristics of elecrtospun nanofiber membrane, fractal theory is a suitable mathematical framework. Using the fractal theory, Matlab and other computer software in Mathematics, the fractal properties of pore distribution of elecrtospun nanofiber membrane and the relationship between the fractal dimension and the physical properties of nonwovens are studied. Thirty samples were produced by using polyvinyl alcohol (PVA)on the DXES-01 automatic electrostatic spinning machine; BMP images of 30 samples were obtained by TM-1000 table scanning electron microscope; The scanning electron micro-scope images were grayed by digital image processing technology, and the average pore width of the samples was further calculated by Matlab software from the gray value matrix; G-P algorithm is used to calculate the fractal dimension of pore width distribution; The relationship between air flow resistance and the fractal dimension of pore width distribution of electrospun nanofiber membrane was analyzed. Finally, the correlation fractal dimension of the average pore width of electrospun nanofiber membrane has a quadratic function relation with the air flow resistance; The correlation fractal dimension of the average pore width obtained is consistent with the fractal dimension of porosity obtained by Ting Wang under the meaning of the relative error less than 10%is the same.

The role of contact angle and pore width on pore condensation and freezing

It has recently been shown that pore condensation and freezing (PCF) is a mechanism responsible for ice formation under cirrus cloud conditions. PCF is defined as the condensation of liquid water in narrow capillaries below water saturation due to the inverse Kelvin effect, followed by either heterogeneous or homogeneous nucleation depending on the temperature regime and presence of an ice-nucleating active site. By using sol–gel synthesized silica with well-defined pore diameters, morphology and distinct chemical surface-functionalization, the role of the water–silica contact angle and pore width on PCF is investigated. We find that for the pore diameters (2.2–9.2 nm) and water contact angles (15–78∘) covered in this study, our results reveal that the water contact angle plays an important role in predicting the humidity required for pore filling, while the pore diameter determines the ability of pore water to freeze. For T>235 K and below water saturation, pore diameters and water contact angles were not able to predict the freezing ability of the particles, suggesting an absence of active sites; thus ice nucleation did not proceed via a PCF mechanism. Rather, the ice-nucleating ability of the particles depended solely on chemical functionalization. Therefore, parameterizations for the ice-nucleating abilities of particles in cirrus conditions should differ from parameterizations at mixed-phase clouds conditions. Our results support PCF as the atmospherically relevant ice nucleation mechanism below water saturation when porous surfaces are encountered in the troposphere.

Evaluation of Dissolved Organic Matter Removal Characteristics in GAC Adsorption Process in Drinking Water Treatment Process using LC-OCD-OND

Objectives:In this study, we used liquid chromatograph-organic carbon detector-organic nitrogen detector (LC-OCD-OND) to evaluate adsorption and breakthrough characteristics of NOM fractions (biopolymers (BP), humic substances (HS), building blocks (BB) and low molecular weight organic substances (LMW-O)) according to the various characteristics of the different materials of granular activated carbons (GACs).Methods:Breakthrough characteristics, adsorption capacity and partition coefficients were evaluated by NOM fractions (BP, HS, BB, and LMW-O) using a lab-scale GAC adsorption column filled with coal-, coconut- and wood-based GAC. The GAC column test was operated with 10 minutes empty bed contact time (EBCT). The pore characteristics of each GAC were evaluated using an automated gas sorption analyzer (Autosorb iQ3, Quantachrome, USA) and the concentrations of NOM fractions in the influent and effluent were analyzed using chromatography LC-OCD-OND (Model 8, DOC-Labor, Germany).Results and Discussion:NOM adsorption capacity was evaluated for different materials of laboratory scale GAC adsorption column test. To study the adsorption behavior of individual NOM fractions according to the operation time, NOM was fractionated into BP, HS, BB and LMW-O by LC-OCD-OND, and the individual NOM fractions were quantified. Higher MW like BP was not adsorbed to GAC, in contrast, HS, BB, and LMW-O were well removed during the initial operation period, the concentrations in the effluent gradually increased as increase the operation period until reaching to the pseudo steady-state. Poor removal of BP in GAC adsorption may be a result of blocking the pores with large MW BP and hinder the access to the pores. However, in the case of HS, BB, and LMW-O, as the molecular size decreased, these organic matters easily access to the pores inside of GAC. It was confirmed through the partition coefficient that the adsorption capacity of these NOM fractions increased in proportion to the MW. In addition, in order to achieve a high NOM removal efficiency in the GAC adsorption process, not only the specific surface area, pore volume, and pore width of the GAC must be large, but also the pH_zpc must be higher than the neutral pH level.Conclusions:In order to achieve a high NOM removal efficiency in the GAC adsorption process, not only the specific surface area, pore volume, and pore width of the GAC must be large, but also the pH_zpc must be higher than the neutral pH level. In addition, in the NOM fractions, BP were not adsorbed to GAC, while the adsorption capacity of the remaining NOM fractions increased as the MW of the NOM fractions decreased. LMW-O was the most adsorbed, followed by BB, HS and BP. BP and HS play an important role in the membrane fouling that are introduced a lot into domestic and foreign water treatment plants. This study showed that the BP was not removed by the adsorption mechanism of the GAC process. In addition, HS was adsorbed and removed at the beginning of the operation, but the adsorption capacity of HS decreased rapidly as the operation period increased compared to other NOM fractions. Therefore, the GAC adsorption process is not expected to be an effective pre-treatment technology for reducing membrane foulants. Previous studies showed that the yields of DBPs (µmol･DBP/µmol･C) in the high MW humic and low MW non-humic fractions are similar. Therefore, it is suggested that the GAC adsorption process is more effective for DBP precursor control in water containing a larger percentage of LMW NOM.

Translocation of flexible and tensioned ssDNA through in silico designed hydrophobic nanopores with two constrictions

ABSTRACTProtein-inspired nanopores with hydrophobic constriction regions have previously been shown to offer some promise for DNA sequencing. Here we explore a series of pores with two hydrophobic constrictions. The impact of nanopore radius, the nature of residues that define the constriction region and the flexibility of the ssDNA is explored. Our results show that aromatic residues slow down DNA translocation, and in the case of short DNA strands, they cause deviations from a linear DNA conformation. When DNA is under tension, translocation is once again slower when aromatic residues are present in the constriction. However, the lack of flexibility in the DNA backbone provides a narrower window of opportunity for the DNA bases to be retained inside the pore via interaction with the aromatic residues, compared to more flexible strands. Consequently, there is more variability in translocation rates for strands under tension. DNA entry into the pores is correlated to pore width, but no such correlation between width and translocation rate is observed.