Method for Determining the Casing Pressure in Uncompacted Sandy Bases When Installing Bored Piles

2021 ◽  
pp. 215-218
Author(s):  
D. V. Popov ◽  
E. V. Savinova
Keyword(s):  
Bored Piles ◽  
Casing Pressure

Avoiding Sustained Casing Pressure in Gas wells using Self Healing Cement

2011 ◽  
Author(s):  
Salim Taoutaou ◽  
Jorge Andres Vargas Bermea ◽  
Pietro Bonomi ◽  
Bassam Elatrache ◽  
Christian Pasturel ◽  
...  
Keyword(s):  
Self Healing ◽  
Gas Wells ◽  
Sustained Casing Pressure ◽  
Casing Pressure

Experimental Investigation During Stall and Surge in a Transonic Fan Stage and Rotor-Only Configuration

2006 ◽  
Author(s):  
A. J. Gannon ◽  
G. V. Hobson ◽  
R. P. Shreeve ◽  
I. J. Villescas
Keyword(s):  
High Speed ◽  
Fast Response ◽  
Pressure Measurements ◽  
Post Processing ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
The Difference ◽  
Data Signal ◽  
Transonic Fan ◽  
Casing Pressure

High-speed pressure measurements of a transonic compressor rotor-stator stage and rotor-only configuration during stall and surge are presented. Rotational speed data showed the difference between the rotor-only case and rotor-stator stage. The rotor-only case stalled and remained stalled until the control throttle was opened. In the rotor-stator stage the compressor surged entering a cyclical stalling and then un-stalling pattern. An array of pressure probes was mounted in the case wall over the rotor for both configurations of the machine. The fast response probes were sampled at 196 608 Hz as the rotor was driven into stall. Inspection of the raw data signal allowed the size and speed of the stall cell during its growth to be investigated. Post-processing of the simultaneous signals of the casing pressure showed the development of the stall cell from the point of inception and allowed the structure of the stall cell to be viewed.

The Calculation Method and Experimental Research on Throttling Pressure Drop during Kill a Well

2012 ◽  
Vol 229-231 ◽  
pp. 495-498
Author(s):  
Hui Xin Liu ◽  
Xian Min Yang ◽  
Cheng Tao Li ◽  
Xiang Cheng
Keyword(s):  
Pressure Drop ◽  
Calculation Method ◽  
Engineering Practice ◽  
Exploration Process ◽  
Throttle Valve ◽  
Long Time ◽  
Valve Opening ◽  
Casing Pressure ◽  
The Relationship ◽  
Control Accuracy

There is a common problem during kill a well, which is how to quickly and accurately control the surface casing pressure according to the requirements for killing a well. A step-by-step exploration process is employed on operation sites. Continuously adjusting throttle valve to acquire surface casing pressure may lead to failure of kill operation because of its long time and low control accuracy. Obviously, if the calculation problems of throttling drawdown can be resolved,the relationship between drawdown and throttle valve opening can be found and the course of explorating can be converted into a straight course.Then the success rate of killing well can be improved. More importantly, this can make automatic controll of surface casing pressure possible. The paper built the calculation method of throttling pressure drop by theoretical analysis and verified the calculation method by adopting it into field test. The result has showed that the calculation method of throttling pressure drop coincides with experimental results and it can be used in engineering practice.

Sign in / Sign up

Export Citation Format

Share Document