Photoelectric and magnetic properties of chemically synthesized Cd-Ni Ferrite nanomagnetic particles

Cadmium nickel (Cd-Ni) ferrite samples have been successfully synthesized via chemical co-precipitation technique. The structural analysis revealed the formation of FCC framework and Fe-phase in a trivalent state. The crystallite size is decreased with increasing Cd2+ ion composition whereas the lattice constant is increased. SEM was used to obtain the surface morphology and average grain size of the microstructure. The FTIR shows the formation of metal oxide, hydroxyl and carboxylic groups. EDX revealed the formation of Ni2+, Cd2+, Fe3+, and O2- ions in proper stoichiometric composition. Large optical losses were revealed by Cd2+ poor-NiFe2O4 samples whereas Cd2+ rich-CdxNi1-xFe2O4 samples revealed low optical losses and showed enhanced photoconductivity and photoelectric effect. Result from optical analysis showed that Cd2+ rich-CdxNi1-xFe2O4 nanoparticles can be used as infrared (IR) detector, ultraviolet (UV) filter and in optoelectronics device applications. VSM measurement showed an increase in saturation magnetization and decrease in coercivity as Cd2+ ion content is increased. The remanance magnetization and magnetic anisotropy were also examined. Photoluminescence (PL) spectroscopy examined the nature of the light emission of the samples at the excitation wavelength 380 nm and emission of series of colours such as red, green, yellow, orange and violet light at different wavelengths were found.

Numerical Analysis of Micro-Lens Array to the Mid-IR Range

New interferometric IR techniques have recently been developed to allow Sun-Jupiter-like detections in deep space. These techniques demand a high angular resolution, a high sensitivity towards signal detection buried in noise, and a well-defined bandwidth of spectral resolution. Micro-lens arrangements have helped increase the use of these parameters for IR detectors. In this paper we present a finite element method (FEM)-based simulation of a typical micro-lens array, to be used in mid-IR cameras, where the aperture geometry and radius of curvature are varied for design optimization. Moreover, we show the spot and optical aberrations produced by two types of geometrical arrangements. This procedure could be helpful in improving the IR detector signal in the exoplanets exploration, in systems placed outside of the earth’s atmosphere.

P Pemanfaatan Arduino Uno sebagai Alat Ukur Offset Voltage pada Infra Red Detector type TO39 dengan pembanding alat ukur DMM

The infrared detector (or IR detector) is an optoelectronic component and represents the core element of gas analyzers, flame sensors, devices of spectral analysis, as well as non-contact temperature measurement. pyroelectric infrared detectors work with stabilization time in a wide operating temperature range (-55 ... 85) °C, capable of measuring the slightest amounts of infrared radiation (as little as a fraction of a nW) with wavelengths between 1 µm and > 25 µm. The difference of the good pyroelectric or No good (NG) devices shown by graph of voltage offset operating that can check by manual using Digital Multi Meter or semi auto by using microcontroller One of importance measuring of IRD sensors is Offset Voltage, stabilization of offset voltage indicate the sensor is stable with certain level value. Stabilization value measurement during measuring time means the average value not so much different with fluctuation value. 10 bit ADC on Atmega 328 that main microcontroller on Arduino Uno is capable to measure the Offset Voltage of IRD sensor and check the measurement values is within specification of IRD sensor.

ACQUISITION AND PROCESSING CONSIDERATIONS FOR INFRARED IMAGES OF ROTATING TURBINE BLADES

As designers aim to increase efficiency in gas turbines for aircraft propulsion and power generation, spatially-resolved experimental measurements are needed to validate computational models and compare improvement gains of new cooling designs. Infrared (IR) thermography is one such method for obtaining spatially-resolved temperature measurements. As technological advances in thermal detectors enable faster integration times, surface temperature measurements of rotating turbine blades become possible to capture including the smallest features. This paper outlines opportunities enabled by the latest IR detector technologies for capturing spatially-resolved rotating blade temperatures, while also addressing some of the challenges of implementing IR for turbine rigs such as the one in the Steady Thermal Aero Research Turbine (START) Laboratory. This paper documents critical steps in achieving accurate measurements including calibration, integration times, spatial noise, and motion blur. From these results, recommendations are provided for achieving accurate IR measurements collected in a rotating turbine facility to study film cooling.

Thermoelectrically-Cooled InAs/GaSb Type-II Superlattice Detectors as an Alternative to HgCdTe in a Real-Time Mid-Infrared Backscattering Spectroscopy System

We report on the development of thermoelectrically cooled (TE-cooled) InAs/GaSb type-II superlattice (T2SL) single element infrared (IR) photodetectors and exemplify their applicability for real-time IR spectroscopy in the mid-infrared in a possible application. As the European Union’s Restriction of Hazardous Substances (RoHS) threatens the usage of the state-of-the-art detector material mercury cadmium telluride (MCT), RoHS-compatible alternatives to MCT have to be established for IR detection. We use bandgap engineered InAs/GaSb T2SLs to tailor the temperature-dependent bandgap energy for detection throughout the required spectral range. Molecular beam epitaxy of superlattice samples is performed on GaAs substrates with a metamorphic GaAsSb buffer layer. Photolithographic processing yields laterally-operated T2SL photodetectors. Integrated in a TE-cooled IR detector module, such T2SL photodetectors can be an alternative to MCT photodetectors for spectroscopy applications. Here, we exemplify this by exchanging a commercially available MCT-based IR detector module with our T2SL-based IR detector module in a real-time mid-infrared backscattering spectroscopy system for substance identification. The key detector requirements imposed by the spectroscopy system are a MHz-bandwidth, a broad spectral response, and a high signal-to-noise ratio, all of which are covered by the reported T2SL-based IR detector module. Hence, in this paper, we demonstrate the versatility of TE-cooled InAs/GaSb T2SL photodetectors and their applicability in an IR spectroscopy system.

Acquisition and Processing Considerations for Infrared Images of Rotating Turbine Blades

As designers aim to increase efficiency in gas turbines for aircraft propulsion and power generation, spatially-resolved experimental measurements are needed to validate computational models and compare improvement gains of new cooling designs. Infrared (IR) thermography is one such method for obtaining spatially-resolved temperature measurements. As technological advances in thermal detectors enable faster integration times, surface temperature measurements of rotating turbine blades become possible to capture including the smallest features. This paper outlines opportunities enabled by the latest IR detector technologies for capturing spatially-resolved rotating blade temperatures, while also addressing some of the challenges of implementing IR for turbine rigs such as the one in the Steady Thermal Aero Research Turbine (START) Laboratory. This paper documents critical steps in achieving accurate measurements including calibration, integration times, spatial noise, and motion blur. From these results, recommendations are provided for achieving accurate IR measurements collected in a rotating turbine facility to study film cooling.

Plasmonic-Layered InAs/InGaAs Quantum-Dots-in-a-Well Pixel Detector for Spectral-Shaping and Photocurrent Enhancement

The algorithmic spectrometry as an alternative to traditional approaches has the potential to become the next generation of infrared (IR) spectral sensing technology, which is free of physical optical filters, and only a very small number of data are required from the IR detector. A key requirement is that the detector spectral responses must be engineered to create an optimal basis that efficiently synthesizes spectral information. Light manipulation through metal perforated with a two-dimensional square array of subwavelength holes provides remarkable opportunities to harness the detector response in a way that is incorporated into the detector. Instead of previous experimental efforts mainly focusing on the change over the resonance wavelength by tuning the geometrical parameters of the plasmonic layer, we experimentally and numerically demonstrate the capability for the control over the shape of bias-tunable response spectra using a fixed plasmonic structure as well as the detector sensitivity improvement, which is enabled by the anisotropic dielectric constants of the quantum dots-in-a-well (DWELL) absorber and the presence of electric field along the growth direction. Our work will pave the way for the development of an intelligent IR detector, which is capable of direct viewing of spectral information without utilizing any intervening the spectral filters.