porosity level
Recently Published Documents


TOTAL DOCUMENTS

132
(FIVE YEARS 41)

H-INDEX

13
(FIVE YEARS 3)

2022 ◽  
Author(s):  
Daniel Tejero-Martin ◽  
Mingwen Bai ◽  
Acacio R. Romero ◽  
Richard G. Wellman ◽  
Tanvir Hussain

Recession of environmental barrier coatings (EBC) in environments containing steam is a pressing concern that requires further research before their implementation in gas turbine engines can be realized. In this work, free-standing plasma sprayed Yb2Si2O7 coatings were exposed to flowing steam at 1350 °C and 1400 °C for 96 h. Three samples were investigated, one coating with a low porosity level (< 3 %) and 1 wt.% Al2O3 representing traditional EBCs; and two coatings with higher porosity levels (~20 %) representing abradable EBCs. Phase composition and microstructural evolution were studied in order to reveal the underlying mechanism for the interaction between high temperature steam and ytterbium disilicate. The results show depletion of Yb2SiO5 near the surface and formation of ytterbium garnet (Yb3Al5O12) on top of all three coatings due to the reaction with gaseous Al-containing impurities coming from the alumina furnace tubes. The 1 wt.% Al2O3 added to the EBC sample exacerbated the formation of garnet at 1400 °C compared to the abradable samples, which presented lower quantities of garnet. Additionally, inter-splat boundaries were visible after exposure, indicating preferential ingress of gaseous Al-containing impurities through the splat boundaries.


Materials ◽  
2021 ◽  
Vol 15 (1) ◽  
pp. 190
Author(s):  
Nur’ain Wahidah Ya Omar ◽  
Norshah Aizat Shuaib ◽  
Mohd Haidiezul Jamal Ab Hadi ◽  
Azwan Iskandar Azmi ◽  
Muhamad Nur Misbah

Carbon-fiber-reinforced plastic materials have attracted several applications, including the fused deposition modelling (FDM) process. As a cheaper and more environmentally friendly alternative to its virgin counterpart, the use of milled recycled carbon fiber (rCF) has received much attention. The quality of the feed filament is important to avoid filament breakage and clogged nozzles during the FDM printing process. However, information about the effect of material parameters on the mechanical and physical properties of short rCF-reinforced FDM filament is still limited. This paper presents the effect of fiber loading (10 wt%, 20 wt%, and 30 wt%) and fiber size (63 µm, 75 µm, and 150 µm) on the filament’s tensile properties, surface roughness, microstructure, porosity level, density, and water absorptivity. The results show that the addition of 63 µm fibers at 10 wt% loading can enhance filament tensile properties with minimal surface roughness and porosity level. The addition of rCF increased the density and reduced the material’s water intake. This study also indicates a clear trade-off between the optimized properties. Hence, it is recommended that the optimization of rCF should consider the final application of the product. The findings of this study provide a new manufacturing strategy in utilizing milled rCF in potential 3D printing-based applications.


2021 ◽  
Vol 9 (12) ◽  
pp. 1454
Author(s):  
Liyang Xu ◽  
Zihai Yan ◽  
Jiajia Yan ◽  
Qiliang Xu ◽  
Jiancai Zhu ◽  
...  

Crucial mechanical-chemical (MC) interactions occur during the cement hydration process in cement marine clay; however, the role of such an important element of the resulting strength has been subject to less investigation, particularly from the theoretical perspective. To overcome this scientific gap, an efficient strength-based model accounting for the coupled MC processes is proposed here. Based on the analysis of the cement hydration mechanism, the porosity was chosen as the main factor to characterize the influence of the MC interactions on the overall response. To verify the accuracy of the MC model, the unconfined compressive strength (UCS) experiment was conducted for the cement marine clay samples, and the corresponding simulation model was constructed using COMSOL multiphysics®. In addition, a comparison between the predicted results by the existing three strength models and the proposed MC model was performed. Subsequently, the sensitivity analysis and identification of mechanical parameters were carefully carried out. The obtained results show that the UCS strength for Taizhou clay ranges from 10.21 kPa to 354.2 kPa as the cement content increases from 10% to 20%, and the curing time varies from 3 days to 28 days. The mechanical parameters in the MC model can be obtained according to the porosity level. A reasonably good agreement between the UCS strength results of simulations and the experimentally observed data is reported. Additionally, the predicted UCS strength results by the MC model demonstrate the best correspondence with the measured values, indicating the high efficacy of the established model.


Metals ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 2048
Author(s):  
Kaiqiang Wu ◽  
Sin Wei Chee ◽  
Wen Sun ◽  
Adrian Wei-Yee Tan ◽  
Sung Chyn Tan ◽  
...  

Inconel 713C is a nickel-based superalloy usually considered as a material of poor weldability due to its susceptibility to hot cracking in the heat-affected zones. Cold spray, a solid-state deposition technology that does not involve melting, can be proposed as a methodology to deposit Inconel 713C for surface enhancement of other target components. In this study, Inconel 713C coating was deposited on Inconel 718 substrate with a high-pressure cold spray system. The coating was characterized in terms of microstructure, hardness, and wear properties. The cold-sprayed Inconel 713C coating has a low porosity level and refined grain structures. Microhardness of the Inconel 713C coating was much higher than the Inconel 718 substrate. The sliding wear tests showed that the wear resistance of the cold-sprayed Inconel 713C coating is three times higher than the Inconel 718 substrate, making the coating a suitable protective layer. The main wear mechanisms of the coating include oxidation, tribo-film formation, and adhesive wear.


Metals ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 2038
Author(s):  
Dibakor Boruah ◽  
Xiang Zhang

This study aims at investigating the effect of post-deposition solution treatment and ageing (STA) on improving the interfacial adhesion strength in cold spray (CS) Ti6Al4V coatings deposited on Ti6Al4V substrates, measured by the adhesive-free collar-pin pull-off (CPP) test. Solution treatment was performed at 940 °C for 1 h and ageing was carried out at 480 °C for 8 h. Investigations were carried out for specimens with three different pre-treatments of the substrate surface, namely grit-blasted, as-machined (faced on lathe machine), and ground. Additionally, the effect of post-deposition STA was studied in terms of phase analysis, microstructure, and porosity level. It was observed that STA led to complete interfacial mixing resulting in significantly improved adhesion strength (by more than 520%) with the maximum measured value of greater than 766 MPa for ground substrates, reaching 81% of the ultimate tensile strength of mill annealed Ti6Al4V.


Polymers ◽  
2021 ◽  
Vol 13 (19) ◽  
pp. 3435
Author(s):  
Edgar Franco-Urquiza ◽  
Raúl Saleme-Osornio ◽  
Rodrigo Ramírez-Aguilar

In this work, henequen and ixlte plant fibers were carbonized in a horizontal quartz tube furnace. Several carbonized and non-carbonized fiber fabric configurations were impregnated with a bio-based epoxy resin through the infusion process. The infrared spectra revealed characteristic bands of styrene instead of organic compounds, representing that the carbonization procedure was adequate to carbonize the plant fibers. The porosity volume ratio for the non-carbonized henequen laminates showed the highest number of voids >1.9%, and the rest of the composites had a similar void density between 1.2–1.7%. The storage modulus of the non-carbonized and carbonized henequen laminates resulted in 2268.5 MPa and 2092.1 MPa, respectively. The storage modulus of the carbonized ixtle laminates was 1541.4 MPa, which is 37.8% higher than the non-carbonized ixtle laminates and 12% higher than henequen composites. The laminates were subject to thermal shock cycling, and tomography scans revealed no alterations on the porosity level or in the cracks after the cycling procedure. Thermal shock cycling promoted the post-curing effect by increasing the glass transition temperature. The viscoelastic results showed a variation in the storage modulus when the carbonized fiber fabrics were located between natural fiber fabrics, which was attributed to more excellent compaction during the infusion process. Variations in the viscoelastic behavior were observed between the different types of natural fibers, which influenced the mechanical properties.


2021 ◽  
pp. 002199832110316
Author(s):  
Yavuz Sun ◽  
Engin Cevik ◽  
Yunus Turen ◽  
Hayrettin Ahlatci ◽  
Muhammet Emre Turan ◽  
...  

In this study, graphene nanoplatelets (GNPs) and boron carbide (B4C) nano reinforcements were incorporated to the pure magnesium (Mg). Powder metallurgy route was used to fabricate composite samples. Microstructures of specimens were examined and tensile, hardness, wear tests were performed to determine the mechanical and tribological performance of produced samples. The results indicate that the hardness was increased especially with the addition of 2% B4C and 0.5% GNPs reinforcements. A general trend was observed for the enhancements of yield and tensile strengths when nano reinforcements were added to the pure magnesium. The composite samples showed better wear resistance than the unreinforced sample. However, thermal conductivity began to decrease with the addition of B4C reinforcements. It is also observed that the porosity level was also higher for the composite samples.


Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3665
Author(s):  
Taisiya Ponomareva ◽  
Mikhail Ponomarev ◽  
Arseniy Kisarev ◽  
Maxim Ivanov

The proposed paper considers the opportunity of expanding the application area of wire arc additive manufacturing (WAAM) method by means of increasing the strength properties of deposited material, due to the implementation of aluminum wire with the addition of scandium and zirconium. For the experimental research, the welding wire 1575 of the Al-Mg-Sc-Zr system containing 0.23% Sc and 0.19% Zr was selected. The optimal welding parameters, ensuring the defect-free formation of deposited material with low heat input, were used. Porosity level was estimated. The thermal state was estimated by finite element simulation. Simulated thermal state was verified by comparison with thermocouples data. Post-heat treatment parameters that lead to maximum strength with good plasticity were determined. The maximum yield strength (YS) of 268 MPa and ultimate strength (UTS) of 403 MPa were obtained, while the plasticity was determined at least 16.0% in all WAAM specimens.


2021 ◽  
pp. 2140006
Author(s):  
B. R. Moya ◽  
A. C. Silva ◽  
A. Peláiz-Barranco ◽  
J. D. S. Guerra

(1–[Formula: see text]Bi[Formula: see text]Na[Formula: see text]TiO3–[Formula: see text]BaTiO3 lead-free ceramics have been obtained from the conventional solid-state reaction sintering method. The structural properties were investigated from X-ray diffraction and Raman spectroscopy techniques. Results revealed well-crystallized ceramic samples with perovskite structure. Microstructural properties, obtained from scanning electron microscopy measurements, have shown high density with very low porosity level. The dielectric response, analyzed as a function of the temperature and several frequencies, showed very broad peaks with a strong frequency dependence of the temperature for the maximum dielectric permittivity for the modified system. Results were analyzed considering the influence of the BaTiO3 content on the studied physical properties.


Sign in / Sign up

Export Citation Format

Share Document