scholarly journals Small Hall Effect Thruster with 3D Printed Discharge Channel: Design and Thrust Measurements

Aerospace ◽  
2021 ◽  
Vol 8 (8) ◽  
pp. 227
Author(s):  
Ethan P. Hopping ◽  
Wensheng Huang ◽  
Kunning G. Xu
Keyword(s):  
3D Printing ◽  
Hall Effect ◽  
Discharge Channel ◽  
Low Cost ◽  
Hall Thrusters ◽  
Hall Effect Thruster ◽  
Sustained Operation ◽  
3D Printed ◽  
Multiple Materials ◽  
And Performance

This paper presents the design and performance of the UAH-78AM, a low-power small Hall effect thruster. The goal of this work is to assess the feasibility of using low-cost 3D printing to create functioning Hall thrusters, and study how 3D printing can expand the design space. The thruster features a 3D printed discharge channel with embedded propellant distributor. Multiple materials were tested including ABS, ULTEM, and glazed ceramic. Thrust measurements were obtained at the NASA Glenn Research Center. Measured thrust ranged from 17.2–30.4 mN over a discharge power of 280 W to 520 W with an anode ISP range of 870–1450 s. The thruster has a similar performance range to conventional thrusters at the same power levels. However, the polymer ABS and ULTEM materials have low temperature limits which made sustained operation difficult.

scholarly journals Design and characterization of a 3D-printed staggered herringbone mixer

BioTechniques ◽  
2021 ◽  
Author(s):  
Vedika J Shenoy ◽  
Chelsea ER Edwards ◽  
Matthew E Helgeson ◽  
Megan T Valentine
Keyword(s):  
3D Printing ◽  
High Throughput ◽  
Low Cost ◽  
Microfluidic Devices ◽  
Device Design ◽  
Replica Molding ◽  
3D Printed ◽  
And Performance ◽  
To Receive

3D printing holds potential as a faster, cheaper alternative compared with traditional photolithography for the fabrication of microfluidic devices by replica molding. However, the influence of printing resolution and quality on device design and performance has yet to receive detailed study. Here, we investigate the use of 3D-printed molds to create staggered herringbone mixers (SHMs) with feature sizes ranging from ∼100 to 500 μm. We provide guidelines for printer calibration to ensure accurate printing at these length scales and quantify the impacts of print variability on SHM performance. We show that SHMs produced by 3D printing generate well-mixed output streams across devices with variable heights and defects, demonstrating that 3D printing is suitable and advantageous for low-cost, high-throughput SHM manufacturing.

scholarly journals Microstructured Surface Plasmon Resonance Sensor Based on Inkjet 3D Printing Using Photocurable Resins with Tailored Refractive Index

Polymers ◽  
2021 ◽  
Vol 13 (15) ◽  
pp. 2518
Author(s):  
Nunzio Cennamo ◽  
Lorena Saitta ◽  
Claudio Tosto ◽  
Francesco Arcadio ◽  
Luigi Zeni ◽  
...  
Keyword(s):  
Surface Plasmon Resonance ◽  
3D Printing ◽  
Surface Plasmon ◽  
Plasmon Resonance ◽  
Optical Sensor ◽  
Low Cost ◽  
3D Print ◽  
Spr Sensor ◽  
Resonance Sensor ◽  
3D Printed

In this work, a novel approach to realize a plasmonic sensor is presented. The proposed optical sensor device is designed, manufactured, and experimentally tested. Two photo-curable resins are used to 3D print a surface plasmon resonance (SPR) sensor. Both numerical and experimental analyses are presented in the paper. The numerical and experimental results confirm that the 3D printed SPR sensor presents performances, in term of figure of merit (FOM), very similar to other SPR sensors made using plastic optical fibers (POFs). For the 3D printed sensor, the measured FOM is 13.6 versus 13.4 for the SPR-POF configuration. The cost analysis shows that the 3D printed SPR sensor can be manufactured at low cost (∼15 €) that is competitive with traditional sensors. The approach presented here allows to realize an innovative SPR sensor showing low-cost, 3D-printing manufacturing free design and the feasibility to be integrated with other optical devices on the same plastic planar support, thus opening undisclosed future for the optical sensor systems.

3D Printable Resources for Engaging STEM Students in Laboratory Learning Activities and Outreach Programs: Inexpensive and User-Friendly Instrument Kits for Educators

MRS Advances ◽  
2018 ◽  
Vol 3 (49) ◽  
pp. 2937-2942 ◽  
Author(s):  
Lon A. Porter
Keyword(s):  
3D Printing ◽  
Mathematics Learning ◽  
Digital Design ◽  
Outreach Programs ◽  
Stem Students ◽  
3D Printed ◽  
Design Software ◽  
And Performance ◽  
And Mathematics ◽  
User Friendly

ABSTRACTContinued advances in digital design software and 3D printing methods enable innovative approaches in the development of new educational tools for laboratory-based STEM (science, technology, engineering and mathematics) learning. The decreasing cost of 3D printing equipment and greater access provided by university fabrication centers afford unique opportunities for educators to transcend the limitations of conventional modes of student engagement with analytical instrumentation. This work shares successful efforts at Wabash College to integrate user-friendly and inexpensive 3D printed instruments kits into introductory STEM coursework. The laboratory kits and activities described provide new tools for engaging students in the exploration of instrument design and performance. These experiences provide effective ways to assist active-learners in discovering the technology and fundamental principles of analysis and deliberately confront the “black box” perception of instrumentation.

scholarly journals Accessing 3D Printed Vascular Phantoms for Procedural Simulation

2021 ◽  
Vol 7 ◽  
Author(s):  
Jasamine Coles-Black ◽  
Damien Bolton ◽  
Jason Chuen
Keyword(s):  
3D Printing ◽  
Endovascular Procedures ◽  
Low Cost ◽  
3D Models ◽  
Routine Care ◽  
Aortic Aneurysms ◽  
Patient Specific ◽  
Ct Angiogram ◽  
Abdominal Aortic ◽  
3D Printed

Introduction: 3D printed patient-specific vascular phantoms provide superior anatomical insights for simulating complex endovascular procedures. Currently, lack of exposure to the technology poses a barrier for adoption. We offer an accessible, low-cost guide to producing vascular anatomical models using routine CT angiography, open source software packages and a variety of 3D printing technologies.Methods: Although applicable to all vascular territories, we illustrate our methodology using Abdominal Aortic Aneurysms (AAAs) due to the strong interest in this area. CT aortograms acquired as part of routine care were converted to representative patient-specific 3D models, and then printed using a variety of 3D printing technologies to assess their material suitability as aortic phantoms. Depending on the technology, phantoms cost $20–$1,000 and were produced in 12–48 h. This technique was used to generate hollow 3D printed thoracoabdominal aortas visible under fluoroscopy.Results: 3D printed AAA phantoms were a valuable addition to standard CT angiogram reconstructions in the simulation of complex cases, such as short or very angulated necks, or for positioning fenestrations in juxtarenal aneurysms. Hollow flexible models were particularly useful for device selection and in planning of fenestrated EVAR. In addition, these models have demonstrated utility other settings, such as patient education and engagement, and trainee and anatomical education. Further study is required to establish a material with optimal cost, haptic and fluoroscopic fidelity.Conclusion: We share our experiences and methodology for developing inexpensive 3D printed vascular phantoms which despite material limitations, successfully mimic the procedural challenges encountered during live endovascular surgery. As the technology continues to improve, 3D printed vascular phantoms have the potential to disrupt how endovascular procedures are planned and taught.

scholarly journals Novel 3D-Printed MEMS Magnetometer with Optical Detection

Proceedings ◽  
2018 ◽  
Vol 2 (13) ◽  
pp. 783 ◽  
Author(s):  
Matthias Kahr ◽  
Wilfried Hortschitz ◽  
Harald Steiner ◽  
Michael Stifter ◽  
Andreas Kainz ◽  
...  
Keyword(s):  
3D Printing ◽  
Product Development ◽  
Rapid Prototyping ◽  
Low Cost ◽  
High Accuracy ◽  
Structural Performance ◽  
Sensitivity Measurement ◽  
Optical Readout ◽  
3D Printed ◽  
Working Principle

This paper reports a novel 3D printed MEMS magnetometer with optical readout, which demonstrates the advantages of 3D printing technology in terms of rapid prototyping. Low-cost and fast product development cycles favour 3D printing as an effective tool. Sensitivity measurement with such devices indicate high accuracy and good structural performance, considering material and technological uncertainties. This paper is focusing on the novelty of the rapid, 3D-printing prototyping approach and verification of the working principle for printed MEMS magnetometers.

An Initial Effort to Create a Superficial Femoral Artery Ultrasound Phantom Using 3-Dimensional Printing

2020 ◽  
Vol 44 (2) ◽  
pp. 69-73
Author(s):  
Paul D. Bishop ◽  
Thomas Fultz ◽  
Lisa Smith ◽  
Ryan S. Klatte ◽  
Francis Loth ◽  
...  
Keyword(s):  
3D Printing ◽  
Femoral Artery ◽  
Superficial Femoral Artery ◽  
Low Cost ◽  
Duplex Ultrasound ◽  
3D Print ◽  
Stl File ◽  
Calcified Plaque ◽  
3D Printed ◽  
Artery Geometry

Three-dimensional (3D) printing of anatomical structures has yielded valuable models for simulation, education, and surgical planning applications. Applications for 3D printing have continued to expand to include some ultrasound applications. The goal of this effort was to evaluate if a 3D printed model of a superficial femoral artery (SFA) would have realistic ultrasound characteristics. A computed tomography scan was 3D reconstructed and segmented using TeraRecon Aquarius Intuition software (TeraRecon, Foster City, California) to obtain an atherosclerotic SFA geometry. Both the lumen geometry and calcified plaque geometry of the SFA were exported as a stereolithographic (STL) file. The STL file was printed with An Object350 Connex 3D System using 2 different materials selected based on published elastic modulus data. VeroWhite was selected for the calcified plaque and TangoPlus Clear was selected for the artery wall. After printing, the SFA model was imaged in a water bath with a Phillips IU22 duplex ultrasound console and L12-9 ultrasound probe. Ultrasound imaging of the SFA model yielded grayscale views of artery geometry. Lumen geometry of the SFA model was similar to the actual artery geometry. Ultrasound was able to discern between the 3D print materials and visualize regions with stenosis. Suboptimal ultrasound parameters of echogenicity and wave velocity noted to differ from biological tissue. Total 3D print material cost was estimated at below $20. Although the 3D printed model did not have fully accurate ultrasound characteristics, it still provided realistic imaging. With further research, 3D printed models may offer a low-cost alternative for ultrasound phantoms.

Power Deposition into the Discharge Channel of a Hall Effect Thruster

2014 ◽  
Vol 30 (1) ◽  
pp. 209-220 ◽  
Author(s):  
Rafael A. Martinez ◽  
Hoang Dao ◽  
Mitchell L. R. Walker
Keyword(s):  
Hall Effect ◽  
Discharge Channel ◽  
Power Deposition ◽  
Hall Effect Thruster

The Sparthan Three-Dimensional Printed Exo-Glove: A Preliminary Evaluation of Performance Via Case Study

2019 ◽  
Vol 13 (3) ◽  
Author(s):  
Tomás A. Georgiou ◽  
Davide Asnaghi ◽  
Alva Liang ◽  
Alice M. Agogino
Keyword(s):  
Light Intensity ◽  
Daily Living ◽  
Low Cost ◽  
Three Dimensional ◽  
Preliminary Evaluation ◽  
Evaluation Of Performance ◽  
3D Printed ◽  
Hand Exoskeleton ◽  
And Performance

This paper describes the development and testing of a low-cost three-dimensional (3D) printed wearable hand exoskeleton to assist people with limited finger mobility and grip strength. The function of the presented orthosis is to support and enable light intensity activities of daily living and improve the ability to grasp and hold objects. The Sparthan Exoskeleton prototype utilizes a cable-driven design applied to individual digits with motors. The initial prototype is presented in this paper along with a preliminary evaluation of durability and performance efficacy.

scholarly journals Development of Soft sEMG Sensing Structures Using 3D-Printing Technologies

Sensors ◽  
2020 ◽  
Vol 20 (15) ◽  
pp. 4292
Author(s):  
Gerjan Wolterink ◽  
Pedro Dias ◽  
Remco G. P. Sanders ◽  
Frodo Muijzer ◽  
Bert-Jan van Beijnum ◽  
...  
Keyword(s):  
3D Printing ◽  
Biceps Brachii ◽  
Low Cost ◽  
Recognition Algorithm ◽  
Practical Applications ◽  
Variable Level ◽  
Processing Step ◽  
Significant Difference ◽  
3D Printed ◽  
Emg Electrodes

3D printing of soft EMG sensing structures enables the creation of personalized sensing structures that can be potentially integrated in prosthetic, assistive and other devices. We developed and characterized flexible carbon-black doped TPU-based sEMG sensing structures. The structures are directly 3D-printed without the need for an additional post-processing step using a low-cost, consumer grade multi-material FDM printer. A comparison between the gold standard Ag/AgCl gel electrodes and the 3D-printed EMG electrodes with a comparable contact area shows that there is no significant difference in the EMG signals’ amplitude. The sensors are capable of distinguishing a variable level of muscle activity of the biceps brachii. Furthermore, as a proof of principle, sEMG data of a 3D-printed 8-electrode band are analyzed using a patten recognition algorithm to recognize hand gestures. This work shows that 3D-printed sEMG electrodes have great potential in practical applications.

Sign in / Sign up

Export Citation Format

Share Document