pavement preservation
Recently Published Documents


TOTAL DOCUMENTS

112
(FIVE YEARS 22)

H-INDEX

9
(FIVE YEARS 2)

2021 ◽  
Author(s):  
George Vorobieff

Australia introduced conventional longitudinal diamond grinding of highway concrete pavements in 2009 with the purchase of two "4‐foot" highway grinding machines by two contractors. The availability of these machines in Australia has enabled contractors to improve ride quality of new pavements, rather than accept a deduction to the tendered rate for the supply and placement of concrete pavement. Grinding of new concrete base is permitted up to an IRI of 3.5 m/km, thereby reducing the need to remove and replace concrete pavement which met the specified thickness, strength and density, but not ride quality. More importantly, with the introduction of the grinding machines, asset managers have the opportunity to use diamond grinding to treat existing concrete pavements that have a rough ride, or when the textured surface no longer meets specified levels for skid resistance. Although the primary use of diamond grinding was to improve ride quality of new and existing concrete pavements, it has also been used to: treat stepping across transverse contraction joints in PCP, improve skid resistance at roundabouts, improve both ride quality and texture for JRCP pavements (greater than 40 years of age) with a thin wearing course and spalling in the asphalt at transverse joints. The above treatments to concrete pavement allow asset preservation and avoid high reconstruction costs. The Austroads concrete pavement design procedure is based on the PCA design method and road smoothness is not a design parameter, unlike the USA approach to concrete pavement design where ride quality is a design input. There is still much work to be done to convince asset managers in Australia that the removal of the high areas of a concrete pavement to smooth the surface, reduces the dynamic wheel loading and minimises accumulated fatigue stress in the concrete. This paper reviews the last 10 years of diamond grinding projects and the success of this pavement preservation treatment for new and existing urban and rural concrete pavements in Australia. Recommendations to reduce the cost of diamond grinding concrete pavements and extend the use of this treatment are also provided.


2021 ◽  
Vol 147 (4) ◽  
pp. 05021002
Author(s):  
Sadie Casillas ◽  
Andrew Braham

Author(s):  
Rahul Jichkar

In this project Pavement failure is defined in terms of decreasing serviceability caused by the development of cracks and ruts. Before going into the maintenance strategies, we must look into the causes of failure of rigid pavements. Failures of rigid pavements are caused due to many reasons or combination of reasons. Application of correction in the existing surface will enhance the life of maintenance works as well as that of strengthening layers. It has been seen that only three parameters i.e., unevenness index, pavement cracking and rutting are considered while other distresses have been omitted while going for maintenance operations. Along with the maintenance techniques there are various methods for pavement preservation which will help in enhancing the life of pavement and delaying its failure. The purpose of this study was to evaluate the possible causes of pavement distresses, and to recommend remedies to minimize distress of the pavement. The project describes lessons learnt from pavement failures and problems experienced during the last few years on a number of projects in India. Based on the past experiences’ various pavement preservation techniques and measures are also discussed which will be helpful in increasing the serviceable life of pavement


2021 ◽  
Vol 11 (5) ◽  
pp. 2147
Author(s):  
Shifu Liu ◽  
Yu Tian ◽  
Le Liu ◽  
Peng Xiang ◽  
Zhekai Zhang

Pavement evaluation is critical for the decision-making process of pavement preservation and rehabilitation. Roughness is a key airport pavement characteristic that has been linked to impacts such as safety and service life. The Boeing Bump is one of the few roughness evaluation methods that has been developed specifically for runways. Although it is superior to the widely used International Roughness Index (IRI), it does not take into account the superposition effect of continuous runway bumps. Based on the ADAMS/Aircraft virtual prototype platform, this paper establishes and verifies five typical models (B737, B747, B757, B777, and B787) and then analyzes the most unfavorable speed (in terms of aircraft vibration) of each model and the dynamic responses caused by multiple bumps. The original Boeing Bump is improved and optimized by determining dynamic response thresholds for the various aircraft types. The results show that the revised Boeing Bump is more realistic than the original version, especially with regard to medium and long wave bands.


Author(s):  
Farhang Jalali ◽  
Adriana Vargas-Nordcbeck

Chip seals are effective pavement preservation treatments that are usually applied to address non-fatigue cracking, weathering, and raveling, to seal the surface, to delay oxidation, and, finally, to improve skid resistance. This study used field performance data of test sections from the Pavement Preservation Group Study being conducted by the National Center for Asphalt Technology and the Minnesota DOT’s Road Research Facility. Data from test sections located in a low-traffic-volume road with a hot, wet, no-freeze climate collected over a period of 7 years were used to evaluate the effect of several chip seal treatments. Treatments range from single layer to multilayer systems, and include different construction techniques such as rejuvenating scrub seal and fiber membrane. Also, a section was crack sealed before the application of a single layer chip seal to assess the benefits. A semi-parametric survival analysis was performed to determine the differences in median time to failure (MTTF) for different chip seal sections versus a controlled section—representing a “do-nothing” scenario. The results showed that the MTTF for a single layer chip seal ranges from 6.8 to 9.1 years depending on the pretreatment condition. Crack sealing before chip seal could extend the MTTF by an additional 1–3 years, depending on initial conditions. Double and triple layer chip seals extend the MTTF beyond 10 years. Finally, the scrub seal provided the highest benefits, with survival rates close to 100% after 10 years of performance.


2021 ◽  
Author(s):  
Theodora Konstantinou ◽  
Diala Haddad ◽  
Akhil Prasad ◽  
Ethan Wright ◽  
Konstantina Gkritza ◽  
...  

Electric Roadways (ERs) or Dynamic Wireless Charging (DWC) lanes offer an alternative dynamic and wireless charging method that has the potential of giving electric vehicles (EV) limitless range while they are moving. Heavy-duty vehicles (HDVs) are expected to be early adopters of the DWC technology due to the higher benefits offered to these vehicles that are traveling on fixed routes. The goal of this project was to assess the feasibility of ERs in Indiana and design a test bed for in-road EV charging technologies. The most suitable locations for implementing DWC lanes were identified on interstates that are characterized by high truck traffic. Using I-65 S as a case study, it was found that DWC can be economically feasible for the developer and competitive for the EV owner at high and medium future projections of EV market penetration levels. However, the existing substations are unlikely to serve future DWC needs for HDVs. Thus, consideration should be given to substation expansion to support EVs as market penetration expands. Implementing the DWC technology on interstates and jointly with major pavement preservation activities is recommended. Large scale deployment can significantly reduce the high initial investment. Renewable energy resources (solar and wind) deployed in the vicinity of ERs can reduce the electricity costs and associated greenhouse gas emissions.


Author(s):  
Jared Munch ◽  
Uma Maheswar Arepalli ◽  
Manik Barman

Crack sealing is an important preventive treatment in the pavement preservation program. To achieve a cost-effective crack seal, it is crucial to select a proper crack sealing method. In Minnesota asphalt pavement cracks are sealed using both the clean-and-seal and rout-and-seal methods; however, there is no guideline for choosing the most suitable crack sealing method. This study deals with a literature review, an online survey, crack seal performance data collection, cost-effectiveness analysis of the crack sealing methods, life cycle cost analysis, and development of two decision trees to aid in selecting the most suitable crack sealing method. The first, which can be used in the pavement management system, needs information such as crack severity, pavement type (new versus overlay), pavement analysis period and design life, traffic level, and crack seal sequence (first, intermediate, or last). The second decision tree, which is a simplified version of the first and can be used by preventive maintenance crews, requires less information, such as crack severity, traffic level, and place in the crack sealing sequence.


2020 ◽  
Author(s):  
Lerose Lane ◽  
R. Gary Hicks ◽  
DingXin Cheng ◽  
Erik Updyke

This manual presents best practices on project selection, mix design, and construction to ensure a superior product when constructing thin asphalt overlays. Experience shows these treatments provide excellent performance when placed on pavements in fair to good condition using proper construction techniques. Though sometime referred to by other names, thin asphalt overlays have been widely used for pavement preservation throughout the world for over 50 years. Limited infrastructure funding at the local, state, and federal levels has resulted in greater emphasis on the use of pavement preservation techniques to extend pavement life and reduce maintenance costs. Thin asphalt overlays are one of many preventative maintenance treatments. Thin asphalt overlays are placed directly on existing pavement and can range from 1/2 inch to 1 1/2 inches in thickness. Thin asphalt overlays have proven to be an economical means for maintaining and improving the functional condition of an existing pavement since the 1960s. Specifically, this manual provides guidance for engineers regarding where and when to use thin asphalt overlays including: (1) Types and variations of thin overlays; (2) Materials and the design process; (3) Construction; (4) Quality Assurance; and (5) Troubleshooting. This chapter by chapter guidance enables an Agency’s engineers to design and construct a successful thin asphalt overlay project to completion. This manual is one of four new manuals prepared by the California Pavement Preservation Center (CP2Center) using funding from California Senate Bill 1 (SB-1), passed in April 2017. The other three manuals provide detailed design and construction information for (1) chip seals, (2) slurry surfacing, and (3) Cape seals. The creation of these manuals was a task funded entirely from SB-1 monies for the purpose of disseminating training and technical information on highway pavement preservation to local agencies throughout California.


Sign in / Sign up

Export Citation Format

Share Document