hdpe pipe
Recently Published Documents


TOTAL DOCUMENTS

120
(FIVE YEARS 34)

H-INDEX

7
(FIVE YEARS 2)

Géotechnique ◽  
2021 ◽  
pp. 1-53
Author(s):  
Min Zhou ◽  
Ian D. Moore ◽  
Haitao Lan

Although structural response of pipelines has been studied in relation to different geohazards, few studies have focused on the behaviour of flexible pipeline joints. In this paper, the response of a bell and spigot joint in a 600 mm diameter lined-corrugated High Density Polyethylene (HDPE) pipe was investigated under the differential ground movements imposed using a facility that simulates a normal fault. Two experiments were undertaken in this facility. In the first experiment, the kinematic responses of the pipe joint (i.e. axial, shear displacements and rotational angles) were measured using Particle Image Velocimetry (PIV) and string potentiometers. Strains were also monitored using optical fibres. In the second experiment, the pipe was sealed and leakage of the joint was captured through monitoring of internal vacuum pressure of the pipe. The results show that axial shortening, rotational angle and shear displacement of the pipe joint increased with increasing fault offsets. The joint began to leak when axial shortening, rotational angle and shear displacement of the pipe joint were 0.65 mm, 0.44° and 3.40 mm, respectively, and the joint clearly lost its functionality when those values were 0.85 mm, 0.58° and 4.32 mm.


Energies ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 8008
Author(s):  
Michał Kubrak ◽  
Agnieszka Malesińska ◽  
Apoloniusz Kodura ◽  
Kamil Urbanowicz ◽  
Paweł Bury ◽  
...  

In pressurised pipeline systems, various water hammer events commonly occur. This phenomenon can cause extensive damage or even lead to a failure of the pumping system. The aim of this work is to experimentally re-examine the possibility of using an additional polymeric pipe, installed at the downstream end of the main pipeline, to control water hammer. A previous study on this topic investigated additional polymeric pipes connected to the hydraulic system with a short joint section of the same diameter as the main pipeline. In the current research, a different method of including an additional pipe was considered which involved connecting it with a pipe of a smaller diameter than the main pipeline. Three additional HDPE pipes, with different volumes, were investigated. The performance of the devices was studied for hydraulic transients induced by both rapid and slow, manual valve closures. Experimental results show that the additional polymeric pipe can provide significant pressure surge damping during rapid water hammer events. As the valve closing time lengthens, the influence of the additional pipe on the maximum pressure increase is reduced. The additional HDPE pipe does not provide notable protection against hydraulic transients induced by slow valve closure in terms of reducing the first pressure peak. No relationship between the volume of the additional pipe and the damping properties was noticed. The observed pressure oscillations were used to evaluate a one-dimensional numerical model, in which an additional pipe is described as a lumped parameter of the system. The viscoelastic properties of the device were included using the one element Kelvin–Voigt model. Transient flow equations were solved with the implicit method of characteristics. Calculation results demonstrate that this approach allows one to reasonably reproduce unsteady flow oscillations registered during experiments in terms of the maximum pressure increase and pressure wave oscillation period.


Author(s):  
Rachid Ketrane ◽  
Celia Yahiaoui

Abstract In Algeria, high-density polyethylene (HDPE) is widely used in drinking water pipes. This study is focused on the precipitation of calcium carbonate, a major constituent of scale, from calcocarbonically pure (CCP) water in HDPE pipe. Studying scaling in natural conditions is very difficult because it occurs over many years. For this, accelerated scaling is caused by the degassing CO2 dissolved in water. The kinetic study has shown that the germination time and the critical pH decrease with the hardness (30, 40 and 50 °f) and temperature (30, 40 and 50 °C) of water. On the other hand, scaling process efficiency (η) and the supersaturation coefficient (Ωcal) of CaCO3 increase with these parameters. The CaCO3 precipitation occurs both in solution and on walls of HDPE. By the weighing method, it is shown that the deposit mass increases with hardness and temperature. Calcium carbonate precipitates much more in homogeneous phase than in heterogeneous one. The study also showed that heterogeneous nucleation on HDPE is much less important than on PA, PVC, chrome and Inox. These measurements are supported by the characterization of X-ray diffraction deposits and by scanning electron microscopy, which recognizes that the precipitate obtained consists mainly of calcite.


2021 ◽  
Vol 146 ◽  
pp. 106743
Author(s):  
Yuqing Xia ◽  
Nan Jiang ◽  
Chuanbo Zhou ◽  
Xianzhong Meng ◽  
Xuedong Luo ◽  
...  

2021 ◽  
pp. 089270572110108
Author(s):  
Christopher Chukwutoo Ihueze ◽  
Christian Emeka Okafor ◽  
Sylvester Nnaemeka Obuka ◽  
Jibrilla Abdulrahman ◽  
Uchendu Onwusoronye Onwurah

This paper focused on the establishment of performance level and cost of plantain fibers reinforced High Density Polyethylene (HDPE) matrixes as gas pipeline material using pressure containment of the new materials as performance criterion. The cost of modified plantain fibers, the cost of plantain fibers reinforced HDPE (PFRHDPE) and the cost of PFRHDPE master batch (HDPE resin + plantain fiber particles + stabilizer, plasticizer) for pipes extrusion production and pipelines fittings injection productions were established. The burst pressure evaluated for available standard outside diameter ratio (SDR) using the ultimate tensile strength of PFRHDE is very much greater than the standard SDR design pressures even when the temperature derating factors were applied. The Maximum Allowable Operating Pressure (MAOP) of PFRHDPE and induced stresses of pressurized pipes established indicated that the new material is suitable for pipeline design for natural gas and liquid petroleum (LPG) lines. The PFRHDPE developed has better specific properties than the conventional steel and HDPE pipe material in terms of yield strength, elastic modulus and density of the new material. But in terms of cost, steel and HDPE has approximate desirability for selection with PFRHDPE. The energy required to manufacture and process steel products is about 480 MJ/m2, while that of plastics is about 320 MJ/m2. The study further established that PFRHDPE can be applied in the design of oil and gas gathering, transportation and distribution lines.


2021 ◽  
Vol 15 (56) ◽  
pp. 115-122
Author(s):  
Abdelmalek Regad ◽  
Djebara Benzerga ◽  
Habib Berrekia ◽  
Abdelkader Haddi ◽  
Nourredine Chekhar

The good management of drinking water begins with a supply network, with a low rate of leakage. Currently, the pipes used in the water transport system are mainly made of polymeric materials, such as HDPE. The corrosion degradation of this type of pipe has received a lot of attention from the drinking water supply companies. It is therefore important to understand the effect of pressure on an HDPE pipe with a surface defect. To answer this problem, we will first study the mechanical behavior at failure of HDPE pipes in the presence of a surface defect using a finite element method. For the rehabilitation of pipe in presence of surface defect, we try to use a new composite. This new laminated composite is reinforced with a natural organic load. It is obtained from a laminated composite woven by incorporating a natural non-polluting organic load (granulates of date cores) which becomes hybrid composite. The new economical hybrid composite material is made of an organic matrix containing methyl methacrylate, a woven reinforcement including a reinforcing glass fiber and a fabric perlon having an absorbing role. The textile reinforcement made up of several folds reinforcing laid out according to the orientations (90, 452, and 0). A numerical simulation with the ANSYS Workbench software is carry out  to study the behavior of the HDPE pipe with surface defect and with defect repaired by the new hybrid composite material in the form of rings to consolidate the cracked area of ​​the tube. The numerical results will allow us to decide on a real practical use of the new hybrid composite.


Sign in / Sign up

Export Citation Format

Share Document