groove structure
Recently Published Documents


TOTAL DOCUMENTS

128
(FIVE YEARS 53)

H-INDEX

11
(FIVE YEARS 3)

2022 ◽  
Vol 148 ◽  
pp. 107795
Author(s):  
Yilin Shan ◽  
Xianmin Zhang ◽  
Gengchao Chen ◽  
Kai Li

Author(s):  
Zhengjing Shen ◽  
Wei Han ◽  
Yiming Zhong ◽  
Bo Luo ◽  
Rennian Li ◽  
...  

Previous work has shown that performance and internal flow characteristics of a centrifugal pump can be significantly improved with grooved volute casing (GVC). However, it has been found that the selection of the design parameters of the groove structure also has a direct impact on the performance output, internal flow pressure pulsation and erosion wear characteristics of the overflow components of centrifugal pump, so it is necessary to further analyze the design rules of the groove structure parameters. In this study, we first investigated the influence of the number of grooves on the head, efficiency and unsteady pressure pulsation characteristics of the internal flow field of the centrifugal pump, and on this basis, the correlation between different particle parameters and the erosion wear of key overflow components under the conditions of solid–liquid two-phase flow were also studied, and the erosion wear characteristics of the inner wall of the volute casing of centrifugal pump with GVC and original volute casing (OVC) structures were compared. This research leads to the conclusion that when the number of grooves is 3, the groove structure has the least influence on the performance of the centrifugal pump, and the overall change of the performance curve is more stable. Additionally, the pressure pulsation at each monitoring point of the GVC under the same flow condition is smaller, and when the number of grooves increases, the pressure pulsation amplitude also decreases. When the number of grooves is 3, the GVC shows a more significant flow improvement effect under all flow conditions. Based on the improvement of the groove structure on the flow stability, the particle motion behavior can be affected at the same time, so that the pump with GVC can mitigate the erosion wear of the inner wall of the volute casing under the solid–liquid two-phase flow conditions, which improves the critical performance and service life of the key overflow components of the pump.


2022 ◽  
Vol 243 ◽  
pp. 110280
Author(s):  
Yu-bo Hu ◽  
Yong-gang Yu ◽  
Xin-wei Zhang
Keyword(s):  

Water ◽  
2021 ◽  
Vol 14 (1) ◽  
pp. 36
Author(s):  
Jiyang Qi ◽  
Yue Qi ◽  
Qunyan Chen ◽  
Fei Yan

In this study, the drag reduction effect is studied for a cylinder with different V-groove depths on its surface using a k-ω/SST (Shear Stress Transport) turbulence model of computational fluid dynamics (CFD), while a particle image velocimetry (PIV) system is employed to analyze the wake characteristics for a smooth cylinder and a cylinder with different V-groove depths on its surface at different Reynolds numbers. The study focuses on the characteristics of the different V-groove depths on lift coefficient, drag coefficient, the velocity distribution of flow field, pressure coefficient, vortex shedding, and vortex structure. In comparison with a smooth cylinder, the lift coefficient and drag coefficient can be reduced for a cylinder with different V-groove depths on its surface, and the maximum reduction rates of lift coefficient and drag coefficient are about 34.4% and 16%, respectively. Otherwise, the vortex structure presents a complete symmetry for the smooth cylinder, however, the symmetry of the vortex structure becomes insignificant for the V-shaped groove structure with different depths. This is also an important reason for the drag reduction effect of a cylinder with a V-groove surface.


2021 ◽  
Vol 2137 (1) ◽  
pp. 012012
Author(s):  
Weigao Qiao ◽  
Zhanxi Zhang ◽  
Dong Lu ◽  
Lei Yu

Abstract To effectively improve the safety of battery boxes in side collision of electric vehicles, two measures are proposed: Firstly spread the boss evenly around the battery box. Secondly the upper and lower parts of the battery box are matched with the convex heads and groove structure. The finite element models of the battery boxes before and after the optimization, the vehicle and the movable barrier are established in this paper. According to the collision regulations, the side collision simulation of the vehicle body is carried out. The changes of the stress, deformation and lateral acceleration of the battery boxes are analyzed. The effectiveness of the measures is verified. The extrusion models of the battery boxes are established. The deformation and the changes of the internal energy of the battery boxes are analyzed. The effectiveness of the measures is verified again.


2021 ◽  
Vol 11 (23) ◽  
pp. 11354
Author(s):  
Ruichuan Li ◽  
Xinkai Ding ◽  
Jianghai Lin ◽  
Feng Chi ◽  
Jikang Xu ◽  
...  

In this study, a structurally improved spool was designed. The diameter of one side of the spool stem was reduced, making the spool stem into a rounded table shape. A triangular groove was circumscribed on the step and on the same side. After liquid flow was guided through the triangular groove, the flow direction changed. A flow component in the negative direction was generated, which reversely impacted the liquid flow in the positive direction. The liquid flow angle at the outlet increased; that is, jet angle increased and flow force decreased. The simulation results show that, increasing the depth, H, of the triangular groove has a positive effect on flow-force compensation and was conducive to the stability of the valve core. Properly increasing the groove’s bottom diameter, D1, of the triangular groove was conducive to the stability of the spool, but when D1 was too large, the flow force increased. The experimental results are consistent with the simulation results, which proves that the improved structure can effectively reduce the flow force of the spool.


2021 ◽  
Vol 11 (1) ◽  
Author(s):  
S. R. Shelley ◽  
J. G. Beadle ◽  
A. P. Hibbins ◽  
J. R. Sambles

AbstractThe acoustic surface modes supported by a partly covered periodic meander groove structure formed in an assumed perfectly rigid plate are investigated. This allows one to create a slower acoustic surface wave than can be achieved with the same uncovered meander structure. By changing the size of the uncovered section the phase and group speeds can be tuned. When the uncovered section of the meander structure is centred along the grooves then the distance along the grooves between neighbouring holes is the same on both sides of the structure so no band gap is observed at the first Brillouin zone boundary due to glide symmetry. This then gives quite linear dispersion. As the uncovered section’s position is moved away from the centre of the meander structure a band gap opens at the Brillouin zone boundary.


Sign in / Sign up

Export Citation Format

Share Document