Failure analysis of excavator hydraulic pump

Hydraulic pump failures may be related to hardware or problem in oil. In this study, the excavator hydraulic pump failures were investigated by using visual observed and measuring the part component. The disassembled process of the pump was performed considering the manual part book of the excavator hydraulic pump. The abrasive wear on the pump slipper and swash plate was observed by comparing the guidelines for the reusable part. The value of more than 1.07 mm clearance within piston and cylinder bore was measured then the results over the allowable limit considering the manual part book. Properly analyzing of component failure can provide valuable information about what caused the failure and thus can be to avoiding future unscheduled downtime.

Aflatoxins in bird feed collected from various areas of Lahore city

The objective of this study was to estimate total aflatoxin in bird feed. Total 50 birds feed samples were collected from different markets and birds shops in Lahore. Total aflatoxin B1, B2, G1, and G2 were estimated using the Thin Layer Chromatography (TLC) method. The daily intake of aflatoxin in bird's feed is a 300ppb threshold by FDA. Total 50 samples were examined, among them 22% were contaminated with aflatoxin B1 and B2 and the rest of 40% samples were contaminated only with aflatoxin B1. Aflatoxin G1 and G2 were not detected in any feed. The results showed that 42% of samples were contaminated within the permissible limit, 20% were unfit due to having above the allowable limit, and 38% were fit, which did not show any aflatoxin. The current study has demonstrated the easy way of providing the determination of aflatoxin in bird’s feed. Bangladesh J. Sci. Ind. Res.56(4), 249-254, 2021

Analytical Profiling of Heavy Metals Contamination in soils, Dismantling Dust, and Rubber Samples in Karachi City Using AAS, WD-XRF, and SEM Technique

The concentrations of Cd, Cr, Cu, Fe, Ni, Pb, & Zn were determined in the samples of soil, dismantling dust and rubber collected from the electronic waste dumping site of Shershah market and rubber from the Local market of Karachi city Pakistan. The city e-waste dumping and dismantling sites toxicity were not conducted before using modern techniques. The subsequent data of the heavy metals concentration were obtained using Atomic Absorption Spectrometry (AAS), Scanning Electron Microscopy (SEM), and Wavelength Dispersive- X-Ray Fluorescence Spectrometry (WD-XRF). Cu, Pb, and Zn were found as 133.17, 104.53 & 113.26 in soil, whereas in dismantling dust Pb & Zn were remained 10.56 and 12.65 mg/kg similarly. The China toy particle analysis by SEM was resulting metallic trend as Fe > Zn > Pb > Cd > Ni > Cr. The estimated data were compared with the levels allowed by the Pakistan Environmental Protection Agency (Pak-EPA) and the United States Environmental Protection Agency (USEPA). The maximum allowable limit for Cd is 3; Cr, Cd, and Pb are 100 for Ni is 50 and 300 mg/kg for Zn. The presence of these heavy metals from e-waste dumping would become soon a significant reason to cause serious health problems for the nearby residents and as well as city too. It has been concluded that the dumping of e-waste is the major source of contamination of heavy metals in the studied media. It is recommended that the e-waste must be recycled formally to prevent the soil from being polluted. .

Method Development and Validation of Montelukast in API and Pharmaceutical Dosage Form by UV Spectrophotometry

The present work is done to develop a new simple, rapid, specific, accurate and precise UV spectrophotometric method for Montelukast as API and in pharmaceutical dosage form. The validation of the proposed method was carried out according to the I.C.H guidelines. The wavelength maxima was found 270nm and calibration curves were obtained in the concentration range 5-45?g/ml for montelukast with good correlation coefficients (r2=0.9994.). The precisions of the new method for montelukast was less than the maximum allowable limit (%RSD <2.0) specified by the ICH. Therefore, the method was found to be an accurate, reproducible and sensitive for analysis of montelukast as standard, pharmaceutical dosage forms, and other routine analysis method.

Assessment of environmental pollution level caused by shipbuilding industry

The purpose of the paper was to create databases that would allow a proper assessment of the degree of marine pollution generated by the shipyard industrial sector. The study was conducted over a period of three years, between 2015 and 2017. The parameters determined for the waters collected from the shipyard were within the maximum allowed limits according to the norms in force. However, values very close to the maximum allowable limit were observed in the case of groundwater for nickel, determined from the drilling located near the fuel depot in 2015 and chlorides determined from the drilling located near the galvanizing workshop, both in 2016 and in 2017. The analyzed parameters for the soil samples, collected from various sampling points and different depths, were below the value of the alert thresholds for less sensitive soils, according to Order 756/97. The databases created for this study can contribute as an incipient basis for the development of larger studies that include other industrial sectors as well as a longer evaluation period.

RP-HPLC Method Development and Validation for Simultaneous Estimation of Thymoquinone and Curcumin in Dosage form

Aim: The aim of work is to develop and validate simple, specific, accurate, precise HPLC method for the estimation of Curcumin (CUR) and Thymoquinone (THQ) simultaneously in bulk and its formulation as per ICH guidelines for analytical method development and validation. Study Design: Developing RP-HPLC method using C-18 Inertsil column and optimization of variables for estimation of Thymoquinone and Curcumin in bulk and formulation. Place and Duration of Study: The present work was carried out at Shri D. D. Vispute College of Pharmacy and Research Center, Panvel in year 2021. Methodology: The RP-HPLC method was developed with an isocratic condition of mobile phase comprising acetonitrile and water in a ratio of (82:18) v/v, at a flow rate of 0.9 mL/minute over Inertsil ODS, 250× 4.6 mm, 5 µm column, at 30°C column oven temperature. Photodiode array at 256 nm was used for detection Results: Retention time for curcumin and thymoquinone was found to be 3.5 and 4.3 mins respectively. The method showed excellent linear response in concentration range of 4-18 µg/mland 10-45 µg/mlfor thymoquinone and curcuminrespectively with correlation coefficient (R2) values of0.999 for both. System precision and method precision studies were less than the maximum allowable limit percentage of relative standard deviation ≤ 2.0 i.e., 1.61 % and 1.62 % for curcumin and 0.47 % and 0.42 % for thymoquinone respectively. Mean % Recovery for both the drugs were within acceptance limits. The developed and validated HPLC method is simple, accurate, precise and suitable for analysis as all the results were within acceptance criteria. Conclusion: The developed RP-HPLC method at single wavelength was validated according to ICH guideline with respect to system suitability, specificity, linearity, accuracy, precision and robustness and can be used for routine quality monitoring of drug in pharmaceutical dosage form.

Total Petroleum Hydrocarbons Contamination of the Surface Water and Sediments of Orashi River, Engenni, Ahoada West, Rivers State, Nigeria

The level of contamination of Orashi River by total petroleum hydrocarbons were investigated through the collection of surface water samples and sediment samples from four locations along the river. Determination of the level of contamination was done with the use of gas chromatography-flame ionization detector after following laid down clean-up procedures. The results obtained showed that total petroleum hydrocarbons in the surface water were 10.913±2.2022mg/L, 7.645±2.683mg/L, 9.074±2.1654mg/L and 12.212±3.3034mg/L for stations 1, 2, 3 and 4 respectively with a mean value of 9.961±2.5885mg/L, while in the sediment samples concentration values recorded were 22.3925±5.2104mg/Kg, 35.1071±9.9652mg/Kg, 50.4431±15.9916mg/Kg and 29.3869±8.0410mg/Kg for stations 1, 2 3 and 4 respectively with a mean value of 34.3324±9.8021mg/Kg. The partition coefficient calculations revealed that the sediment phase is more stable for total petroleum hydrocarbons as compared to the water phase. The analysis of the randomly collected samples revealed that total petroleum hydrocarbons have contaminated the river and therefore adequate steps should be taken to remedy the present condition of the Orashi River in order to mitigate any probable rise in the quantity of total petroleum hydrocarbons in the river above allowable limit.

Comparison of a Biosensor and a Commercial UV-Visible Method for Measuring Hexavalent Chromium in Liquid Medium

The objective of the research was to contrast two methods for the quantification of hexavalent chromium. The first method is the biosensor that from the gene transformation of the cells of Escherichia coli, was incorporated by electroporation the plasmid pTOP Blunt V2, synthesized with luxA genes that provides luminescence through the catalytic activity of the luciferase top and chr genes that give the bacteria resistance to chromium. The second method is the application of the UV-visible colorimetric technique. Chromium was analysed at different concentrations, from 0.05 mg l−1 (maximum allowable limit for human consumption); 0.1 mg l−1; 0.2 mg l−1; 0.4 mg l−1; 0.8 mg l−1 and 1 mg l−1 with 5 replicates, subsequent to this, the two methods of chromium analysis were applied in river samples, thus obtaining that the biosensor in concentrations of 2x106 CFU of E. coli, has a margin of error of 1.4%, a result derived from the coefficient of determination of the absorbance of chromium, unlike the UV-visible method with the colorimetric equipment, which presented a reading error of 3.9%.

Assessment of significant metals in effluents, soil, and pond water of tanneries south of capital of Sudan state

In the present study, impact of tannery effluents and their subsequent on accumulation of some metals (Ca, K, Na, Mg, Cl, S, Cr, Fe, Mn, Pb, and Zn) in water and soil samples in and around South Khartoum industrial area, Khartoum-Sudan were studied. Concentration of metals in tannery effluents (SA), adjacent contaminated pond water (SB), Soil (SC), and uncontaminated water (SD) were assessed by atomic absorption photometer. The results showed high levels of Ca, K, Na, Mg, Cl, S, Cr, Fe, Mn, Pb, and Zn within the water from all sampling point (SA, SB and SC). The investigation exhibited that tanneries wastewater has high mean concentrations of Cr, Fe, Mn, and Pb in all sampling point of effluent, pond water, soil, and uncontaminated water, except Zn which is high only in soil sampling point (SC). The significant metals accumulation displayed a pattern of mean concentration as follow: Soil > Effluent >contaminated pond water > Un contaminated water. Significant metals toxicity levels within the totally different sampling points were compared with water from WHO. Mean metal concentrations in un contaminated water were among the allowable limit set by WHO except for Magnesium (Mg). The comparison indicated that soil (SC) within the neighboring industrial area accumulated metals, enhanced levels of toxic of metals such as Cr, Ni, Zn and Pb, which also demonstrated higher concentration levels in the adjacent contaminated pond water samples. increased levels of poisonous, that additionally incontestable higher concentration levels within the contaminated pond water.

Finite Element Method for Ship Composite-Based on Aluminum

The structure and construction of ships made of aluminum alloy, generally of the type of wrought aluminum alloy, when experiencing fatigue failure caused by cracking of the ship structure, is a serious problem. Judging from the ‘weaknesses’ of aluminum material for ships, this chapter will explain the use of alternative materials for ship building, namely aluminum-based composite material which is an aluminum alloy AlSi10Mg (b) ship building material based on the European Nation (EN) Aluminum Casting (AC) - 43,100, with silicon carbide (SiC) reinforcement which has been treated with an optimum composition of 15%, so that the composite material is written with EN AC-43100 (AlSi10Mg (b) + SiC * / 15p. Composite ship model using ANSYS (ANalysis SYStem) software to determine the distribution of stress. The overall result of the voltage distribution has a value that does not exceed the allowable stress (sigma 0.2) and has a factor of safety above the minimum allowable limit, so it is safe to use. The reduction in plate thickness on the EN AC-43100 (AlSi10Mg (b)) + SiC * /15p composite vessel is significant enough to reduce the ship’s weight, so it will increase the speed of the ship.