Molecular Origin of Fast Evaporation at the Solid–water–vapor Line in a Sessile Droplet

By analyzing the behaviors of water molecules at the solid–water–vapor contact line, we explore the molecular origins of large evaporation rates at the contact line and find new ways to...

Effect of Spontaneous and Water-Based Passivation on Components and Parameters of Ti6Al4V (ELI Grade) Surface Tension and Its Wettability by an Aqueous Solution of Sucrose Ester Surfactants

Solid wettability is especially important for biomaterials and implants in the context of microbial adhesion to their surfaces. This adhesion can be inhibited by changes in biomaterial surface roughness and/or its hydrophilic–hydrophobic balance. The surface hydrophilic–hydrophobic balance can be changed by the specifics of the surface treatment (proper conditions of surface preparation) or adsorption of different substances. From the practical point of view, in systems that include biomaterials and implants, the adsorption of compounds characterized by bacteriostatic or bactericidal properties is especially desirable. Substances that are able to change the surface properties of a given solid as a result of their adsorption and possess at least bacteriostatic properties include sucrose ester surfactants. Thus, in our studies the analysis of a specific surface treatment effect (proper passivation conditions) on a biomaterial alloy’s (Ti6Al4V ELI, Grade 23) properties was performed based on measurements of the contact angles of water, formamide and diiodomethane. In addition, the changes in the studied solid surface’s properties resulting from the sucrose monodecanoate (SMD) and sucrose monolaurate (SML) molecules’ adsorption at the solid–water interface were also analyzed. For the analysis, the values of the contact angles of aqueous solutions of SMD and SML were measured at 293 K, and the surface tensions of the aqueous solutions of studied surfactants measured earlier were tested. From the above-mentioned tests, it was found that water environment significantly influences the components and parameters of Ti6Al4V ELI’s surface tension. It also occurred that the addition of both SMD and SML to water (separately) caused a drop in the water contact angle on Ti6Al4V ELI’s surface. However, the sucrose monolaurate surfactant is characterized by a slightly better tendency towards adsorption at the solid–water interface in the studied system compared to sucrose monodecanoate. Additionally, based on the components and parameters of Ti6Al4V ELI’s surface tension calculated from the proper values of components and parameters of model liquids, it was possible to predict the wettability of Ti6Al4V ELI using the aqueous solutions of SMD and SML at various concentrations in the solution.

Successive H-atom Addition to Solid OCS on Compact Amorphous Solid Water

Carbonyl sulfide (OCS) is an abundant sulfur (S)-bearing species in the interstellar medium. It is present not only in the gas phase, but also on interstellar grains as a solid; therefore, OCS very likely undergoes physicochemical processes on icy surfaces at very low temperatures. The present study experimentally and computationally investigates the reaction of solid OCS with hydrogen (H) atoms on amorphous solid water at low temperatures. The results show that the addition of H to OCS proceeds via quantum tunneling, and further addition of H leads to the formation of carbon monoxide (CO), hydrogen sulfide (H2S), formaldehyde (H2CO), methanol (CH3OH), and thionformic acid (HC(O)SH). These experimental results are explained by our quantum chemical calculations, which demonstrate that the initial addition of H to the S atom of OCS is the most predominant, leading to the formation of OCS-H radicals. Once the formed OCS-H radical is stabilized on ice, further addition of H to the S atom yields CO and H2S, while that to the C atom yields HC(O)SH. We have also confirmed, in a separate experiment, the HC(O)SH formation by the HCO reactions with the SH radicals. The present results would have an important implication for the recent detection of HC(O)SH toward G+0.693–0.027.

Tunneling of Hydrogen and Deuterium Atoms on Interstellar Ices (Ih and ASW)

Model calculations are performed to investigate the kinetic isotope effect of hydrogen and deuterium atom diffusion on hexagonal ice and amorphous solid water. Comparisons with experimental results by Kuwahata et al. (Phys. Rev. Lett., Sep. 2015, 115 (13), 133201) at 10 K are made. The experimentally derived kinetic isotope effect on amorphous solid water is reproduced by transition state theory. The experimentally found kinetic isotope effect on hexagonal ice is much larger than on amorphous solid water and is not reproduced by transition state theory. Additional calculations using model potentials are made for the hexagonal ice, but the experimental kinetic isotope effect is not fully reproduced. A strong influence of temperature is observed in the calculations. The influence of tunnelling is discussed in detail and related to the experiments. The calculations fully support the claims by the Kuwahata et al. (Phys. Rev. Lett., Sep. 2015, 115 (13), 133201) that on amorphous solid water the diffusion is predominantly by thermal hopping while on the polycrystalline ice tunnelling diffusion contributes significantly.