adhesive systems
Recently Published Documents


TOTAL DOCUMENTS

1101
(FIVE YEARS 218)

H-INDEX

44
(FIVE YEARS 8)

2022 ◽  
Vol 8 ◽  
Author(s):  
Sebastian Dahle ◽  
Kavyashree Srinivasa ◽  
Jure Žigon ◽  
Arnaud Maxime Cheumani Yona ◽  
Georg Avramidis ◽  
...  

The use of wood-based materials in building and construction is constantly increasing as environmental aspects and sustainability gain importance. For structural applications, however, there are many examples where hybrid material systems are needed to fulfil the specific mechanical requirements of the individual application. In particular, metal reinforcements are a common solution to enhance the mechanical properties of a wooden structural element. Metal-reinforced wood components further help to reduce cross-sectional sizes of load-bearing structures, improve the attachment of masonry or other materials, enhance the seismic safety and tremor dissipation capacity, as well as the durability of the structural elements in highly humid environments and under high permanent mechanical load. A critical factor to achieve these benefits, however, is the mechanical joint between the different material classes, namely the wood and metal parts. Currently, this joint is formed using epoxy or polyurethane (PU) adhesives, the former yielding highest mechanical strengths, whereas the latter presents a compromise between mechanical and economical constraints. Regarding sustainability and economic viability, the utilization of different adhesive systems would be preferable, whereas mechanical stabilities yielded for metal-wood joints do not permit for the use of other common adhesive systems in such structural applications. This study extends previous research on the use of non-thermal air plasma pretreatments for the formation of wood-metal joints. The plasma treatments of Norway spruce [Picea abies (L.) Karst.] wood and anodized (E6/EV1) aluminum AlMgSi0.5 (6060) F22 were optimized, using water contact angle measurements to determine the effect and homogeneity of plasma treatments. The adhesive bond strengths of plasma-pretreated and untreated specimens were tested with commercial 2-component epoxy, PU, melamine-urea formaldehyde (MUF), polyvinyl acetate (PVAc), and construction adhesive glue systems. The influence of plasma treatments on the mechanical performance of the compounds was evaluated for one selected glue system via bending strength tests. The impact of the hybrid interface between metal and wood was isolated for the tests by using five-layer laminates from three wood lamellae enclosing two aluminum plates, thereby excluding the influence of congeneric wood-wood bonds. The effect of the plasma treatments is discussed based on the chemical and physical modifications of the substrates and the respective interaction mechanisms with the glue systems.


Author(s):  
Mario Felipe GUTIÉRREZ ◽  
Luisa F. ALEGRÍA-ACEVEDO ◽  
Alejandra NÚÑEZ ◽  
Luján MÉNDEZ-BAUER ◽  
Romina ÑAUPARI-VILLASANTE ◽  
...  

2021 ◽  
Vol 15 (1) ◽  
pp. 734-741
Author(s):  
Sara Valizadeh ◽  
Elham Farhadi ◽  
Aida Moradi ◽  
Sedighe S. Hashemikamangar

Introduction: Currently, non-thermal plasma is used to modify the enamel and dentin surfaces to improve the bonding surface to dental composite resins. Non-thermal plasma creates a hydrophilic surface, decreases the contact angle, and improves the bonding quality. The present study aimed to evaluate the microshear bond strength (µSBS) of composite resins to dentin using different adhesive systems. Materials and Methods: Bovine incisor teeth were randomly assigned to three groups of G-Premio, Clearfil SE Bond, and Adper Single Bond adhesive groups after preparation. Each group was divided into two subgroups in terms of argon plasma surface preparation, and each subgroup was divided into two groups in terms of thermocycling (n=12). The microshear bond strength of the samples was determined using a universal testing machine. Three-way ANOVA was used to analyze the effect of the adhesive, plasma preparation, and thermocycling. Post hoc Tukey tests were used for two-by-two comparisons of µSBS. Statistical significance was set at P <0.05. Results: The results of the µSBS test showed that the application of plasma resulted in a significant increase in the mean µSBS in the G-Premio group, with no significant increase in the Clearfil SE bond and Adper Single groups. The effect of thermocycling after plasma application was significant only in the Adper Single group. Conclusion: The application of plasma might increase the bond strength of composite resins to dentin. However, further studies are necessary.


Author(s):  
Deborah Cavalcante Magalhães ROLIM ◽  
Lidiane Costa de SOUZA ◽  
Viviane HASS ◽  
Paulo Goberlânio Barros SILVA ◽  
Cácia SIGNORI ◽  
...  
Keyword(s):  

Forests ◽  
2021 ◽  
Vol 12 (12) ◽  
pp. 1672
Author(s):  
Hannes Stolze ◽  
Mathias Schuh ◽  
Sebastian Kegel ◽  
Connor Fürkötter-Ziegenbein ◽  
Christian Brischke ◽  
...  

In this study, varying ambient climates were simulated in a test building by changing temperature and relative humidity. Beech glued laminated timber (glulam, Fagus sylvatica, L.) was freshly installed in the test building and monitoring of the change in wood moisture content of the glulam resulting from the variations in climate was carried out. Subsequently, finger-jointed beech specimens were exposed to the variations in relative humidity measured in the course of the monitoring experiment on a laboratory scale, and thus an alternating climate regime was derived from the conditions in the test building. Its influence on the delamination of the finger-joints was evaluated. In addition, it was examined whether beech finger-joints using commercial adhesive systems fulfil the normative requirements for delamination resistance according to EN 301 (2018) and whether different bonding-wood moisture levels have an effect on the delamination of the finger-joints. In the context of the monitoring experiment, there was a clear moisture gradient in the beech glulam between the inner and near-surface wood. The applied adhesive systems showed almost the same delamination resistance after variation of relative humidity. The normative requirements were met by all PRF-bonded and by most PUR-bonded beech finger-joints with higher bonding wood moisture content.


Polymers ◽  
2021 ◽  
Vol 13 (23) ◽  
pp. 4086
Author(s):  
Diogo Gonçalves ◽  
João Moura Bordado ◽  
Ana C. Marques ◽  
Rui Galhano dos Santos

There is a strong need to develop and implement appropriate alternatives to replace formaldehyde-based adhesive systems, such as phenol–formaldehyde, in the industry of wood-based panels (WBPs). This is due to the toxicity and volatility of formaldehyde and restrictions on its use associated with some formaldehyde-based adhesives. Additionally, the current pressure to reduce the dependence on polymeric materials, including adhesives, from petrochemical-based sources has led to increased interest in bio-based adhesives, which, in some cases, already provide acceptable properties to the end-product. Among the potential raw materials for good-quality, renewable-based adhesive formulations, this paper highlights tannins, lignin, and protein sources. However, regarding renewable sources, specific features must be considered, such as their lower reactivity than certain petrochemical-based sources and, therefore, higher production costs, resource availability issues, and the need for toxicological investigations on alternative systems, to compare them to conventional systems. As a result, further research is highly encouraged to develop viable formaldehyde-free adhesive systems based on renewable sources, either at the technical or economical level. Moreover, herein, we also showcase the present market of WBPs, highlighting the obstacles that the alternative and new bio-based adhesives must overcome.


Sign in / Sign up

Export Citation Format

Share Document