Large Torsion Deformation: Centrosymmetric Reentrant Honeycomb

There exist some problems in the crash box and anti-collision beam sandwich structure, such as monotone deformation pattern and uneconomical energy absorption performance. In order to raise the deformation capacity and energy absorption performance of sandwich structure, centrosymmetric reentrant honeycomb (CRH) and hexagonal centrosymmetric reentrant honeycomb (HCRH) are proposed based on auxetic reentrant honeycomb (ARH) in this work. Based on HCRH, four kinds of transverse combination structures and two kinds of longitudinal combination structures are obtained. The results of specific energy absorption show that the energy absorption capacity of the angular contact homodromous combination structure (ACOC) is about 3 times that of the other three transverse combination structures. Compared with longitudinal heterodromous combination structure (LHEC), the energy absorption capacity of longitudinal homodromous combination structure (LHOC) is improved by 72.7%.

Investigation of specific energy absorption of natural fiber honeycomb sandwich structure composite as building construction material application

The usage of incorporating natural fibre in composite material has seen some potential to be used as a future building construction material due to its recyclability, lightweight and high-reliability feature. However, the issue of implementing natural fibre as building construction material in composites material concerns the structural integrity of the material. As the characteristics of the natural fibre honeycomb composite have been discovered more in terms of properties which ranges from its physical and chemical structural composition to the quasi-static impact collapse of the material, the absorption energy of the material in different cell geometry is unknown. Therefore, the purpose of this study involves the testing of the natural fibre honeycomb (NFH) composite made from cement fibre (face sheet) and corn starch (core) with regards to its crushing behaviour when subjected to flatwise compression load according to ASTM D-3410 standard to analyse the performance of energy absorption of NFH composite with different thicknesses of the hexagonal core and cell wall thickness to determine the Specific Energy Absorption of the material. The result obtained shows that the increasing thicknesses of the core and cell wall improves the ability of the composite to absorb more energy and the specific energy absorption is higher when both factors are increased.

A Dynamic Model and Parameter Identification of High Viscosity Magnetorheological Fluid-Based Energy Absorber with Radial Flow Mode

The excellent suspension stability of the high-viscosity linear polysiloxane magnetorheological fluid (HVLP MRF) makes it a great controlled medium for magnetorheological energy absorbers (MREAs). In our previous work, the Herschel–Bulkley flow model (HB model) was used to describe the shear-thinning rheological behavior and establish the dynamic model of an HVLP MRF-based MREA with radial flow mode. However, as the established model was implicit, the MREA response time increased and the buffer effect was degraded. To improve the time response characteristics, an explicit dynamic model based on the HB model incorporating minor losses (called the E-HBM model) is proposed in this study. The model parameters were identified based on the HBM model. To verify the E-HBM model, five evaluation parameters for the energy absorption performance of the MREA, that is, peak force, mean force, crush force efficiency, specific energy absorption, and stroke efficiency, were introduced to compare the theoretical results with the experimental results obtained using a high-speed drop tower facility with a mass of 600 kg. Then, the relative error of the crush force efficiency, specific energy absorption, and stroke efficiency was quantitatively and comprehensively analyzed considering the E-HBM model and experimental results. The results indicate that the proposed E-HBM model agrees with the impact behavior of the radial flow mode MREA.

Failure mode engineered high-energy-absorption metamaterials with biomimetic hierarchical microstructures and artificial grain boundaries

For numerous engineering applications, there is a high demand for protective lightweight structures with outstanding energy absorption performance and the ability to prevent catastrophic structural failures. In nature, most species have evolved with hierarchical biological structures that possess novel mechanical properties, including ultrahigh specific energy absorption, progressive laminated failure modes, and ability for crack arrestment, in order to defend themselves from hostile environments. In this study, a novel protective metamaterial having spherical hollow structures (SHSs) was developed with different hierarchical microstructures. An artificial failure mode engineering strategy was proposed by tailoring the microstructures of SHS unit cells. To demonstrate the effectiveness of the proposed method, a composite hierarchical SHS lattice structure was developed using a biomimetic laminated failure mode and through a hardening mechanism, mimicking crystal grain boundaries. The quasi-static compressive results indicated a significant improvement in the specific energy absorption, an enhanced plateau stress magnitude, and an obvious delay in the densification stage for the composite hierarchical SHS lattice owing to the constraining effect of its mesoscale grain boundaries and an increased number of intensively engineered laminated failure levels. This novel type of metamaterial was shown to be immensely beneficial in designing lightweight protective aerospace components such as turbine blade lattice infills.

Dynamic Behaviors of Mortar Reinforced with NiTi SMA Fibers under Impact Compressive Loading

In this study, a compressive impact test was conducted using the split Hopkinson pressure bar (SHPB) method to investigate SMA fiber-reinforced mortar’s impact behavior. A 1.5% fiber volume of crimped fibers and dog-bone-shaped fibers was used, and half of the specimens were heated to induce recovery stress. The results showed that the appearance of SMA fibers, recovery stress, and composite capacity can increase strain rate. For mechanical properties, the SMA fibers reduced dynamic compressive strength and increased the peak strain. The specific energy absorption of the reinforced specimens slightly increased due to the addition of SMA fibers and the recovery stress; however, the effect was not significant. The composite behavior between SMA fibers and the mortar matrix, however, significantly influenced the dynamic compressive properties. The higher composite capacity of the SMA fibers produced lower dynamic compressive strength, higher peak strain, and higher specific energy absorption. The composite behavior of the dog-bone-shaped fiber was less than that of the crimped fiber and was reduced due to heating, while that of the crimped fiber was not. The mechanical properties of the impacted specimen followed a linear function of strain rate ranging from 10 to 17 s−1; at the higher strain rates of about 49–67 s−1, the linear functions disappeared. The elastic modulus of the specimen was independent of the strain rate, but it was dependent on the correlation between the elastic moduli of the SMA fibers and the mortar matrix.

Experimental and Numerical Investigation of the Effect of Projectile Nose Shape on the Deformation and Energy Dissipation Mechanisms of the Ultra-High Molecular Weight Polyethylene (UHMWPE) Composite

The effect of projectile nose shape on the ballistic performance of the ultra-high molecular weight polyethylene (UHMWPE) composite was studied through experiments and simulations. Eight projectiles such as conical, flat, hemispherical, and ogival nose projectiles were used in this study. The deformation process, failure mechanisms, and the specific energy absorption (SEA) ability were systematically investigated for analyzing the ballistic responses on the projectile and the UHMWPE composite. The results showed that the projectile nose shape could invoke different penetration mechanisms on the composite. The sharper nose projectile tended to shear through the laminate, causing localized damage zone on the composite. For the blunt nose projectile penetration, the primary deformation features were the combination of shear plugging, tensile deformation, and large area delamination. The maximum value of specific energy absorption (SEA) was 290 J/(kg/m2) for the flat nose projectile penetration, about 3.8 times higher than that for the 30° conical nose projectile. Furthermore, a ballistic resistance analytical model was built based on the cavity expansion theory to predict the energy absorption ability of the UHMWPE composite. The model exhibited a good match between the ballistic resistance curves in simulations with the SEA ability of the UHMWPE composite in experiments.

Ballistic Performance Evaluation of Kevlar-Glass Fibre Hybrid Composite Laminate against Medium Velocity Impact

In this paper, the post ballistic impact behaviour of kevlar-glass fibre hybrid composite laminates was investigated against 9×19 mm projectile. Eight different types of composite laminates with different ratios of kevlar woven fibre to glass fibre were fabricated using hand lay-up with epoxy matrix. Ballistic behaviour like ballistic Limit (V50), energy absorption, specific energy absorption and Back Face Signature (BFS) were studied after bullet impact. The results indicated that as the Percentage of glass fibre is increased there was a linear increment in the ballistic behaviour. Addition of 16% kevlar fabric, composite sample meets the performance requirement of NIJ0101.06 Level III-A. Since the maximum specific energy absorption was observed in Pure Kevlar samples and the adding of glass fibre increases the weight and Areal Density of the sample, further investigations need to be carried out to utilize the potential of glass fibre for ballistic applications.

Energy absorption characteristics of thin-walled steel tube filled with paper scraps

The specific energy absorption of a thin-walled tube can be improved by filler. This study examined the potential use of a cheaper biomass filler, paper scraps, to enhance the energy absorption characteristics of the structure while reducing its cost, compared to that with a traditional filler such as foam material. Quasi-static crushing tests and finite element simulations were performed by using the explicit non-linear finite element software LS-DYNA to determine the improvements to the mean crushing force and specific energy absorption of the steel tube when filled with different densities of paper scraps. The mean crushing force and specific energy absorption of the empty tube, the paper scraps, and thin-walled tube filled with paper scraps were determined, and corresponding numerical simulations were performed. The simulation and test results showed that the impact performance of tube filled with paper scraps was greatly improved when paper scraps density was 0.35 g/cm3. By optimizing paper scraps filling structure, a new structure that could further enhance the specific energy absorption was obtained. The optimal scheme could increase the specific energy absorption of Q345 steel tube by 11.35%.