Recent Advances in Biomass-Based Waste Materials for the Removal of Chromium (VI) from Wastewater: A Review

Hexavalent chromium (Cr(VI)) is a critical pollutant with high toxicity, even at trace concentrations. Cr(VI) is possibly carcinogenic and mutagenic and can produce serious health issues. Hence, it is necessary to remove Cr(VI) from the water before releasing it into the environment. Currently, numerous removal techniques were used. Adsorption is the best method compared to others because it is simple, cheap, highly efficient, and can be used in water having trace concentrations of contaminants. Biomass-based waste materials (BMWs) are found as far better adsorbents than commercially and other available adsorbents. In this study, the existing Cr(VI) removal techniques are reviewed and, a broad range of current research studies of Cr(VI) removal from water by using BMWs are evaluated. This review can be helpful to develop a more efficient, cheap, reliable, and environmentally benign bio-adsorbent. It is obvious after the literature review given herein that BMWs exhibited potential adsorbents for the removal of Cr(VI). Also, the chemically modified adsorbents exhibited a higher adsorption capacity than unmodified adsorbents.

Poly(amidoamine) dendrimer modified superparamagnetic nanoparticles as an efficient adsorbent for Cr(VI) removal: Effect of high-generation dendrimer on adsorption performance

Heavy metal ions pollution is one of the most dangerous and critical threats to human health and environment. In this work, three different generations of PAMAM dendrimer decorated on magnetic Fe 3 O 4 composites (Fe 3 O 4 @SiO 2 –G1, Fe 3 O 4 @SiO 2 –G3, Fe 3 O 4 @SiO 2 –G5) were fabricated and characterized by FTIR, XRD, TEM, and TGA. The obtained composites were used for Cr(VI) removal. Batch adsorption studies showed that the adsorption reached equilibrium within 60 min, and the optimal pH was 3.0. The result of adsorption kinetics was simulated by the pseudo–second-order model. The adsorption equilibrium isotherm was well fitted with the Langmuir adsorption model. Furthermore, thermodynamics calculations revealed that the adsorption process was endothermic and spontaneous. Importantly, adsorption capacity of Cr(VI) obey the sequence of Fe 3 O 4 @SiO 2 –G1＜Fe 3 O 4 @SiO 2 –G5＜Fe 3 O 4 @SiO 2 –G3, 3 generation of PAMAM (3G) is the optimal for adsorption capacity of Cr(VI). The maximum theoretical Cr(VI) adsorption capacity ( q m ) of Fe 3 O 4 @SiO 2 –G3 was 334.45 mg/g, and removal ration remained above 89.5% after five cycles of adsorption–desorption. Thus, Fe 3 O 4 @SiO 2 –G3 is predicted to be an efficient adsorbent for the adsorption of Cr(VI) from aqueous solution, and the obtained results can help in the generation optimization during fabrication of dendrimer modified adsorbents.

Optimizing modified rice bran for treating aqueous solutions polluted by Cr (VI) ions: isotherm and kinetics analyses

This study investigated the possibility and efficiency of absorbing chromium (VI) (Cr [VI]) ions from the polluted solutions by employing the chemically modified adsorbents (alkali, biochar, and acid rice bran), focusing on the possible impacts of the solution’s pH values, adsorbent’s dosages, concentrations, and contact times. The colori-metric method was used for Cr determination by employing an ultraviolet/visible spectrophotometer. The scanning electron microscope and Fourier transform infrared spectroscopy were used to analyze the characteristics of the modified adsorbents. The findings indicated that the optimized acid, biochar, alkali, and unmodified rice bran removal efficiency for Cr (VI) were 94.50%, 94.27%, 88.60%, and 90.18%, respectively. The increase of adsorbent dosage up to 2 g/L led to a rise in removal effectiveness (82.06%). Furthermore, the highest removal efficiency was obtained (94%) at the pH of 2.0, the contact duration of 100 min, Cr (VI) concentration of 50 mg/L, and dosage of 2 g/L, which was statistically the optimal condition for the modified rice bran. The adsorption kinetics was agreeably suited to pseudo-second-order, whereas the Freundlich isotherm equation was also suitably expounded the study’s findings. The findings implied that the acid and biochar rice bran performed remarkably in the reme-diation of the wastewater compared with alkali rice bran for reuse for industrial, agricultural, and environmental purposes.

The Dependency of Kinetic Parameters as a Function of Initial Solute Concentration: New Insight from Adsorption of Dye and Heavy Metals onto Humic-Like Modified Adsorbents

Kinetics parameters are the essential issue in the design of water treatment systems for pollutants uptake. Though numerous studies have identified the boundary conditions that exert influence on the kinetics parameters, the influence of the dynamic initial solute concentration (C0) to the kinetic parameters generated from fitting kinetics model to experimental data has not been investigated thoroughly. This study revealed a change in the kinetics parameter value due to changes in the adsorption mechanism as an effect of dynamic C0. It was observed that at higher C0 the adsorbed solute at equilibrium (qe) increases and it takes longer time to reach equilibrium. As a result, the kinetics rate constant (k) calculated from adsorption reaction model (Lagergren, Ho, Santosa, and RBS) was decreased. In general, Ho model exhibit higher correlation coefficient value (R2) among the other model at low C0. At high C0, Ho’s R2 tend to decrease while the Lagergren and RBS’s R2 was increased. The amendment mechanism from external mass transport to intra-particle diffusion as a rate limiting step was evidenced by Boyd and Weber-Morris kinetics model. Further, the physicochemical properties of the adsorbent used in this work: chitin and Fe3O4 modified horse dung humic acid (HDHA-Fe3O4 and HDHA-Ch, respectively) with the solute: Pb(II), Methylene Blue (MB), and Ni(II) was deeply discussed in this paper. The outcomes of this work are of prime significance for effective and optimum design for pollutant uptake by adsorption equipment. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0).

SORPTION OF BISMUTON (III) IONS FROM AQUEOUS SOLUTIONS BY SILICAS MODIFIED BY ORGANIC REAGENTS

In current paper, adsorbents based on silica L 40/100 modified with 4-(2-pyridylazo)resorcinol, 1-(2-pyrylazo)naphthol‑2, pyrocatechol violet and sodium N, N‑diethyldithiocarbamate were obtained. Adsorbents were modified by non-covalent immobilization of organic analytical reagents on the silica surface. It is noted that the preparation of such adsorbents is fast and easy to manufacture. The conditions of Bismuth (III) adsorption from dilute aqueous solutions by the proposed adsorbents are studied and optimized. The optimal values of the medium acidity for the effective Bismuth (III) preconcentration by the proposed adsorbents based on silica modified with organic analytical reagents have been established. It is shown that the use of modified silicas allows efficient (95–98%) removal of Bismuth (III) from dilute aqueous solutions. Under optimal adsorption conditions, the capacity of modified adsorbents is determined. It is established that the modification of silica leads to a significant (2–3 times) increase in the capacity of the obtained sorbents by Bismuth (III) in comparison with the unmodified silica, which is associated with the processes of complexation on the surface. The desorption of Bismuth (III) from the surface of unmodified and modified silicas by solutions of mineral acids has been studied. It is shown that Bi(III) is quantitatively desorbed from the surface of unmodified silicas by solutions of sulfuric and nitric acids, and in the case of modified silicas the degree of desorption is small and does not exceed 35%. The data obtained can then be used to develop a test system for determination of Bismuth (III) via corresponding colorimetric scales or for quantitative solid phase extraction and adsorption-spectroscopic quantification of Bismuth (III) in some real samples.

Modified Chitosan Forms for Cr (VI) Removal

The forms of utility in the wastewater treatment of chitosan-based adsorbents acquired from natural substances have attracted numerous attentions in recent years. The use of chitosan modified adsorbents for removal of the chromium has aroused great interest. When chitosan-based modified adsorbents are considered, they have got large amount of an amino (-NH2) and hydroxyl (-OH) functional groups. Such adsorbents display that they have high activity and therefore they may be extensively utilized in wastewater treatment plants to cast off chromium. In this chapter, the utility outcomes of chitosan-based substances will be explained after applying different parameters to remove Cr (VI) from the aqueous surrounding with the information obtained the use of batch adsorption systems. Application of various chitosan-based adsorbents for Cr (VI) removal application will be demonstrated in a detailed way and they will be discussed within the textual content.