Joining sheets made from dissimilar materials by hole hemming

This research work presents a new joining process based on the hemming process for attaching sheets made from dissimilar materials with very different mechanical properties. The process is termed ‘hole hemming’ and consists in producing a mechanical interlock between pre-drilled holes which can be made anywhere on the sheets. The process is carried out in a two-stage operation including flanging the hole of an outer sheet and bending the flange over the hole of an inner sheet. First, the joining stages and the required tools are designed. Then, the joining of DP780 steel and AA6061-T6 aluminium alloy sheets, which are applied to manufacture lightweight structures in the automotive industries, is investigated using finite element analysis. Results show that the hole hemming process is able to successfully join these materials without fracture. The hole-hemmed joint withstood the maximum forces of 2.5 and 0.5 kN in single-lap shear and peel tests, respectively, and failed with hole bearing mode which is known as a gradual failure mode. The results demonstrate the applicability of the hole hemming process for joining dissimilar materials.

Numerical Simulation of Friction Stir Spot Welding of Aluminium-6061 and Magnesium AZ-31B

Friction stir spot welding process is a solid state joining process which has attracted great attention due to its ability to join low melting point light weight alloys such as aluminium and magnesium with high efficiency. In order to understand the complex thermo-mechanical joining process involved with friction stir spot welding, a numerical simulation study was done using ABAQUS finite element software. The simulation primarily aims to interpret the effect of a set of process parameters and tool geometry on the workpiece plates. Johnson-Cook damage criteria model was used to obtain the stress and strain distribution on the workpiece consisting of aluminium 6061 and magnesium AZ-31B placed in a lap configuration. Temperature distribution of the workpiece was obtained by simulating a penalty based frictional contact between the tool and the plate. The thermal results showed that the maximum temperatures attained were significantly lower than the melting points of the base materials indicating that the material mixing and joining occurred as a result of superplastic deformation process instead of melting. Change in material flow behaviour was also observed by the model as pin and shoulder geometries changed.

Investigation of the influence of varying tumbling strategies on a tumbling self-piercing riveting process

The increasing demands for the reduction of carbon dioxide emission require intensified efforts to increase resource efficiency. Especially in the mobility sector with large moving masses, resource savings can contribute enormously to the reduction of emissions. One possibility is to reduce the weight of the vehicles by using lightweight technologies. A frequently used method is the implementation of multi-material systems. These consist of dissimilar materials such as steel, aluminium or plastics. In the production of these systems, the joining of the different materials and geometries is a central challenge. Due to the increasing demands on the joints, the challenges for the joining processes itself are also increasing. Since conventional joining processes are rather rigid and can only react to a limited extent to disturbance variables or changing process variables, new methods and technologies are required. A widely used conventional joining method with these properties is self-piercing riveting. Because of the rigid tool combination and the fact that the rivet geometry that can be used is related to the tools, the joining of multi-material systems requires tool and rivet changes during the process. In order to extend the process window of joining with self-piercing rivet elements, the process is enhanced with a tumbling kinematic of the punch. The integration of tumbling results in a significant increase in the adjustable process parameters. This enables a higher material flow control in the joining process through a specific tumbling strategy. The materials investigated are a steel and an aluminium alloy, which differ significantly in their mechanical properties and have many applications in automotive engineering, especially for structural car body components. The steel material is a galvanized HCT590X+Z dual-phase steel, which is characterised by a low yield strength, combined with high tensile strength and a good hardening behaviour. The aluminium alloy is an EN AW-6014. The precipitation-hardening alloy consists of aluminium, magnesium and silicon with a high strength and energy absorption capability. The objective of this work is to obtain a fundamental knowledge of the new tumbling self-piercing riveting process. With different mechanical properties and different sheet thicknesses of the joining partners, the influences of these parameters on the tumbling strategy of the riveting process are analysed. Such a tumbling strategy is based on the tumbling angle, the tumbling onset and the tumbling kinematics. These parameters are investigated in the context of the work for selected combinations of multi-material systems consisting of HCT590X+Z and EN AW-6014. With the variation of the parameters, the versatility of the process can be investigated and influences of the tumbling on the self-piercing riveting process can be identified. To illustrate the results, force–displacement curves from the joining process of the individual joints are compared and the geometry of the rivet undercut and rivet heads are geometrically measured. Furthermore, micrographs allow the analysis of the characteristic joint parameters interlock, residual sheet thickness and end position of the rivet head.

Joining of CFRT-steel hybrid parts via hole-forming and subsequent pin caulking

In times of increasing global warming, the awareness of the necessity for significant CO2 reduction is growing. Especially in the transport and aerospace sector, lightweight construction has potential to achieve emission reduction goals by reducing the overall vehicle weight. Thereby, adding lightweight fibre-reinforced composites to materials such as steel and aluminium is used to achieve weight savings. Furthermore, continuous-fibre-reinforced thermoplastics (CFRTs) begin to replace more traditional thermoset thermoplastics due to their easier bulk production and uncomplicated storage. Hybrid parts often consist of a CFRT and a higher strength metal component. Here, the joining process poses the main challenge, due to different chemical and physical properties of the components. In the current state of the art, riveted and bolted joints are commonly used, leading to increased weight due to auxiliary elements and requiring precise bolt holes often destroying load-bearing fibres. Joining with cold formed pin structures is an innovative and versatile joining process, which avoids the need for auxiliary elements. These pins are subsequently inserted in warm formed holes in the CFRT component and then caulked to create a form-fitting hybrid joint. To obtain a fundamental understanding of this joining process, hole-forming and pin-caulking, are investigated in this study. First, the hole-forming with IR-radiation is investigated with regard to suitable process parameters and resulting fibre morphology. The formed holes are consequently mechanically characterized. Second, the caulking-process is investigated by iteratively upsetting a pin and subsequently measuring the geometry. Based on these findings two different suitable caulking degrees are defined and samples for mechanical as well as microscopic investigations are manufactured. The created joints are first investigated via micro-sections and reflected light microscopy to identify possible damage in the CFRT component, which can result from the pin caulking process. Second, a mechanical characterisation under shear load as well as pin extraction loads normal to the sample surface is conducted and the normal load tests are compared with the bearing strength of CFRT samples.

A contribution on versatile process chains: joining with adaptive joining elements, formed by friction spinning

Nowadays, manufacturing of multi-material structures requires a variety of mechanical joining techniques. Mechanical joining processes and joining elements are used to meet a wide range of requirements, especially on versatile process chains. Most of these are explicitly adapted to only one, specific application. This leads to a less flexibility process chain due to many different variants and high costs. Changes in the boundary conditions like sheet thickness, or layers, lead to a need of re-design over the process and thus to a loss of time. To overcome this drawback, an innovative approach can be the use of individually manufactured and application-adapted joining elements (JE), the so-called Friction Spun Joint Connectors (FSJC). This new approach is based on defined, friction-induced heat input during the manufacturing and joining of the FSJC. This effect increases the formability of the initial material locally and permits them to be explicitly adapted to its application area. To gain a more detailed insight into the new process design, this paper presents a detailed characterization of the new joining technique with adaptive joining elements. The effects and interactions of relevant process variables onto the course and joining result is presented and described. The joining process comprises two stages: the manufacturing of FSJC from uniform initial material and the adaptive joining process itself. The following contribution presents the results of ongoing research work and includes the process concept, process properties and the results of experimental investigations. New promising concepts are presented and further specified. These approaches utilize the current knowledge and expand it systematically to open new fields of application.

Microstructure and Mechanical Properties of Welded Joints of 1.4462 Duplex Steel Made by the K-TIG Method

K-TIG (Keyhole Tungsten Inert Gas) method is a new, emerging welding technology that offers a significant acceleration of the joining process, even for very thick plates. However, its potential for welding of certain materials is still unknown. Particularly challenging are duplex steels as this technology does not allow the use of a filler material, which is crucial for these steels and for weld joint microstructure adjustment. In order to demonstrate the suitability of this technology for single-pass welding of 1.4462 duplex steel detailed studies of the microstructure of the weld joints obtained for different linear energies were carried out and discussed with respect to their mechanical properties. According to the results obtained, the heat-affected zone (HAZ) shows a microstructure similar to the HAZ of duplex steel welded with the traditional TIG multi-pass methods. However, the weld, due to the lack of filler material, had a microstructure different to that typical for duplex steel welded joints and was also characterized by an increased content of ferrite. However, all joints, both in terms of microstructure and mechanical properties, met the requirements of the relevant standards. Moreover, the K-TIG process can be carried out in the linear energy range typical of duplex steel welding, although further optimization is needed.

Computed tomography investigation of the material structure in clinch joints in aluminium fibre-reinforced thermoplastic sheets

Recent developments in automotive and aircraft industry towards a multi-material design pose challenges for modern joining technologies due to different mechanical properties and material compositions of various materials such as composites and metals. Therefore, mechanical joining technologies like clinching are in the focus of current research activities. For multi-material joints of metals and thermoplastic composites thermally assisted clinching processes with advanced tool concepts are well developed. The material-specific properties of fibre-reinforced thermoplastics have a significant influence on the joining process and the resulting material structure in the joining zone. For this reason, it is important to investigate these influences in detail and to understand the phenomena occurring during the joining process. Additionally, this provides the basis for a validation of a numerical simulation of such joining processes. In this paper, the material structure in a joint resulting from a thermally assisted clinching process is investigated. The joining partners are an aluminium sheet and a thermoplastic composite (organo sheet). Using computed tomography enables a three-dimensional investigation that allows a detailed analysis of the phenomena in different joining stages and in the material structure of the finished joint. Consequently, this study provides a more detailed understanding of the material behavior of thermoplastic composites during thermally assisted clinching.

Laser Transmission Welding of Aluminum Film Coated With Heat Sealable Co-Polyester Resin With Polypropylene Films For Applications In Food & Drug Packaging

The present work deals with the high-power diode laser joining process of aluminum films coated with a polyester resin with polypropylene (PP) films. The first part of the work focused on analyzing the coating process of aluminum films with a polyester resin, using an automatic applicator. The second part of the work was focused on the analysis of the laser joining process of coated aluminum films with plastic counterparts made of PP. Different thicknesses and colors of the PP parts were tested in order to analyze the joining process under a wide range of different conditions. The experimental plan involved the study of the influence of the laser joining parameters, in particular the scanning speed and beam power, on the joints. The joints between aluminum and PP films were subsequently tested by means of tensile and peel-off tests. The results allowed the detection of the best processing conditions, stating the high potential of laser systems in the joining process of aluminum and PP films for food packaging applications.

Friction Stir Welding of Thick Plates of 4Y3Gd Mg Alloy: An Investigation of Microstructure and Mechanical Properties

Applications of non-ferrous light metal alloys are especially popular in the field of aerospace. Hence it is important to investigate their properties in joining processes such as welding. Solid state joining process such as friction stir welding (FSW) is quite efficient for joining non-ferrous alloys, but with thick plates, challenges increase. In this study, Mg alloy plates of thickness 11.5 mm were successfully welded via single-pass FSW. Due to the dynamic recrystallization, grain size in the stir zone was reduced to 16 µm which is ≈15 times smaller than the parent material. The optimized rotational speed and traverse speed for optimum weld integrity were found to be 710 rpm and 100 mm/min, respectively. A sound weld with 98.96% joint efficiency, having an Ultimate Tensile Strength (UTS) of 161.8 MPa and elongation of 27.83%, was accomplished. Microhardness of the nugget was increased by 14.3%.

Numerically modelled study of the plunge stage in friction stir spot welding using multi-tiered mesh partitions

Friction stir spot welding is a solid-state joining process that has attracted significant attention particularly in the field of joining of lightweight, low melting alloys. These materials include alloys of Aluminium and Magnesium amongst many others which are of great importance to the aerospace and the automobile industries. The friction stir spot welding is a complex thermo-mechanical multiphysics phenomenon and is currently a field of intense research. The motivation of the current study is to understand this complex behaviour of the joining process by simulating it in the ABAQUS CAE environment. In the friction stir spot joining technique, the plunge stage is identified as the critical stage of operation as it involves a highly transient and dynamic zone for material and temperature flows. The plunge stage was studied in detail using the finite element based model. The plasticity of the material was simulated by the Johnson-Cook material model while the frictional heat generation was captured by applying a penalty-based frictional contact between the rotating tool and the workpiece contact surfaces. Considering the reasonable assumptions made, the results obtained by the numerical simulation model were found to agree with the past experimental and numerically modelled studies.