sweep efficiency
Recently Published Documents


TOTAL DOCUMENTS

528
(FIVE YEARS 153)

H-INDEX

26
(FIVE YEARS 5)

2022 ◽  
Author(s):  
Maria Serena Magna Detto Calcaterra ◽  
Pierluigi Sedda ◽  
Giacomo Fulceri ◽  
Salvatore Luppina ◽  
Luca Mauri ◽  
...  

Abstract Primary production mechanism of a clean sandstone reservoir in a brownfield for oil production has been recently changed from natural depletion to waterflooding. Despite the apparently moderate petro-physical properties of the formation, injector wells performances were observed to be extremely poor, mainly due to: high drilling-induced formation damage and Fluids interaction within the reservoir (injection across the oil rim section). Several stimulation technologies have been applied to improve wells injection capability for pressure support optimization. Re-perforation via abrasive jetting, perforations wash through coiled tubing and various acid formulations via bullheading were attempted without achieving any significant increase in injectivity. Considering the modest rock permeability, the need to access a wider formation area to improve oil sweep efficiency and the crucial requirement to re-pressurize the reservoir, an additional card was played as last resort: hydraulic fracturing. This technique was not new to the area and already experimented by different operators. Several producer wells in different layers were hydraulic fracturing stimulated with proppant and/or acid in the past with a good rate of success. Why not to try then? Given the past experience on the same field with hydraulic fracturing in oil producers and accounting for well integrity and potential injectivity, one was chosen as suitable candidate. Offset wells hystorical data were used to build a hydraulic fracturing reservoir model and plan for the activity in details; operator and service providers engaged in a Frac Well On Paper activity in order to reduce any margin of error during field operations. An approach that proved successful. From there, the first trial well was planned and performed successfully. 4 other hydraulic fracturing jobs on 4 wells followed at close distance in time with different, but steadily comforting, results. Injection was improved from negligible initial values up to 2000 mc/day for the post-stimulation condition, exceeding the preliminary expectations. This paper introduces the steps taken to start the hydraulic fracturing campaign, the decision process that led to the design of the treatment, an overview of the execution phases, results well by well and lessons learned to optimize future campaigns.


Author(s):  
M. М. Irani ◽  
◽  
V. P. Telkov ◽  

Water-gas influence (WGI) is an oil recovery method improving displacement ratio, sweep efficiency and adjusting the alignment of displacement. This study is a review of the traditional WAG methods (Immiscible WAG, Hybrid WAG, Simultaneous WAG and Selective Simultaneous WAG), including with stabilizing surfactants, WAG. We also consider such sparsely used methods as: SSWAG, FAWAG, CWAG, TWAG, VR-WAG, Up- and Down-dip WAG, HC-WAG, PAG, SAG, WASP, LSW WAG, LSASF, SMSW-AGF and others. The advantages and disadvantages of these tools are considered. Keywords: water-gas influence (WGI); WAG; SWAG; enhanced oil recovery; APG


2021 ◽  
Author(s):  
Klemens Katterbauer ◽  
Alberto Marsala ◽  
Abdallah Al Shehri ◽  
Ali Yousif

Abstract 4th Industrial Revolution (4IR) technologies have assumed critical importance in the oil and gas industry, enabling data analysis and automation at unprecedented levels. Formation evaluation and reservoir monitoring are crucial areas for optimizing reservoir production, maximizing sweep efficiency and characterizing the reservoirs. Automation, robotics and artificial intelligence (AI) have led to tremendous transformations in these areas, in particular in subsurface sensing. We present a novel 4IR inspired framework for the real-time sensor selection for subsurface pressure and temperature monitoring, as well as reservoir evaluation. The framework encompasses a deep learning technique for sensor data uncertainty estimation, which is then integrated into an integer programming framework for the optimal selection of sensors to monitor the reservoir formation. The results are rather promising, showing that a relatively small numbers of sensors can be utilized to properly monitor the fractured reservoir structure.


2021 ◽  
Author(s):  
Ayman Al-Nakhli ◽  
Hussain Al-Jeshi ◽  
Olalekan Alade ◽  
Mohamed Mahmoud ◽  
Wajdi Buhaezah

Abstract One of the typical production challenges is occurrence of impermeable layers of highly viscous asphaltenic oil (known as tarmat) at oil/water contact within a reservoir. Tar forms a physical barrier that isolates producing zones from aquifer or water injectors. As a result of tar occurrence, is a rapid pressure decrease that can be observed in such reservoirs, increasing number of dead wells, and declining productivity. Another indirect consequence of Tar presence is poor sweep efficiency that leads to water cut increase by a drastic magnitude. An innovative approach was developed to establish better sweep efficiency, transmissibility and pressure maintenance of Tar impacted-areas using thermochemical treatment. The treatment consists of injecting exothermic reaction-components that react downhole and generate in-situ pressure and heat. The in-situ reaction products provide heat and gas-drive energy to mobilize tar, improve sweep efficiency and maintain flooding for better pressure maintenance. Typically, downhole heat generation through chemical reaction releases substantial heat which could be employed in various thermal stimulation operations. Nano/ionic liquids, high pH solutions, solvents and nano metals were combined with the exothermic reaction to improve tar mobilization. Based on lab testing, the new technology showed more recovery than conventional steam flooding. Permeable channels were created in a tar layer with sandback samples, which enhanced transmissibility, pressure support and sweep efficiency. The effect of thermochemical treatment and ionic liquid on bitumen texture will be described. Impact of In-situ generated heat on injectivity will also be presented. The novel method will enable commercial production from tar-impacted reservoirs, and avoid costly steam flooding systems. The developed novel treatment relates to in-situ steam generation to maximize heat delivery efficiency of steam into the reservoir and to minimize heat losses due to under and/or over burdens. The generated in-situ steam and gas can be applied to recover deep oil reservoirs, which cannot be recovered with traditional steam, miscible gas, nor polymer injection methods.


2021 ◽  
Author(s):  
Mohd Ghazali Abd Karim ◽  
Wahyu Hidayat ◽  
Alzahrani Abdulelah

Abstract The objective of this paper is to investigate the effects of interfacial tension dependent relative permeability (Kr_IFT) on oil displacement and recovery under different gas injection compositions utilizing a compositional simulation model. Oil production under miscible gas injection will result in variations of interfacial tension (IFT) due to changes in oil and gas compositions and other reservoir properties, such as pressure and temperature. Laboratory experiments show that changes in IFT will affect the two-phase relative permeability curve (Kr), especially for oil-gas system. Using a single relative permeability curve during the process from immiscible to miscible conditions will result in inaccurate gas mobility against water, which may lead to poor estimation of sweep efficiency and oil recovery. A synthetic sector compositional model was built to evaluate the effects of this phenomenon. Several simulation cases were investigated over different gas injection compositions (lean, rich and CO2), fluid properties and reservoir characterizations to demonstrate the impact of these parameters. Simulation model results show that the application of Kr_IFT on gas injection simulation modelling has captured different displacement behavior to provide better estimation of oil recovery and identify any upside potential.


2021 ◽  
Author(s):  
Klemens Katterbauer ◽  
Abdallah Al Shehri ◽  
Alberto Marsala

Abstract Waterfront movement in fractured carbonate reservoirs occurs in micro-fractures, corridors and interconnected fracture channels (above 5 mm in size) that penetrate the carbonate reservoir structure. Determining the fracture channels and the waterfront movements within the flow corridors is critical to optimize sweep efficiency and increase hydrocarbon recovery. In this work, we present a new deep reinforcement learning algorithm for the optimization of sensor placement for waterfront movement detection in carbonate fracture channels. The framework deploys deep reinforcement learning approach for optimizing the location of sensors within the fracture channels to enhance waterfront tracking. The approach first deploys the deep learning algorithm for determining the water saturation levels within the fractures based on the sensor data.. Then, it updates the sensor locations in order to optimize the reservoir coverage. We test the deep reinforcement learning framework on a synthetic fracture carbonate reservoir box model exhibiting a complex fracture system. Fracture Robots (FracBots, around 5 mm in size) technology will be used to sense key reservoir parameters (e.g., temperature, pressure, pH and other chemical parameters). The technology is comprised of a wireless micro-sensor network for mapping and monitoring fractures in conventional and unconventional reservoirs [1]. It establish a wireless network connectivity via magnetic induction (MI)-based communication since it exhibits highly reliable and constant channel conditions with sufficient communication range in the oil reservoir environment. The system architecture of the FracBots network has two layers: FracBot nodes layer and a base station layer. A number of subsurface FracBot sensors are injected in the formation fractures that record data affected by changes in water saturation. The sensor placement can be adapted in the reservoir formation to improve sensor data quality, as well as better track the penetrating waterfronts. They will move with the injected fluids and distribute themselves in the fractures where they start sensing the surrounding environment's conditions and communicate data, including their location coordinates, among each other to finally send the information in multi-hop fashion to the base station installed inside the wellbore. The base station layer consists of a large antenna connected to an aboveground gateway. The data collected from the FracBots network will be transmitted to the control room via aboveground gateway for further processing. The results exhibited resilient performance in updating the sensor placement to capture the penetrating waterfronts in the formation. The framework performs well particularly when the distance between the sensors is sufficient to avoid measurement interference. The framework demonstrates the criticality of adequate sensor placement in the reservoir formation for accurate waterfront tracking. Also, it shows that itis a viable solution to optimize sensor placement for reservoir monitoring. This novel framework presents a vital component in the data analysis and interpretation of subsurface reservoir monitoring system for carbonate reservoirs. The results outline the opportunity to deploy advanced artificial intelligence algorithms, such as deep reinforcement methods, to optimally place downhole sensors to achieve best measurement success, and track the waterfronts as well as determine sweep efficiency.


2021 ◽  
Author(s):  
Mohammed T. Al-Murayri ◽  
Abrahim Hassan ◽  
Naser Alajmi ◽  
Jimmy Nesbit ◽  
Bastien Thery ◽  
...  

Abstract Mature carbonate reservoirs under waterflood in Kuwait suffer from relatively low oil recovery due to poor volumetric sweep efficiency, both areal, vertically, and microscopically. An Alkaline-Surfactant-Polymer (ASP) pilot using a regular five-spot well pattern is in progress targeting the Sabriyah Mauddud (SAMA) reservoir in pursuit of reserves growth and production sustainability. SAMA suffers from reservoir heterogeneities mainly associated with permeability contrast which may be improved with a conformance treatment to de-risk pre-mature breakthrough of water and chemical EOR agents in preparation for subsequent ASP injection and to improve reservoir contact by the injected fluids. Each of the four injection wells in the SAMA ASP pilot was treated with a chemical conformance improvement formulation. A high viscosity polymer solution (HVPS) of 200 cP was injected prior to a gelant formulation consisting of P300 polymer and X1050 crosslinker. After a shut-in period, wells were then returned to water injection. Injection of high viscosity polymer solution (HVPS) at the four injection wells showed no increase in injection pressure and occurred higher than expected injection rates. Early breakthrough of polymer was observed at SA-0561 production well from three of the four injection wells. No appreciable change in oil cut was observed. HVPS did not improve volumetric sweep efficiency based on the injection and production data. Gel treatment to improve the volumetric conformance of the four injection wells resulted in all the injection wells showing increased of injection pressure from approximately 3000 psi to 3600 psi while injecting at a constant rate of approximately 2,000 bb/day/well. Injection profiles from each of the injection well ILTs showed increased injection into lower-capacity zones and decreased injection into high-capacity zones. Inter-well tracer testing showed delayed tracer breakthrough at the center SA-0561 production well from each of the four injection wells after gel placement. SA-0561 produced average daily produced temperature increased from approximately 40°C to over 50°C. SA-0561 oil cuts increased up to almost 12% from negligible oil sheen prior to gel treatments. Gel treatment improved volumetric sweep efficiency in the SAMA SAP pilot area.


2021 ◽  
Author(s):  
Vitaly Virt ◽  
Vladimir Kosolapov ◽  
Vener Nagimov ◽  
Andrey Salamatin ◽  
Yulia Fesina ◽  
...  

Abstract Profitable development of hard-to-recover reserves often involves drilling of horizontal wells with multistage hydraulic fracturing to increase the oil recovery factor. Usually to monitor the fracture sweep efficiency, pressure transient analysis is used. However, in case of several fractures this method delivers only average hydrodynamic parameters of the well-fracture system. This paper illustrates the value of temperature logging data and demonstrates possibilities of the 3-D thermo-mechanical modelling in evaluating the differential efficiency of multi-stage hydraulic fracturing.


2021 ◽  
Author(s):  
S.A. Baloch ◽  
J.M. Leon ◽  
S.K. Masalmeh ◽  
D. Chappell ◽  
J. Brodie ◽  
...  

Abstract Over the last few years, ADNOC has systematically investigated a new polymer-based EOR scheme to improve sweep efficiency in high temperature and high salinity (HTHS) carbonate reservoirs in Abu Dhabi (Masalmeh et al., 2014). Consequently, ADNOC has developed a thorough de-risking program for the new EOR concept in these carbonate reservoirs. The de-risking program includes extensive laboratory experimental studies and field injectivity tests to ensure that the selected polymer can be propagated in the target reservoirs. A new polymer with high 2-acrylamido-tertiary-butyl sulfonic acid (ATBS) content was identified, based on extensive laboratory studies (Masalmeh, et al., 2019, Dupuis, et al., 2017, Jouenne 2020), and an initial polymer injectivity test (PIT) was conducted in 2019 at 250°F and salinity >200,000 ppm, with low H2S content (Rachapudi, et al., 2020, Leon and Masalmeh, 2021). The next step for ADNOC was to extend polymer application to harsher field conditions, including higher H2S content. Accordingly, a PIT was designed in preparation for a multi-well pilot This paper presents ADNOC's follow-up PIT, which expands the envelope of polymer flooding to dissolve H2S concentrations of 20 - 40 ppm to confirm injectivity at representative field conditions and in situ polymer performance. The PIT was executed over five months, from February 2021 to July 2021, followed by a chase water flood that will run until December 2021. A total of 108,392 barrels of polymer solution were successfully injected during the PIT. The extensive dataset acquired was used to assess injectivity and in-depth mobility reduction associated with the new polymer. Preliminary results from the PIT suggest that all key performance indicators have been achieved, with a predictable viscosity yield and good injectivity at target rates, consistent with the laboratory data. The use of a down-hole shut-in tool (DHSIT) to acquire pressure fall-off (PFO) data clarified the near-wellbore behaviour of the polymer and allowed optimisation of the PIT programme. This paper assesses the importance of water quality on polymer solution preparation and injection performance and reviews operational data acquired during the testing period. Polymer properties determined during the PIT will be used to optimise field and sector models and will facilitate the evaluation of polymer EOR in other giant, heterogeneous carbonate reservoirs, leading to improved recovery in ADNOC and Middle East reservoirs.


2021 ◽  
Author(s):  
Ying Yu ◽  
Alvinda Sri Hanamertani ◽  
Shehzad Ahmed ◽  
Zunsheng Jiao ◽  
Jonathan Fred McLaughlin ◽  
...  

Abstract Injecting carbon dioxide (CO2) as foam during enhanced oil recovery (EOR) can improve injectate mobility and increase sweep efficiency. Integrating CO2-foam techniques with carbon capture, utilization and storage (CCUS) operations is of recent interest, as the mobility control and sweep efficiency increases seen in EOR could also benefit CO2 storage during CCUS. In this study, a variety of different charge, hydrocarbon chain length, head group surfactants were evaluated by surface tension, bulk and dynamic CO2-foam performance assessments for CCUS. The optimal foam candidate was expected to provide satisfying mobility control effects under reservoir conditions, leading to an improved water displacement efficiency during CO2-foam flooding that favors a more significant CO2 storage potential. All tested surfactants were able to lower their surface tensions against scCO2 by 4-5 times, enlarging the surface area of solution/gas contact; therefore, more CO2 could be trapped in the foam system. A zwitterionic surfactant was found to have slightly higher surface tension against CO2 while exhibiting the highest foaming ability and the most prolonged foam stability with a relatively slower drainage rate among all tested surfactants. The dynamic performance of scCO2-foam stabilized by this zwitterionic surfactant was also evaluated in sandstone and carbonate cores at 13.79 MPa and 90°C. The results show that the mobility control development in carbonate core was relatively slower, suggesting a gradual foam generation process attributed to the higher permeability than the case in sandstone core. A more significant cumulative CO2 storage potential improvement, quantified based on the water production, was recorded in sandstone (53%) over the carbonate (47%). Overall, the selected foam has successfully developed CO2 mobility control and improved water displacement in the occurrence of in-situ foam generation, hence promoting the storage capacity for the injected CO2. This work has optimized the foaming agent selection method at the actual reservoir conditions and evaluated the scCO2-foam performance in establishing high flow resistance and improving the CO2 storage capacity, which benefits integrated CCUS studies or projects utilizing CO2-foam techniques.


Sign in / Sign up

Export Citation Format

Share Document