Research on failure mode and ultimate bearing characteristics of the single pile foundation in soft clay

Author(s):  
B Li ◽  
Z Liu
Structures ◽  
2021 ◽  
Vol 29 ◽  
pp. 1229-1241
Author(s):  
Swagata Deb Roy ◽  
Animesh Pandey ◽  
Rajib Saha

2019 ◽  
Vol 5 (4) ◽  
pp. 922-939 ◽  
Author(s):  
Anis Abdul Khuder Mohamad Ali ◽  
Jaffar Ahemd Kadim ◽  
Ali Hashim Mohamad

The objective of this article is to generating the design charts deals with the axially ultimate capacity of single pile action by relating the soil and pile engineering properties with the pile capacity components. The soil and are connected together by the interface finite element along pile side an on its remote end.  The analysis was carried out using ABAQUS software to find the nonlinear solution of the problem. Both pile and soil were modeled with three-dimensional brick elements. The software program is verified against field load-test measurements to verify its efficiency accuracy. The concrete bored piles are used with different lengths and pile diameter is taken equals to 0.6 m. The piles were installed into a single layer of sand soil with angles of internal friction (20° t0 40°) and into a single layer of clay soil with Cohesion (24 to 96) kPa.  The getting results showed that for all cases study the total compression resistance is increased as pile length increased for the same property of soil, also illustrious that the total resistance of same pile length and diameter increased as the soil strength increasing. In addition, the same results were obtained for the end bearing resistance, skin resistance and tension capacity. Design charts were constructed between different types of soil resistance ratio and the pile length/diameter ratio (L/D) for all cases of study. One of improvement found from these curves that it is cheaply using piles of larger diameter than increasing their lengths for dense sand and to increasing piles lengths for loose sand. Moreover, it is inexpensively using piles of larger length in soft clay soil than increasing their diameter and piles of larger diameter in firm and stiff clay soils than increasing their length.


2022 ◽  
Vol 119 ◽  
pp. 103032
Author(s):  
Lei Song ◽  
Hongfen Zhao ◽  
Jinhui Li ◽  
Qingjie Yang

2019 ◽  
Vol 136 ◽  
pp. 04061
Author(s):  
Yazhou Li ◽  
Li Dong

The offshore wind turbine single pile foundation structure is simple and easy to install, but in the earthquake environment, large horizontal displacement is easy to occur, which affects the safe operation of offshore wind turbines. For this reason, the bearing characteristics and influencing factors of large-diameter single-pile offshore wind power under earthquake load are analyzed. The Mohr-Coulomb model is used as the model. The ABAQUS is used to construct the large-scale single-pile finite element model of offshore wind power. Loads and analysis of bearing characteristics and influencing factors of large-diameter single-pile offshore wind power under seismic loading. It is found that the increase of pile foundation depth will significantly reduce the horizontal displacement at the top of single pile. After increasing to a certain extent, it has no significant effect on the development of horizontal deformation of large diameter single pile; with the increase of pile diameter and wall thickness, The deformation of large diameter single pile foundation is reduced, but the influence of the pile foundation thickness on the horizontal deformation of the large diame-ter single pile foundation is no longer significant.


Author(s):  
Qilin Yin ◽  
Jinjin Zhai ◽  
Sheng Dong

The overall bearing capacity of a jack-up rig under horizontal load is conducted using finite element models that consider the deck–foundation–soil interaction. In these models, the simplified horizontal load acts on the deck and increases until the platform loses its stability. The effects of the self-weight of the platform W and load direction α on the ultimate horizontal bearing capacity Hult are investigated, and W- Hult failure envelopes under different α conditions are obtained. Two typical seabed types, including the double-layer seabed of sand overlying soft clay and the single-layer seabed of sand, are considered. The results show that a critical self-weight Wcritical exists in the double-layer seabed. Based on Wcritical, the failure of the platform presents two different modes. When W <  Wcritical, the windward leg is pulled up, and Hult increases with the increase in W. When W >  Wcritical, the failure mode is the leeward leg or legs puncturing the bearing sand layer, and Hult decreases with the increase in W. In the single-layer seabed, the failure mode is the windward leg being pulled up, and Hult increases with the increase in W throughout the whole range. The W- Hult envelopes in these two types of seabeds are basically the same when W <  Wcritical.


Sign in / Sign up

Export Citation Format

Share Document