low permittivity
Recently Published Documents


TOTAL DOCUMENTS

320
(FIVE YEARS 86)

H-INDEX

31
(FIVE YEARS 7)

Photonics ◽  
2021 ◽  
Vol 9 (1) ◽  
pp. 6
Author(s):  
Alexander W. Powell ◽  
Michal Mrnka ◽  
Alastair P. Hibbins ◽  
J. Roy Sambles

Designing a subwavelength structure with multiple degenerate resonances at the same frequency can vastly enhance its interaction with electromagnetic radiation, as well as define its directivity. In this work we demonstrate that such mode superposition or ‘stacking’ can be readily achieved through the careful structuring of a high-permittivity spherical shell, with either a metallic or a low permittivity dielectric (air) core. We examine the behaviour of these structures both as scatterers of plane wave radiation and as directive antennas. In the case where the core is metallic this leads to a superposition of the magnetic and electric modes of the same order, causing suppression of backscattering and unidirectional antenna emission. For an air core, an electric mode can superimpose with the next-highest order magnetic mode, the backscattered power is maximized and antenna emission is bidirectional. This is shown experimentally at microwave frequencies by observing the backscattering of core-shell spheres and we propose two antenna designs demonstrating different emission patterns defined by the superposition of multiple modes.


2021 ◽  
Vol 96 (12) ◽  
pp. 125866
Author(s):  
Anil Kumar Soni ◽  
Pushpa Giri ◽  
Gaurav Varshney

Abstract A technique is implemented for obtaining the high absorption over super-wideband (SWB) in a metal-free THz absorber. The multiple resonant modes with wide spectra are generated in a graphite-based resonator placed on a dielectric cavity merging of which provides the SWB response. The low permittivity dielectric slab sandwiched between the graphite sheet at its bottom and graphite resonator at its top acts as the Fabry–Perot cavity where absorption takes place. The high absorption rate of graphite in the THz regime can make it a suitable candidate for its utilization in implementing the broadband absorber. Thus, the molecular transition due to interaction of energy in graphite also provides the high absorption. The absorption bandwidth can further be enhanced by stacking of multiple layers in two different configurations of the proposed unit cell. The absorber maintains the polarization insensitivity due to symmetry and allows the high absorption for the electromagnetic wave incident up to the angle of more than 75 ° . The proposed absorber can be utilized in the THz electromagnetic shielding applications due to its SWB response.


Electronics ◽  
2021 ◽  
Vol 10 (23) ◽  
pp. 2961
Author(s):  
Kehan Zhang ◽  
He Du ◽  
Bo Luo ◽  
Ruikun Mai ◽  
Baowei Song ◽  
...  

Due to the natural low permittivity in vacuum, the voltage stresses on compensation capacitors and inductances in the capacitive power transfer (CPT) system are very high, which brings challenges to the design of CPT systems in practical applications. This paper used a three-cell structure analysis method for the CPT system to determine the optimal load for achieving the maximum power transfer or maximum efficiency transfer, through considering the maximum withstand voltage of the capacitor or inductor. A shielding layer with edge bending is designed to reduce the range of dangerous areas markedly. The simulation and experimental results verified the above conclusion. The prototype of the CPT system with transfer 3.1 kW across a 13 cm air gap and DC-DC transfer efficiency of 91.4% is built.


Materials ◽  
2021 ◽  
Vol 14 (21) ◽  
pp. 6266
Author(s):  
Xiaodi Dong ◽  
Mingsheng Zheng ◽  
Baoquan Wan ◽  
Xuejie Liu ◽  
Haiping Xu ◽  
...  

As the miniaturization of electronic appliances and microprocessors progresses, low-permittivity interlayer materials are becoming increasingly important for their suppression of electronic crosstalk, signal propagation delay and loss, and so forth. Herein, a kind of copolyimide (CPI) film with a “fluorene” rigid conjugated structure was prepared successfully. By introducing 9,9-Bis(3-fluoro-4-aminophenyl) fluorene as the rigid conjugated structure monomer, a series of CPI films with different molecular weights were fabricated by in situ polymerization, which not only achieved the reduction of permittivity but also maintained excellent thermodynamic stability. Moreover, the hydrophobicity of the CPI film was also improved with the increasing conjugated structure fraction. The lowest permittivity reached 2.53 at 106 Hz, while the thermal decomposition temperature (Td5%) was up to 530 °C, and the tensile strength was ≥ 96 MPa. Thus, the CPI films are potential dielectric materials for microelectronic and insulation applications.


Polymers ◽  
2021 ◽  
Vol 13 (19) ◽  
pp. 3254
Author(s):  
Mohd Aminudin Jamlos ◽  
Mohd Faizal Jamlos ◽  
Azri Alias ◽  
Mohamad Shaiful Abdul Karim ◽  
Wan Azani Mustafa ◽  
...  

This paper investigates the use of a Magnetite Polydimethylsiloxane (PDMS) Graphene array sensor in ultra-wide band (UWB) spectrum for microwave imaging applications operated within 4.0–8.0 GHz. The proposed array microwave sensor comprises a Graphene array radiating patch, as well as ground and transmission lines with a substrate of Magnetite PDMS-Ferrite, which is fed by 50 Ω coaxial ports. The Magnetite PDMS substrate associated with low permittivity and low loss tangent realized bandwidth enhancement and the high conductivity of graphene, contributing to a high gain of the UWB array antenna. The combination of 30% (ferrite) and 70% (PDMS) as the sensor’s substrate resulted in low permittivity as well as a low loss tangent of 2.6 and 0.01, respectively. The sensor radiated within the UWB band frequency of 2.2–11.2 (GHz) with great energy emitted in the range of 3.5–15.7 dB. Maximum energy of 15.7 dB with 90 × 45 (mm) in small size realized the integration of the sensor for a microwave detection system. The material components of sensor could be implemented for solar panel.


2021 ◽  
Author(s):  
Xiaomei Li ◽  
Pravash Bista ◽  
Amy Stetten ◽  
Henning Bonart ◽  
Maximilian Schür ◽  
...  

Abstract Water drops sliding down inclined planes are an everyday phenomenon and are important in many technical applications. Previous understanding is that the motion is mainly dictated by viscous and capillary forces. Here we demonstrate that, in addition to these forces, drops on hydrophobic surfaces are affected by self-generated electrostatic forces. In a novel approach to determine forces on moving drops we imaged their trajectory when sliding down a tilted surface and apply the equation of motion. We found that drop motion on low-permittivity substrates is significantly influenced by electrostatic forces. Sliding drops deposit a negative charge on the surface, which interact with the positively charged drops. We derive an analytical model to describe the force and validate it by numerical computations. The results indicate how to describe and facilitate drop motion in applications, such as in microfluidics, water management on car surfaces, and the creation of sliding drop electrical generators.


2021 ◽  
Vol 16 (2) ◽  
pp. 1-6
Author(s):  
William Da Silva Fonseca ◽  
Paula Ghedini Der Agopian

In this work, the influence of the underlap region on the electrical behavior of a SOI-nFinFET transistor has been studied with the purpose of radiation sensing. The analysis was performed by evaluating the impact of variations in the underlap region on the on-state current and by studying its sensitivity. The impact of the underlap region on the drain current and, consequently, on the devices’ sensitivity was explained by the analysis of series resistance, the fringing field and electron density. Considering the main impact of radiation in these devices, the study of sensitivity was also performed taking into consideration the variation of oxide trapped charges density. When applying the transistor to a harsh environment, the Underlapped FinFET showed to be a quite respectable radiation sensor, since the results performed with very good sensitivities when using long and narrow spacer oxide with low permittivity oxide. With thicker spacer oxide in the underlap region, the charge concentration makes the spreading field high enough to overcome the series resistance effect, which results in a less sensible device. Once presented the on-state current variation of the Underlapped FinFET, the study turns radiation-sensing purpose applicable using the excellent characteristics of this device, which is shown in detail throughout this work.


Sign in / Sign up

Export Citation Format

Share Document