Aerodynamic Design, Analysis and Validation of a Small Blended-Wing-Body Unmanned Aerial Vehicle

This paper describes the aerodynamic design and assessment of a blended-wing–body (BWB) configuration under the distributed electric propulsion (DEP) installation constraints. The aerodynamic design rationale and process is described, as well as how the DEP system is considered and simplified in the optimization design process. Both the BWB configuration and the DEP induced effects are numerically simulated and analyzed using the Reynolds Averaged Navier–Stokes (RANS) computational fluid dynamics (CFD) flow solvers. To further demonstrate the feasibility and reliability of the design approach, the wind tunnel tests of a scaled model of the designed BWB configuration are carried out, and both the aerodynamic characteristics and the BWB surface flow are measured and analyzed. The results indicate the reliability and feasibility of the optimization design method introduced in this paper.

Computational analysis and design of an aerofoil with morphing tail for improved aerodynamic performance in transonic regime

This article focuses on the aerodynamic design of a morphing aerofoil at cruise conditions using computational fluid dynamics (CFD). The morphing aerofoil has been analysed at a Mach number of 0.8 and Reynolds number of $3 \times 10^{6}$ , which represents the transonic cruise speed of a commercial aircraft. In this research, the NACA0012 aerofoil has been identified as the baseline aerofoil where the analysis has been performed under steady conditions at a range of angles of attack between $0^{^{\kern1pt\circ}}$ and $3.86^{^{\kern1pt\circ}}$ . The performance of the baseline case has been compared to the morphing aerofoil for different morphing deflections ( $w_{te}/c = [0.005 - 0.1]$ ) and start of the morphing locations ( $x_{s}/c = [0.65 - 0.80]$ ). Further, the location of the shock wave on the upper surface has also been investigated due to concerns about the structural integrity of the morphing part of the aerofoil. Based upon this investigation, a most favourable morphed geometry has been presented that offers both, a significant increase in the lift-to-drag ratio against its un-morphed counterpart and has a shock location upstream of the start of the morphing part.

Aerodynamic design, analysis, and validation techniques for the Tianwen-1 entry module

The clear differences between the atmosphere of Mars and the Earth coupled with the lack of a domestic research basis were significant challenges for the aerodynamic prediction and verification of Tianwen-1. In addition, the Mars entry, descent, and landing (EDL) mission led to specific requirements for the accuracy of the aerodynamic deceleration performance, stability, aerothermal heating, and various complex aerodynamic coupling problems of the entry module. This study analyzes the key and difficult aerodynamic and aerothermodynamic problems related to the Mars EDL process. Then, the study process and results of the design and optimization of the entry module configuration are presented along with the calculations and experiments used to obtain the aerodynamic and aerothermodynamic characteristics in the Martian atmosphere. In addition, the simulation and verification of the low-frequency free oscillation characteristics under a large separation flow are described, and some special aerodynamic coupling problems such as the aeroelastic buffeting response of the trim tab are discussed. Finally, the atmospheric parameters and aerodynamic characteristics obtained from the flight data of the Tianwen-1 entry module are compared with the design data. The data obtained from the aerodynamic design, analysis, and verification of the Tianwen-1 entry module all meet the engineering requirements. In particular, the flight data results for the atmospheric parameters, trim angles of attack, and trim axial forces are within the envelopes of the prediction deviation zones.

Performance and operability of an electrically driven propulsor

This manuscript discusses the operation of an electrically driven fan for a hybrid-electric propulsion system for BAe-146 aircraft. The thrust requirement is fed into an integrated cycle and aerodynamic design tool for the sizing of a ducted fan as one of the main propulsors, podded under the wing as a replacement for a turbofan engine. The electric motor design is initiated with the torque and speed requirements and with the dimensional constraints arising from the driven fan geometry. The fan operation and aerodynamic design are derived by changing the fan pressure ratio and hub-to-tip ratio to obtain a 2-D design space. Surface-mounted permanent magnet electric motor designs are mapped on the 2-D fan design space. The design and operational flexibility of the system is investigated through three scenarios. In the first scenario, the aircraft rate of climb is changed to downsize the electric motor. In the second scenario, the electric motor rated frequency is changed to increase the power density and in the third scenario the electric motor current density is changed for the same purpose. The investigated three scenarios provide design and operational guidelines for reducing the weight of the electric motor for a direct drive application.

Aerodynamic Design and Strength Analysis of the Wing for the Purpose of Assessing the Influence of the Bell-Shaped Lift Distribution

This article deals with aerodynamic and structural calculations of several wing designs to compare the influence of the shape on the lift distribution. Various shapes of wings for the required lift and bending moment were optimized to minimize drag and thereby reduce fuel consumption. One example was a wing with a bell-shaped lift distribution, which was proposed by Ludwig Prandtl and has been forgotten over the years. The first part of the paper focuses on minimization of the wing drag coefficient by a low fidelity method and the results are compared with the CFD calculation with good agreement. In the structural part of the analysis, the inner layout of the studied wings was designed. The structural design, containing elementary wing components and optimization loop, was carried out to minimize weight with respect to panel buckling. From these calculations the weights of wings were obtained and compared. In the last part of this study, an analysis of flight performance of an airplane with presented wings was performed for a selected flight mission. Results indicated that, for the free optimized wing, the fuel saving was about six percent.