Effect of CAD/CAM Ceramic Thickness on Shade Masking Ability of Discolored Teeth: In Vitro Study

Shade matching is a common challenge that dentists face during fabrication of esthetic dental restoration. Thus, the aim of the current study was to assess the masking ability of two types of CAD/CAM ceramics for gaining high esthetic prosthesis. This in vitro study used a total sample size of 66 lithium disilicate (LD) and leucite reinforced (LR) CAD/CAM ceramics sub-grouped into three thicknesses: 0.5, 1, and 1.5 mm. Nine shades of natural dentin die materials were prepared as a replica of the underlying tooth structure. The difference in color (ΔE) and translucency parameter (TP) were assessed for both tested ceramics at the three thicknesses. One-way ANOVA was performed to compare the three thicknesses of each ceramic, followed by multiple pairwise comparisons between both ceramics. LR had significantly higher ΔE than LD at all thicknesses used unlike the case in TP. Thickness of 0.5 mm exhibited the highest ΔE and TP, while 1.5 mm thickness showed the lowest ΔE and TP in both ceramics. Increase in ceramic thickness had a great impact on both color masking ability of the underlying tooth structure and its translucency. The higher the ceramic thickness, the better the masking ability and the lower the translucency was reported.

Hardness of Resin Cements Polymerized through Glass-Ceramic Veneers

(1) Background: The aim of this study is to evaluate the hardness of resin cements polymerized through ceramic disks under different process factors (ceramic type and thickness, light-polymerization units and polymerization time); (2) Method: Three types of ceramic blocks were used (IPS e.max CAD; Celtra Duo; VITABLOCS). Ceramic disks measuring 0.5 mm, 1.0 mm and 1.5 mm were cut from commercial blocks. Two resin cements (Rely X Veneer and Variolink Esthetic) were polymerized through the ceramic specimens using distinct light-polymerization units (Deep-cure; Blue-phase) and time intervals (10 and 20 s). Hardness of cement specimens was measured using microhardness tester with a Knoop indenter. Data were statistically analyzed using factorial ANOVA (α = 5%); (3) Results: Mean microhardness of Rely X Veneer cement was significantly higher than that of Variolink Esthetic. Deep-cure resulted in higher mean microhardness values compared to Blue-phase at 0.5- and 1-mm specimen thicknesses. Moreover, a direct correlation was found between polymerization time and hardness of resin cement; (4) Conclusions: Surface hardness was affected by resin cement type and ceramic thickness, and not affected by ceramic types, within evaluated conditions. Increasing light-polymerization time significantly increased the hardness of the cement.

Effect of lithium disilicate ceramic thickness, shade and translucency on transmitted irradiance and knoop microhardness of a light cured luting resin cement

This in vitro study evaluates the influence of pressed lithium disilicate thickness, shade and translucency on the transmitted irradiance and the Knoop microhardness (KHN) of a light-cured resin cement at two depths. One hundred and thirty-five ceramic discs of IPS e.max Press (Ivoclar Vivadent) were fabricated and divided into twenty-seven groups (n = 5) according to the association between translucency: HT (hight translucency), LT (low translucency), and MO (medium opacity); shade: BL2, A1 and A3.5; and thickness: 0.5 mm, 1.5 mm, and 2.0 mm. One side of each ceramic disc was finished, polished and glazed. The irradiance (mW/cm²) of a multiwave LED light curing unit (Valo, Ultradent) was evaluated with a potentiometer (Ophir 10ª-V2-SH, Ophir Optronics) without (control group) or with interposition of ceramic samples. The microhardness of Variolink Esthetic LC resin cement (Ivoclar Vivadent) was evaluated after 24 h at two depths (100 μm and 700 μm). Data were submitted to ANOVA followed by Tukey’s test (α = 0.05). Irradiance and KHN were significantly influenced by ceramic thickness (p < 0.0001), shade (p < 0.001), translucency (p < 0.0001) and depth (p < 0.0001). Conclusions: the interposition of increasing ceramic thicknesses significantly reduced the irradiance and microhardness of resin cement. Increased depth in the resin cement showed significantly reduced microhardness for all studied groups. Increased ceramic opacity reduced the KHN of the resin cement at both depths for all ceramic thicknesses and shades.